Island’s Forty-Four is a handcrafted, handsome reinterpretation of the small-bodied, single-pickup Harmony H44.
It wasn’t long ago that Harmony guitars
of the ’50s and ’60s were considered ill-suited
to serious music making. But such
guitarists as the Black Keys’ Dan Auerbach
and Marc Ribot have made amazing, signature
sounds on these (once) affordable axes.
And in their wake, players, collectors, and
even guitar makers have reexamined the
merits of these guitars while driving prices
on the vintage market ever higher.
Nic Delisle, the luthier behind Island
Instrument Manufacture, uses Harmony,
Silvertone, and other department-store
guitars as points of departure for his own
idiosyncratic designs that sound and look
like few other guitars on the market—an
impressive feat for a builder only in his mid
20s. But while Harmony guitars were mass-produced
in a large factory, Delisle makes
each Island instrument by hand in a shop
in Montreal’s Mile-End—a neighborhood
known worldwide for its robust independent
music scene.
One of Island’s latest offerings, the Forty-Four, is a handsome reinterpretation of the
small-bodied, single-pickup Harmony H44
that Marc Ribot used to great effect. And as
our review guitar, which is fresh off Delisle’s
workbench, makes clear, that once lowly
design, relegated for decades to the dustiest
junk shop corners, is an excellent platform
for design improvements.
Smart Design Extrapolation
With its single cutaway and narrow waist,
the Forty-Four shares the same silhouette
as its inspiration. But there are key distinctions
between the Island and the Harmony
original. The Forty-Four has a bolt-on
neck instead of the H44’s neck-through
construction and employs a string-through-body
configuration inspired by the Fender
Telecaster. And by scrapping dot position
markers and a pickguard, Delisle has given
the Island a more minimalist look.
A conscientious builder, Delisle prefers
to source domestic or reclaimed timbers.
And when he uses an exotic hardwood, he
donates a percentage of the proceeds to
a reforestation initiative in Nicaragua. In
this case, the one-piece body is cut from
sinker cedro espino recovered from the
Panama Canal. The neck is carved from quarter-sawn poplar, while the fretboard,
headstock overlay, and bridge base are all
fashioned from black locust that’s given an
ebonized and distressed treatment befitting
a vintage-inspired guitar.
Though the design has an almost
elemental and basic feel, the Forty-Four is a
looker. Gold hardware often looks chintzy,
but the guitar is so minimal elsewhere that
the gold open-back Gotoh 510 tuners,
EVO fretwire, and strap buttons all bring
out warmth in the woods rather than beam
like garish afterthoughts. The brass compensated
saddle, which was custom made
by luthier Mark Kett, is elegantly sculptural,
and the gold-foil pickup, custom crafted
by Vintage Vibe Guitars’ Pete Biltoft, calls
to mind a tiny mid-century radio.
The Forty-Four’s ivoroid tuner buttons,
truss rod cover, and control knobs offer a
nice complement to the brown and gold
of the woods and hardware. And in a nod
to the time-honored bar band tradition of
using the red rubber washers from Grolsch
beer bottles as strap locks, Delise includes
them as standard equipment here. Another
nice touch is the hangtag, handwritten on a
rectangle originating from a cardboard box
of St-Ambroise Pale Ale—another detail
affirming Delisle’s commitment to using
domestic and recycled materials (and his
taste for good brew, apparently).
The Forty-Four feels solidly built, thanks
in part to the five bolts connecting its neck
and body. Craftsmanship on the guitar is very
good. The oil finish on the neck and body
feels smooth and fast. The frets are all well
seated and cleanly polished, although just a
tad sharp at the edge of the fretboard. Upon
super-close inspection, I found small imperfections
in spots—a dimple in the body’s
wood near the pickup, for instance. But then
again, this is a handmade instrument and not
the product of CNC machinery, so inconsequential
little anomalies suit the personal,
bespoke, arts-and-crafts feel of the instrument.
With its 45-millimeter (about 1.77") nut
and 56-millimeter (2.2") saddle spacing, the
Forty-Four has a wide neck for an electric
guitar. But it’s more than manageable for
a guitarist accustomed to tighter quarters,
thanks to its comfortable neck profile, which
is shallow, but not skimpy. The guitar left
Island’s shop with sleek, low action, and it is
equally comfortable to play in all its registers.
