Simple setup, wild rocking tones and impeccable build quality are the trademarks of the BC Audio Amplifier No. 7
Download Example 1 Epiphone Sheraton with Tom Holmes PAFs. Amp settings: Presence - noon, Bright Volume - full, Normal Volume - noon | |
Download Example 2 Same Sheraton. Amp settings: Bright Volume - off, Normal Volume - full | |
Download Example 3 2008 Fender Strat with Sheptone singlecoils. Amp settings: Presence - 2 o'clock, Bright Volume - noon, Normal Volume - noon | |
All clips were recorded with Shure SM57 directly into a Chandler LTD mic pre with no EQ and recorded on a Pro Tools HD3 Accel rig. |
No. 7
Amplifier No. 7 is the flagship model from BC Audio, built by designer and award-winning guitarist Bruce Clement. Rather than basing the design off an existing vintage amp, the No.7 is referred to as a “hand-made, all-tube, non-clone guitar amp.” The amp runs either a pair of 6V6s for 15 watts, or 5881s for 25 watts. The reviewed amp came with EH 6V6s. Rather than the typical 12AX7 preamp tubes, it uses a pair of 6SL7 Octal tubes. It’s also tube rectified with a NOS 5Y3 rectifier tube, which brings the total tube count on the amp to five. Since the amp is built inside the ammo box you need to open it up to access the controls, which is as easy as opening, well, an ammo box! Just lift up the side latch and it swings up to the left to reveal all of the controls, as well as inputs and outputs— everything is on the front panel. You can choose to keep the lid connected, or detach it by sliding it off the hinge, which is clever and handy. The layout couldn’t be much simpler. Starting on the left is a standard EIC power inlet followed by a red square power indicator. To the right of the power light is a 3-way, heavy-duty toggle switch where the down position is off, middle is standby and top is on. After the toggle is a standard 1/4" speaker jack, followed by the only three knobs on the amp: Presence, Bright Volume and Normal Volume. At the right end is the single guitar 1/4" input jack. That’s it.
Opening up the amp to check out the guts, I found something you don’t see very often these days: true point-to-point construction. No turret board, no PCB, no nothing. Just perfectly laid out components connected directly to each other at right angles and with ridiculous attention to detail. It all started making sense now: Army ammo box, Mil-spec wiring … hmm. It’s definitely a theme and a real testament to perfection and simplicity. This particular No.7 is actually serial number 1, the first one built, and it is signed and dated by Mr. Clement right there on the inside of the chassis. The chassis is solid as a rock and everything soldered or bolted to it is pure, high-quality stuff. All of this is beautiful and interesting to look at and certainly something to appreciate, but it all comes down to the tone. What about the tone?
In Play
I didn’t have my old basketweave 4x12 available at the time, so instead I plugged the No. 7 into a Krank 1x12 loaded with an Eminence Governor. With two 6V6s it pushes out a loud 15 watts, as there is no master volume. As the manual says, in order to get this thing to distort you gotta crank it. ‘Nuff said. I plugged my Epiphone Sheraton loaded with Tom Holmes PAFs directly in and cranked the Bright Volume up all the way, Presence set at noon. Right there in front of me came a whollop and kerrang that I’ve never experienced from a little 6V6 amp. To me, 6V6s are a great tube but traditionally suffer from a flubby bottom end. In this amp’s case there was none of that, just a pure and gorgeous saturated tone that reminded me of a mix of a Superlead and an AC30. To say that the tone was sweet would be doing it a disservice. I can’t put my finger on it, but it’s like the amp just blew the guitar up without adding anything but good stuff to it: superb, thick power tube gain with no artifacts or anything else getting in the way, and a pick attack that was downright explosive. It totally felt like a 100-watt amp with all the headroom you’d ever need, just by rolling back the guitar’s volume. The sustain was ridiculous, and along with the Sheraton it bloomed into a gorgeous feedback that was perfectly musical. It felt like a magic blend of muscle, tone and pure rock and roll.
The No. 7 is set up like a 4-input Marshall that’s been bridged internally in that you can blend both the Bright and Normal Volumes together to create a wide variety of tones. Since there is no tone stack, you’re left with a single Presence adjustment to vary it from “browner” tones to something with a good deal of teeth. Another thing is those Octal tubes. I’ve found that many lower-powered designs that use 12AX7s tend to be a bit buzzy. The 6SL7s add a girthy and thick element that sounds robust and less like a gnat stuck in your ear. Hey, I like 12AX7s just like the rest of us, but there is definitely a special quality to the 6SL7s.
