Enter for your chance to win!

May 2014
more... GearDIYHow-TosBass GearUpkeepJanuary 2013

DIY: How to Set Up a Bass Guitar

DIY: How to Set Up a Bass Guitar

Photos by Ariel Ellis

I’ve read many articles and repair manuals on bass setup, and I’ve personally set up thousands of basses as a professional. So when PG asked me to write a DIY piece on the subject, I thought, “What can I bring to this discussion that’s truly helpful? Is there a little something I can describe that you don’t already know?”

In this article, we’ll cover the essentials with the goal of helping you decide what you can handle yourself and what you should leave to your local repair technician. Even if there are aspects of the job you’re not prepared to attempt on your own, it’s good to understand what’s involved with a bass setup. Knowing the steps and terminology will let you communicate more confidently and effectively with your repair guy or gal.

More than likely you’re thinking about setup because in some way, your instrument is not performing the way you’d like. To pinpoint any problems, we need to look at all the factors that affect your instrument’s overall playability, sound, and function.

Preliminary Inspection
Our journey begins with a general inspection (Photo 1), which consists of playing the instrument while asking yourself these questions: Is the action too high? Too low? Are there buzzing frets? If so, that indicates a need for adjustment.

1. A setup begins with a preliminary, hands-on inspection of your bass. Check playability and listen for issues like buzzing frets and hardware rattles. List any problems you find.

While you’re at it, work the volume and tone controls, checking for noise. Gently jiggle the 1/4" plug at the output jack to check it for noise. Are there any hardware-related rattles? Take notes on all your observations and list any issues you need to address.

After you’ve given your bass a hands-on evaluation, you’re ready to get to work on the setup.

Tip: Because the adjustments that control playability are affected by string gauge and tension, be sure your bass sports the type of strings you plan to use. If you change string gauge, you’ll need to do a fresh setup to accommodate the new strings.

Step 1: Measure the Neck Relief

We start with checking the “relief” or amount of bend in the neck. I often see people sighting down the neck from all angles and making some very ballpark assessments about neck relief. But the precise and accurate way to measure relief is to use the strings as a straightedge. Here’s how to measure neck relief:

1. Tune your bass to pitch. Use the primary tuning you put this instrument in when performing or recording.
2. With your fretting hand, hold your lowest string against the 1st fret as if you were playing that note.

2. To gauge the amount of relief in your neck, use both hands to simultaneously fret the 4th string at the 1st fret and somewhere between the 14th and 16th frets. At the mid point between these two fretted notes, look at the gap between the bottom of the string and the top of the frets. To get another perspective on this gap, bounce the string against the frets with your picking-hand index finger.
3. Stretch your picking hand across the fretboard with your thumb aiming towards the bridge and index finger extended toward the nut (Photo 2). Open your hand as far as you can comfortably stretch and fret the lowest string with your thumb. The object is to move your thumb as close to the bridge as you can, while allowing your index finger to touch the lowest string approximately halfway between your fretting finger at the 1st fret and picking hand thumb. (Depending on the fretboard scale length, my picking hand thumb lands on the 14th, 15th, or 16th fret.) Now the lowest string is fretted at two points with two hands. With the lowest string secured at the 1st and, say, 15th fret, you can now use it as a straightedge.
4. With your picking-hand index finger, tap the string against the middle frets. By repeatedly tapping and releasing, you’ll be able to gauge how much space lies between the bottom of the string and the top of those frets. The gap (if any) is the amount of relief. How much of a gap you need depends very much on your playing style, but to get started, I adjust an instrument to have a gap that’s equivalent to the thickness of one or two business cards.

Tip: Make sure you continually check the tuning of your bass so it stays at pitch. This is crucial for making accurate measurements and adjustments.

Step 2: Adjust the Truss Rod

This is very important: If you don’t feel comfortable adjusting your truss rod or don’t have the proper tool, take this to your local qualified repair technician. You can really mess up your instrument by stripping the threads on your truss rod or over tightening and breaking this critical part of the neck. Whether the truss rod is adjusted via a male hex nut, a female socket, or a Phillips nut at the neck heel, make sure your tool has a snug fit so you don’t strip out this vital part.

3. To remove the neck to expose a truss rod that’s installed at the heel, take off the strings and back out the screws at the neck plate. 4. Once the screws have released the neck, gently pull it free from the body being careful not to scratch the neck on the exposed screw tips.

The vast majority of truss rods adjust clockwise to tighten and counter-clockwise to loosen. If your truss rod is located at the headstock, look down the neck from headstock to body to determine clockwise and counter-clockwise direction. If your truss rod adjustment is at the heel of the neck, you’ll need to remove it (Photos 3 and 4). The movements will be the same when you look from the heel down

Tip: If you have any doubts about how to adjust a truss rod, get a guitar repair book or study the manual that came with your instrument. Many manufacturers offer free online instructions for adjusting the truss rods on their guitars.

If you decide you want to change the gap between the string and fret, here’s the process:

1. To reduce the gap between string and fret, tighten the truss rod. Conversely, to increase the space between string and fret, loosen it. Move the truss rod in quarter-turn increments.
2. Retune and recheck relief each time you move the rod.

Continue the process until you get the desired gap between the string and fret. Again, unless you have a specific gap in mind, shoot for the thickness of one or two business cards.

5. Truss rods accessed at the neck heel are often adjusted with a screwdriver. 6. Whether the truss rod is installed at the headstock or neck heel, the vast majority adjust clockwise to tighten and counterclockwise to loosen.

If your bass requires adjustments at the neck heel (Photos 5 and 6), rather than the headstock, you’ll face the tedious prospect of reinstalling the neck and restringing to check each adjustment.

Tip: If your truss rod seems very difficult to adjust, or stops moving, or makes a loud noise, see a local repair tech. Although adjusting a truss rod may be foreign to you, all qualified technicians understand how it functions. It’s definitely worth paying the price to have this done right.

There are several adjustments that affect action, but they need to be done in the correct order. Because your decisions about all the other action-related adjustments are based on neck relief, it’s important to deal with the truss rod first. Once you’ve made any necessary truss-rod adjustments, you’re ready to move on to the other factors that control playability.

7. To reattach the neck, carefully place the heel into the neck pocket and then insert the screws by hand, slipping them through the body and seating the tips into their respective holes. 8. Tighten the neck screws securely. As you do this, use your free hand to control the screwdriver tip so it doesn’t slip out and mar the body.

If you’ve removed the neck to make truss rod adjustments, reattach it now (Photos 7 and 8), restring, and retune.

Post a comment to this article