Although it shipped with strings that are
heavier than normal for an electric—a .012–.052 La Bella set with a wound third string—it isn’t difficult to bend the strings, thanks to
the fretboard’s rather flat 16" radius.
Ratings
Pros:
Terrific sound and playability. An affordable, handmade boutique guitar with a vibe all its own.
Cons:
Some players might be put off by the wide neck.
Tones:
Playability/Ease of Use:
Build/Design:
Value:
Street:
$1,900 base price with custom hardshell case
Soaring and Dirty
Plugged into a Fender Deluxe, the Forty-Four shines. The lone pickup, which is
designed exclusively for Island, is patterned
to some extent on the “Hershey Bar”
pickup found on the original Harmony.
I didn’t have a vintage H44 at hand for
sound comparison, but the new pickup
does have a decidedly old-school flavor. It
is gorgeously clean, with abundant clarity
and detail, and is very sensitive to nuances
in playing. The tone knob has a wide and
useful sweep. Rolled back completely, the
pickup sounds much like a jazz box, and
at the other end of the spectrum it has a
sweetly cutting timbre.
Given the wide string spacing, it was
only natural to try some fingerpicking on
the Forty-Four, and when subjected to some
basic Travis picking in the lower quarters, it
returns the favor with a rich snap and notes
that ring brilliantly. Like old Harmonies,
the guitar has a rude side, too. And when
you dig in with a plectrum for a traditional
blues solo, it responds with an aggressive
but not strident bark.
It seemed natural to channel Marc Ribot
on the Forty-Four, so I played a transcription
of the unaccompanied “St. James
Infirmary,” on which Ribot tunes down his
Harmony by two whole-steps. A lot of guitars
would sound muddy tuned this low, but
the Forty-Four retained its vibrant character.
The Verdict
In the Forty-Four, Delisle pays a respectful
tribute to a classic bargain guitar by taking
the best parts of that template in smart new
directions. It’s the perfect instrument for
electric fingerpicking, and its lone pickup
delivers a wide range of tones that will work
for everything from bebop to swamp rock.
With a base price of $1,900, this handmade
boutique guitar is also less expensive than
many factory-made instruments, and while
not cheap, it’s not bad for a guitar that’s
more than a little unique in terms of sound
and style.
Luthier Dave Helmer shows you how to cure buzzy strings, bad intonation, gnarly frets, high action, and other common troubles with off-the-shelf axes.
Guitars are the best. We love them. It’s fun to fall in love with a guitar at a store, buy it, and proudly bring it home. But we’ve all been there … where after a month that new guitar is just not playing as good as it was before. As guitar players, we know what feels good and what feels bad when it comes to playability. Maybe you have setup preferences that you like on all your guitars, or maybe you want to experiment with changes to your setup?
With a few tools, you can perform a handful of tasks that will make your new axe play better and stay in tune. This article is for folks who already know how to tighten loose parts, raise and lower string saddles or bridges, and adjust their truss rods—though I’ll share a tip on how to check it with even more accuracy.
Is that big bulky stock nut uncomfortable on your hand? Let’s trim it down and reshape it. If the action feels high and the neck looks straight, I’ll show you how to lower the action. And haven’t we all swapped out pickups and wondered, “Do they really sound better, or do I think that just because they’re new?” Before you swap your pickups, I’ll share some pickup-height measurements that might make you change your mind.
But wait! There’s more. With everything feeling and playing great, does moving into the upper register start to sound out of tune? Intonation is very easy to check and adjust. When you go to vibrato or hold a note, do the frets feel “sandy”? Are the fret ends rubbing against your hand while you play? Let’s flush and polish those up.
To be clear, we’re not swapping out anything on your new guitar: We’re simply refining the setup. Be sure to go online to see eight videos I made showing various processes covered in this story.
Begin the Beguine
There is an order of operations for best results. Neck relief is the first item to dial in, followed by getting the nut slots cut to the proper depth. After that, setting your string and pickup heights is in order. The final step is setting intonation.
Fret polishing is its own event and can happen anytime between string changes. Getting the frets feeling comfortable and well-polished will take some time and attention. You’ll also need some specialized tools as well as some that can be found in most households. Check the box for my list.
Tools You’ll Need
All of the specialized tools in this list are available through online suppliers, including StewMac and Amazon.