Keeping the Epiphone plugged in, I pulled back the Bright volume all the way and cranked the Normal Volume. This tone is similar to the Normal channel on a Marshall Superlead … a bit darker and less aggressive. This isn’t a bad thing, just another tonal variety built in rather than a treble, middle, bass setup. I was treated to a thick, wailing tone on the neck pickup and a great, blooming sound. A little less edge at first, but I pushed the Presence up to nearly full and it brought out more AC30-like chime to the tone. Beautiful rock and roll. Moving on, I plugged in my ’08 Fender Strat and dimed every control. Rolling the Strat’s volume back while in the neck pickup setting conjured tones similar to Hendrix’s cleaner sounds, all the while threatening a serious sonic assault with a roll up of the guitar’s volume knob. I backed off both amp volumes to around noon and was able to pull up some fantastic clean and semi-clean/dirty tones. The thing that blew me away was that at every setting the amp had a presence about it that felt both familiar and new at the same time. It’s like having a handful of your favorite classic tube amps at your fingertips but still hearing something new and fresh. This is an amp that you can play for hours and never get bored with. I must have played straight for three hours before I took a break.
No doubt there are a lot of players that believe you need more bells and whistles to make an amp sound good, but the No. 7 proves you need nothing more than three knobs to make it work. Honestly, if the Presence were fixed at noon and there were no Normal Volume, this amp would still produce more nuance and tone than most amps I’ve played and I’d never miss not having more to twiddle with. It wakes up your guitars and exposes them for what they are, which was refreshing to my ears. I could really hear the qualities of my Les Pauls, Strats, Danelectros and Teles so clearly it made me wonder why I’d ever need anything else. Sure there’s no FX loop, channel switching or boost, but it never came up as an issue. And, if you’re a pedal freak, you’ve got nothing to worry about as this amp takes them like a schooled pro. I ran a variety of boxes ranging from a Mutron Octave Divider to a Hartman Octave Fuzz to an old Boss SD-1 with great results. The No. 7 handles pedals just like guitars— it lets their quality shine through. I ain’t Eric Johnson, but there was a minute there where I could almost tell what type of battery was in the pedals!
The Bomb
Reviewing amps is tough these days. With so many builders out there making new designs as well as updated or revised versions of classics, we truly are experiencing a renaissance. It takes a lot to stand out above the others and proclaim something is “better.” Better is also subjective, as we all know. That said, this reviewer places the No. 7 firmly in the “Better” category, if not the “Best.” It just does everything I would ever ask of an amp, and it does it with style, grace and total rock and roll abandon. Oh yeah, one final note before I go; if ammo boxes aren’t your style just contact BC Audio and they can get you hooked up with a rackmount kit so you can put it in your refrigerator rack. Ladies and gentlemen, we have a winner!
Buy if...
you want an uncompromising pure rock and roll tone in an inventive package.
Skip if...
you gotta have bells and whistles to make you feel good about the purchase price.
Rating...
MSRP $1795 - Audio Direct- bcaudio.com |
The idiosyncratic, Summer of Love-era Musicraft Messenger had a short-lived run and some unusual appointments, but still has some appreciators out there.
Funky, mysterious, and rare as hen’s teeth, the Musicraft Messenger is a far-out vintage guitar that emerged in the Summer of Love and, like so many heady ideas at the time, didn’t last too much longer.
The brainchild of Bert Casey and Arnold Curtis, Musicraft was a short-lived endeavor, beginning in San Francisco in 1967 and ending soon thereafter in Astoria, Oregon. Plans to expand their manufacturing in the new locale seemed to have fizzled out almost as soon as they started.
Until its untimely end, Musicraft made roughly 250 Messengers in various configurations: the mono-output Messenger and the flagship Messenger Stereophonic, both of which could come with the “Tone Messer” upgrade, a built-in distortion/fuzz circuit. The company’s first catalog also featured a Messenger Bass, a wireless transmitter/receiver, and various models of its Messenger Envoy amplifier, very few of which have survived, if many were ever made at all.
“To this day, even fans will sometimes call the decision to use DeArmonds the Messenger’s ‘Achilles’ heel.’”
Upon its release, the Messenger was a mix of futuristic concepts and DeArmond single-coil pickups that were more likely to be found on budget instruments than pricier guitars such as these. The Messengers often featured soapbar-style DeArmonds, though some sported a diamond grille. (To this day, even fans will sometimes call the decision to use DeArmonds the Messenger’s “Achilles’ heel.”) The Stereophonic model, like the one featured in this edition of Vintage Vault, could be plugged into a single amplifier as normal, or you could split the bridge and neck pickup outputs to two separate amps.
