- Premier Blogs
- Win Stuff
If the pedal is passing signal and works properly, but seems unusually noisy, there are a number of things that could be causing the problem. First, check the power supply. Using the wrong power supply can cause noise and hum, and can damage your pedal. A generic power supply like you find at Radio Shack should never be used with pedals. You need one designed for effects, one that is both regulated (voltage does not
drift) and filtered (no noise from the AC line). If the pedal runs at 9 volts, try testing it with a battery.
After you’ve confirmed the power supply as the cause, you can look at the pedal itself. When testing a pedal for noise, set the volume knob for unity gain (the volume is the same whether the pedal is on or off). Turning the volume up will amplify any noise that’s already there, making it more apparent. If you turn your guitar volume all the way down, you can hear what’s actually coming from the pedal. A slight white noise is normal on many pedals when set at unity gain. If you are hearing excessive noise from your pedal when it’s not boosting your signal, try to determine what sort of noise it is.
Humming noise is a low frequency, consistent hum, like you hear when playing a guitar with single coil pickups near electronics. This usually comes from AC power leaking into your signal somewhere, or it could be your guitar pickups. Try a guitar with humbucking pickups to make sure the noise is actually coming from the pedal and not the guitar. Hum can also come from a bad ground, like the sound you hear when you pull the cord out of your guitar.
Static noise is an inconsistent crackling, like a bad cable or guitar jack would make, which is often caused by a loose connection in the pedal—in one of the jacks, wires or the switch. It can also be caused by a very sick component (transistor, e.g.).
White noise, a sort of a hissing sound, is another common type. Most pedals will have some, but excessive white noise could be due to some bad electronic components or a need for calibration. The last common type of noise is a high-pitched squealing sound. This can be caused by feedback oscillations in the pedal due to poor wiring layout—wires should not be in neat parallel lines, like those found in some boutique pedals. In analog delay pedals and others with BBD chips (chorus, flangers, etc), squealing can be caused by poor calibration.
Open up the pedal while it’s still plugged into the guitar and amp, leaving the volume on the guitar all the way down. Probe the inside of the pedal with some non-conductive device to see if you can locate the source of the noise. It could be a bad solder joint, failing switch contact, faulty connections with a jack or pot, or it could be a faulty component on the board. Try wiggling the battery clip to see if that causes any noise. You can also try to re-route the wires to stop some noises, like whistling. Unfortunately with most mass-produced pedals made these days, there is nothing you can really do inside: everything is directly soldered to the board, no hand wiring, and using proprietary parts that can’t be replaced. When one of these pedals dies past the warranty, you’re probably holding a paperweight.
Many problems, especially on older pedals, are caused by poor solder joints. This problem may be getting worse, as most builders are being forced to use lead-free solder for European RoHS. If you can wiggle a wire or component, and the lead moves on the attachment point, the joint is very bad and needs to be redone. The best repair is to de-solder it and redo it with fresh solder. If you don’t have de-soldering tools, touching it up with a little new solder usually does the trick. (There’s a great tutorial called “how and why to solder correctly” on YouTube.) Often the solder joint is not physically loose but will be dull and chalky—another sign of a bad joint. Intermittent sound, and noise caused by poor solder joints, can often be exposed by gently twisting the circuit board. If twisting the board cuts the signal on and off, there is probably a bad joint somewhere.
Noise is relative, so you may want to compare your noisy pedal to a similar one (there’s a reason some people call them noise toys). If there is definitely a problem but you just can’t figure it out, it’s time for professional help. If the warranty is still valid, that’s your best bet. Otherwise, see if you can find a qualified local repairman to bring it to. Often the problem will disappear when your effect is tested by a tech, like about half of all pedals we get in for repairs. Maybe they just like getting out of the house.
Check back with us next month. Until then, keep on stompin’!
(a.k.a. Analog Tom) is the owner and proprietor of For Musicians Only (formusiciansonly.com) and author of Analog Man’s Guide To Vintage Effects. For Musicians Only is also the home of the FMO Gear Shop. Questions or comments about this article can be sent to: firstname.lastname@example.org.
(analogman.com) is one of the largest boutique effects manufacturers and retailers in the business, established by “Analog” Mike Piera in 1993. Mike can be reached at AnalogMike@aol.com.