6" Ruler with measures in 64ths
String action gauge [Photo 1]
Miscellaneous screwdrivers
Allen wrenches
Radius blocks
Understring radius gauges (with the radius on the bottom and the top)
Fret-end dressing file
Micro-Mesh sticks [Photo 2]
Tape (low tack)
Cotton swabs
Paper towels (blue shop towels preferred)
Clean cotton rags
Nut files [Photo 3]
Stikit sandpaper
Tri-Flow lubricant
Capo
Feeler gauges
Simichrome polish
Polishing the Frets
Let’s start with the most Zen of these tasks: fret polishing.
Tape off the fretboard using low-tack tape, exposing only the frets. De-tack each piece of tape on your clothing or maybe a rag—I use my jeans or my sweatshirt. Making it less sticky helps prevent pulling finish off a maple fretboard or the neck. Taping the fretboard also prevents putting any cross-grain scratches into it while you file and polish. You can choose to tape off the entire fretboard or work your way down one fret at a time. Dealer’s choice.
One thing to note about tape, any tape: Even when you de-tack it, you do not want to leave it on overnight. If that happens, rub the tape with your finger, which will break the surface tension. Then carefully pull the tape off from a corner, making sure you’re pulling it off at an angle and not at a straight line with the fretboard edge.
Photo 4
Every fret end has a small burr on the corner from the initial fret job. The fret-end dressing file has a non-marring smooth side for rounding the fret end, and a safe square edge for getting into the corner of the fret end. So, take the fret-end dressing file, use the squared off-side, and file both corners of the fret end [Photo 4].
How to Polish Frets
Here’s how easy it is to polish and smooth frets.
Photo 5
One or two strokes is all you’ll need. Then, using the non-marring side of the file, slightly round off the fret ends. [Photo 5].
Photo 6
With the file positioned vertically, file downward to make the fret end flush with the edge of the fretboard [Photo 6].
Photo 7
For a nice, rounded-off look, polish the frets using the same rounding motion from the previous step, working through all three grits of the Micro-Mesh stick [Photo 7].
Photos 8 (top) & 9 (bottom)
Then, polish both the sides and the top of the frets [Photos 8 and 9]. Using a soft cloth and Simichrome, buff every fret. This will give you a great shine and help prevent oxidation. Now it’s time to remove the tape and condition the fingerboard if it needs it.
Note: Every fret has two fret ends to clean up and polish along with the fret itself. This is a fair amount of handwork. If you’ve never done it, you will get tired and need a break. Take that break. Take multiple breaks. Let the process take however long it requires without rushing. If you’re new, do all the fret polishing over a weekend or a few days. It should be fun, not painful. If it is difficult, call your local luthier and hire them to do it for you.
Adjusting Neck Relief
Neck relief refers to the slight amount of concave bowing intentionally created in the neck of a guitar or bass by adjusting the truss rod. For the safety of the guitar, be sure to slack the strings before doing any adjustments to the truss rod. Neither you nor your guitar needs to be tense during this process.
Photo 10
Before whipping out an Allen wrench for the truss rod, start by sight-checking the neck’s straightness. You can sight the neck with the guitar on its back, but I like to put it on edge and look at it that way. It’s easier to see how much curve there is when the guitar is on its side. I feel like gravity plays tricks on my eyes when I sight the neck with the guitar on its back. When I play the guitar, it’s on its side anyway, so looking at it from this vantage point is best [Photo 10].
Photo 11
Tune the guitar to pitch, put a capo on the first fret, and press fret 15 with your left hand. With your right hand, take a feeler gauge and check the gap at frets 7 through 9 (left-handed players, flip your hands around) [Photo 11].
From the top of the fret to the bottom of the string, the gap is usually anywhere from .003" to .012", depending on the feel you are going for. The feeler gauge should fit just between the top of the fret and the bottom of the string. The string shouldn’t move. This will tell you how much “relief” is in the neck. If you find this challenging, keep going—this will take some practice.
When dialing in the relief, I go back and forth between adjusting the truss rod and the string action. Getting the strings low and playing clean on a budget axe can be a challenge. Usually the fretwork isn’t that great, and in the upper register the frets can be unlevel, causing buzzes and clanks. If you need to raise the string action to get the notes to play clean, some fret leveling may be in order. (For more on fret leveling, go online to our article “About Fret Leveling,” from the December 2007 issue.) For good energy transfer, the neck should be as straight as possible. If the neck is straight and the frets are not level, the strings will buzz with low action.