One of the beloved hallmarks of the guitars are their magnesium-aluminum alloy necks, which continue as a center block straight through the tailpiece, making the guitars relatively lightweight and virtually immune to neck warping, while enhancing their playability. Thanks to the strength of that metal-neck design, there’s no need for a thick heel where it meets the body, granting unprecedented access to the higher end of the fretboard.
This Stereophonic model could be plugged into a single amplifier as normal, or you could split the bridge and neck pickup outputs to two separate amps.
The neck was apparently also tuned to have a resonant frequency of 440 Hz, which, in all honesty, may be some of that 1967 “whoa, man” marketing continuing on through our modern-day guitar discourse, where this fact is still widely repeated on forums and in YouTube videos. (As one guitar aficionado to the next, what does this even mean in practice? Would an inaudible vibration at that frequency have any effect at all on the tone of the guitar?)
In any event, the combination of that metal center block—resonant frequency or not—the apple-shaped hollow wooden body of the guitar, and the cat’s-eye-style “f-holes” did make it prone to gnarly fits of feedback, especially if you engaged the Tone Messer fuzz and blasted it all through the high-gain amp stacks favored by the era’s hard rockers.
The most famous devotee of the Messenger was Grand Funk Railroad’s Mark Farner, who used the guitar—and its Tone Messer circuitry—extensively on the group’s string of best-selling records and in their defining live shows, like the Atlanta Pop Festival 1970 and their sold-out run at New York’s Shea Stadium in 1971. But even Farner had some misgivings.
The Messengers often featured soapbar-style DeArmonds, though some sported a diamond grille.
In a 2009 interview, he talked about his first test-run of the guitar: “After I stuffed it full of foam and put masking tape over the f-holes to stop that squeal, I said, ‘I like it.’” He bought it for $200, on a $25-per-pop installment plan, a steal even at the time. (He also made it over with a psychedelic paint job, befitting the era, and experimented with different pickups over the years.)
When these guitars were new in 1967, the Messenger Stereophonic in morning sunburst, midnight sunburst, or mojo red would have run you $340. By 1968, new stereo models started at $469.50. Recent years have seen prices for vintage models steadily increase, as the joy of this rarity continues to thrill players and collectors. Ten years ago, you could still get them for about $1,500, but now prices range from $3,000 to $6,000, depending on condition.
Our Vintage Vault pick today is listed on Reverb by Chicago’s own SS Vintage. Given that it’s the stereo model, in very good condition, and includes the Tone Messer upgrade, its asking price of $5,495 is near the top-end for these guitars today, but within the usual range. To those readers who appreciate the vintage vibe but don’t want the vintage price tag, Eastwood Guitars offers modern reissues, and eagle-eyed buyers can also find some very rare but less expensive vintage MIJ clones made in the late ’60s and early ’70s.
Sources: Reverb listing from SS Vintage, Reverb Price Guide sales data, Musicraft July 1, 1967 Price Schedule, 1968 Musicraft Catalog, Chicago Music Exchange’s “Uncovering The Secret Sounds of the 1967 Musicraft Messenger Guitar,” MusicPickups.com article on the Messenger.Single-coils and humbuckers aren’t the only game in town anymore. From hybrid to hexaphonic, Joe Naylor, Pete Roe, and Chris Mills are thinking outside the bobbin to bring guitarists new sonic possibilities.
Electric guitar pickups weren’t necessarily supposed to turn out the way they did. We know the dominant models of single-coils and humbuckers—from P-90s to PAFs—as the natural and correct forms of the technology. But the history of the 6-string pickup tells a different story. They were mostly experiments gone right, executed with whatever materials were cheapest and closest at hand. Wartime embargos had as much influence on the development of the electric guitar pickup as did any ideas of function, tone, or sonic quality—maybe more so.
Still, we think we know what pickups should sound and look like. Lucky for us, there have always been plenty of pickup builders who aren’t so convinced. These are the makers who devised the ceramic-magnet pickup, gold-foils, and active, high-gain pickups. In 2025, nearly 100 years after the first pickup bestowed upon a humble lap-steel guitar the power to blast our ears with soundwaves, there’s no shortage of free-thinking, independent wire-winders coming up with new ways to translate vibrating steel strings into thrilling music.
Joe Naylor, Chris Mills, and Pete Roe are three of them. As the creative mind behind Reverend Guitars, Naylor developed the Railhammer pickup, which combines both rail and pole-piece design. Mills, in Pennsylvania, builds his own ZUZU guitars with wildly shaped, custom-designed pickups. And in the U.K., Roe developed his own line of hexaphonic pickups to achieve the ultimate in string separation and note definition. All three of them told us how they created their novel noisemakers.
