- Rig Rundowns
- Premier Blogs
|Download Example 1
80's style rock duet (bridge pickup)
|Download Example 2
Shredding away (bridge pickup)
|Download Example 3
Clean tone (neck pickup)
|Signal path is Godin RL3 into Creation Audio Labs MW1-studio tool (DI) - Pro Tools - Overloud TH1 Amp Plugin|
The Redline 3 is an attractive and thoughtful instrument that was born to rock… er, shred... and is styled around a rock maple neck with a rosewood or maple fingerboard (the review guitar was rosewood) and 22 of the biggest jumbo frets I’ve encountered on a guitar. The scale is 25-1/2” and the fingerboard measures 1-11/16” at the nut. The body is constructed from a silverleaf maple center with poplar wings. The review guitar came with a killer— and perfectly book-matched—transparent red flame maple top and sported a pair of EMG active humbuckers (85 in the neck, 81 in the bridge). Standard controls include a 3-way slide switch with one Volume and one Tone knob, shared by both pickups. Topping off theRedline 3 is a licensed Floyd Rose tremolo with a deep recess cut in the body for reverse dive-bomb pull-ups.
Before plugging in, I spent some time with the guitar unplugged to get an idea of what was happening with its tone. This is a snappy instrument with a lot of pop and bite, but not at the expense of some body in its sound. The maple center gives the guitar an immediate attack, and the poplar wings add warmth to the tone to balance it out. Notes rang out clear and fairly long, though the Floyd did take a little of the natural sustain out (a common side effect of virtually any tremolo), but not enough to be an issue. It sat nicely on my lap, and the contour body cut was a welcome design choice, keeping the guitar comfortable during long playing sessions. Rather than a neck plate, the RL3 uses four recessed screws that stay completely out of the way and add an elegant touch to the look of the back of the guitar, as does the rear bottom horn-to-body contour. The neck is radiused very flat at 16”, which allows you to rip and bend across the guitar with pinpoint accuracy and extreme speed. The neck carve isn’t terribly shallow, nor is it baseball bat-like, and it fit my hand nicely without inducing much fatigue. While I prefer a slightly “clubby” neck, that isn’t necessarily in line with this style of guitar, so Godin hit the mark for their target audience. The neck is finished in a light satin that adds to the sleek and speedy feel, and the massive frets make sure you get big tone and killer control without sacrificing playability. Nice.
Since there were a variety of amps at the studio during my time with the RL3, I had the chance to run it through quite a few to get a feel for how it handled different situations. Whenever I think of a shredder guitar, it usually involves pickups like a Duncan Distortion or DiMarzio Super Distortion Humbucker, but that’s just my age talking. Godin went the modern route with EMGs, and it lends a decidedly modern sound to the guitar. Through most of the amps, I had to back down the gain on the amp to accommodate the higher-output pickups. This type of front-end hit to an amp can be used quite beneficially, if you’re looking for a super-tight bottom and searing top end. These pickups are certainly not subtle, and it’s obvious why so many modern metal bands use this exact combination! Not surprisingly, the guitar tended to favor higher-gain amps like an Engl Ritchie Blackmore head, Mesa Boogie Dual Rectifier and a Krank Rev Jr. With classic amps, like a Marshall Super Lead and a VOX AC30, the tone was decidedly less “classic” and lacked some of the dimension that comes through with lower-gain pickups. To be fair, Godin did not intend to create another Les Paul or Strat, so there’s no reason to spend a lot of time trying to make it something it isn’t. Clean tones were more sparkly than chimey on the top end, but the solid low end was very impressive and lent an authoritative presence to the sound that would never get lost in a mix.