In general, the flatter the radius on the fretboard, the straighter you can get the neck with the truss rod adjustment. On a fretboard with a 12" radius, you should be able to get .005" relief, and on a vintage 7.25" radius board you may need as much as .014" relief. The only way to get better at checking and setting relief is practice.
Refining the Nut
String buzzes, pinging noises when you tune, strings sticking in the slots, and too much string motion in the nut slots are all indicators of trouble. Before getting out the sandpaper and Micro-Mesh sticks, be sure you know if your guitar’s nut is TUSQ or bone. TUSQ is softer, so you should leave TUSQ nut slots a little higher. This leaves room for the TUSQ to wear without causing buzzing on the first fret. With bone, you can cut the slots lower, because it holds up to string wear.
How to Shape Your Guitar's Nut
Watch as Dave Helmer sands down the back half of a nut and creates a smooth finish.
The back side of the nut is usually very bulky and could often stand to lose some material to be more comfortable on your hand. So, let’s start there. Tape off the neck and headstock around the nut using a few layers of tape to protect the headstock face and fretboard. Then, slack the strings and pull them to either side of the nut.
Photo 12
Sand a bevel into the backside—the side closest to the headstock—of the nut using P320 and P400 grit Stikit sandpaper on a flat sanding stick. The bevel should start at the back of the nut and come forward about one-third to one-half the thickness of the nut [Photo 12]. Use P320 for most of the sanding and switch to P400 for the last 5 to 10 strokes.
Photo 13
Next, take a fresh Micro-Mesh stick and work through the various grits to buff/round over the bevel you’ve sanded into back of the nut [Photo 13], so it looks and feels good.
Photos 14 (left) & 15 (right)
TUSQ nuts are often tall, and the strings sit deep in the slots. Wound strings require 50 percent of the diameter of the string to sit in the nut slot, with the other 50 percent above the top of the nut surface. The plain strings should be flush with the top of the nut. Take a look at the wrong appearance [Photo 14] and the correct look [Photo 15] for properly seated strings.
How to Sand Your Guitar's Nut
Our luthier shows you how to use a radius block and sand down a nut.
Photo 16
Use a radius block that matches the radius of your fretboard. With P320 and P400 grit Stikit sandpapers, use mild pressure to sand down the top of the nut. Sand a bit and check your progress by setting the strings in the slots and putting a little tension on them. Tuning to pitch isn’t necessary. Use the P320 for most of the sanding, and switch to P400 when you are close to the 50/50 height for the wound strings. The radius block sanding will leave a flat, sharp edge on each side of the TUSQ nut [Photo 16]. To round over the sharp edge, use the sanding block and Micro-Mesh stick.
Use the coarse grit of a Micro-Mesh stick to round over and blend the bevel from the back into the top of the nut. Work through the grit gauges until it’s smooth. There is a fine balance between the bevel at the back of the nut and the top radius of the nut. Go back and forth between the two steps to get a nice, finished look and a nut that functions at optimal levels.
… And Refining the Nut Slots
Nut height is the distance from the top of the first fret to the bottom of the string. A good height on the wound strings is about .020", and for the plain strings about .015". Measuring this gap with a feeler gauge can be tricky because of the fretboard radius. Many repair folks do this by eye and feel, based on experience. It takes some practice. A good check: At pitch, fret the third fret and check for a small gap between the string and the top of the first fret.
How to Widen Your Guitar's Nut Slots
A diamond file can make quick work of deepening and widening nut slots.
Photo 17
The bottom of the string should be sitting on the bottom of the front half of the nut slot [Photo 17]. File down each nut slot to its proper depth using the corresponding nut file. There are diamond nut files on the market in multiple sizes to accommodate many string gauges. Make sure to keep your strokes straight. The standard-toothed files have less sizes and usually require rolling them from side to side to get a well-fit string.
Next, using a proper-sized file, round over the bottom back half of the nut slots down, toward the face of the headstock and away from the strings. This will allow the strings to move freely during tuning or bending, while still having support from the front half of the slot.
How to File D and G String Slots on Guitar
The D and G nut slots require special attention on 3x3-style headstock configurations.
Photo 18
On guitars with 3x3 headstock configurations, the D and G strings need the back half of the slots feathered out away from the center, so the string has a direct path to the tuner post. Using a file that is one size bigger than the string and rolling it side to side on the back of the nut slot will give the string a straight path to the tuner post. Photo 18 is my illustration showing which slots need feathering.
Additionally, use pencil lead to lubricate the slots. Just get in there with the point of a pencil and mark the slot with its graphite. You might also put a drop of Tri-Flow on the front of the string tree. Tri-Flow will run down the string, so take a cotton swab or cloth to clean up any excess. Tri-Flow has Teflon in it, so you don’t need much.
Adjusting String Action
First, find your string height by measuring the string action at the 17th fret on a Fender-style guitar and at the 15th fret on a Gibson-style instrument.On electric guitars, action can range from 3/64" to 3/32", depending on the player’s comfort. My preferences are 1/16" on the treble side and 5/64"on the bass side on both Fender- and Gibson-style guitars measured at the appropriate fret.
How to Adjust Guitar Action
Here’s a look at how our author adjusts the action.
Photo 19
Always loosen the string tension before making action adjustments. This will save wear and tear on the small bridge components. Take either a 6" ruler or a string action gauge and set it on the frets. Measure from the top of the fret to the bottom of the string [Photo 19].
If the action is high, you will lower that string’s saddle or that side of the bridge. If it is low, you will raise it. Make sure the individual saddles are sitting square and upright to the face of the bridge. You do not want them sitting at an angle or leaning over. This will cause buzzing.
Photo 20
The bottom of the strings should match the radius of the fretboard when measured with an understring radius gauge [Photo 20]. Start your adjustment with the outside strings, working toward the center. On Fender-style guitars, set the two outside strings to the height you want and have the middle four strings a bit higher than that. Bring the gauge up from underneath and just touch the two outside strings. Then, bring the strings down a little at a time until the radius matches.
On a Gibson-style Tune-o-matic, the saddles are not individually adjustable. So, if the radius doesn’t match, the saddles will need to be filed. To do this, I recommend using toothed nut files and a rolling side-to-side motion. Do a little work and check your progress. Remember to slack your strings when adjusting the saddle or bridge up or down.
Changing Pickup Height
Photo 21
Finally, let’s take a look at pickup-height adjustment. First, to check pickup height, use the two outside strings again. Press the top wound string on the last fret and measure the distance from the top of the pole piece to the bottom of the string [Photo 21]. This distance can range from 3/64" to 1/8". My preferences are 1/16" on the treble side and 5/64" on the bass side.
Adjusting Guitar Pickup Height
Dave Helmer walks you through the process of adjusting the height of your guitar’s pickups.
On most styles of pickups, there are height adjustment screws on either side of the pickup to raise or lower it. The closer the pickup gets to the strings, the more present string frequencies become. If you get too close, the magnetic pull can affect the string’s vibration and you may hear some strange sounds as you go into the upper register.
On Strats, the neck pickup is regularly set too close, and at the 12th fret and above, the low E and A can sound choked, honky, and not clear. Lowering the neck pickup with a screwdriver usually solves this issue.
Setting Intonation
Photo 22
If you can’t get your guitar accurately in tune, you might need to check its intonation. Adjust all saddles as far back as possible so every string will play flat at the 12th fret. You will adjust the saddles forward, gradually making the octave play sharper until it’s in tune with the open string [Photo 22].
Adjust Your Guitar's Intonation
With a tuner and a screwdriver, Dave Helmer shows you how to adjust your guitar’s intonation.
Depending on your vibrato style, experiment with intonating the plain strings slightly flat. Use your ear and do what sounds good. Sometimes, the plain strings can have perfect intonation, but playing with vibrato can make them sound sharp.
To fine-tune intonation, the individual bridge saddles must be adjustable. Once the intonation is set, recheck the string radius using the understring radius gauge and adjust as needed. The radius can change as the saddles come forward during intonation.
Tri-Flow is great for lubricating saddle parts. Put a small drop on the saddle-height adjustment screws and capillary action will suck it in. Adjust the saddle up and down a few times to coat the threads. Clean up any excess with a cotton swab or cloth. Put a drop or two onto a cotton swab and apply the Tri-Flow to the top of each saddle where the string rests. This will help strings move freely during tuning and after any bends or vibrato.
And that’s it! For a relatively small investment in tools and time, you’re now ready to supercharge your new guitar—and maybe your long-treasured axes, too.