Joe Naylor - Railhammer Pickups
Joe Naylor, pictured here, started designing Railhammers out of personal necessity: He needed a pickup that could handle both pristine cleans and crushing distortion back to back.
Like virtually all guitar players, Joe Naylor was on a personal tone quest. Based in Troy, Michigan, Naylor helped launch Reverend Guitars in 1996, and in the late ’90s, he was writing and playing music that involved both clean and distorted movements in one song. He liked his neck pickup for the clean parts, but it was too muddy for high-gain playing. He didn’t want to switch pickups, which would change the sound altogether.
He set out to design a neck pickup that could represent both ends of the spectrum with even fidelity. That led him to a unique design concept: a thin, steel rail under the three thicker, low-end strings, and three traditional pole pieces for the higher strings, both working with a bar magnet underneath. At just about a millimeter thick, rails, Naylor explains, only interact with a narrow section of the thicker strings, eliminating excess low-end information. Pole pieces, at about six millimeters in diameter, pick up a much wider and less focused window of the higher strings, which works to keep them fat and full. “If you go back and look at some of the early rail pickups—Bill Lawrence’s and things like that—the low end is very tight,” says Naylor. “It’s almost like your tone is being EQ’d perfectly, but it’s being done by the pickup itself.”
That idea formed the basis for Railhammer Pickups, which began official operations in 2012. Naylor built the first prototype in his basement, and it sounded great from the start, so he expanded the format to a bridge pickup. That worked out, too. “I decided, ‘Maybe I’m onto something here,’” says Naylor. Despite the additional engineering, Railhammers have remained passive pickups, with fairly conventional magnets—including alnico 5s and ceramics—wires, and structures. Naylor says this combines the clarity of active pickups with the “thick, organic tone” of passive pickups.
“It’s almost like your tone is being EQ’d perfectly, but it’s being done by the pickup itself.” —Joe Naylor
The biggest difficulty Naylor faced was in the physical construction of the pickups. He designed and ordered custom molds for the pickup’s bobbins, which cost a good chunk of money. But once those were in hand, the Railhammers didn’t need much fiddling. Despite their size differences, the rail and pole pieces produce level volume outputs for balanced response across all six strings.
Naylor’s formula has built a significant following among heavy-music players. Smashing Pumpkins’ Billy Corgan is a Railhammer player with several signature models; ditto Reeves Gabrels, the Cure guitarist and David Bowie collaborator. Bob Balch from Fu Manchu and Kyle Shutt from the Sword have signatures, too, and other players include Code Orange’s Reba Meyers, Gogol Bordello’s Boris Pelekh, and Voivod’s Dan “Chewy” Mongrain.
Chris Mills - ZUZU Pickups
When Chris Mills started building his own electric guitars, he decided to build his own components for them, too. He suspected that in the course of the market’s natural thinning of the product herd, plenty of exciting options had been left unrealized. He started working with non-traditional components and winding in non-traditional ways, which turned him on to the idea that things could be done differently. “I learned early on that there are all kinds of sonic worlds out there to be discovered,” says Mills.
Eventually, he zeroed in on the particular sound of a 5-way-switch Stratocaster in positions two and four: Something glassy and clear, but fatter and more dimensional. In Mills’ practice, “dimensional” refers to the varying and sometimes simultaneous sound qualities attained from, say, a finger pad versus a fingernail. “I didn’t want just one thing,” says Mills. “I wanted multiple things happening at once.”
Mills wanted something that split the difference between a humbucker’s fullness and the Strat’s plucky verve, all in clean contexts. But he didn’t want an active pickup; he wanted a passive, drop-in solution to maximize appeal. To achieve the end tone, Mills wired his bobbins in parallel to create “interposed signal processing,” a key piece of his patented design. “I found that when I [signal processed] both of them, I got too much of one particular quality, and I wanted that dimensionality that comes with two qualities simultaneously, so that was essential,” explains Mills.
Mills loved the sound of alnico 5 blade magnets, so he worked with a 3D modeling engineer to design plastic bobbins that could accommodate both the blades and the number of turns of wire he desired. This got granular—a millimeter taller, a millimeter wider—until they came out exactly right. Then came the struggle of fitting them into a humbucker cover. Some key advice from experts helped Mills save on space to make the squeeze happen.
Mills’ ZUZUbuckers don’t have the traditional pole pieces and screws of most humbuckers, so he uses the screw holes on the cover as “portholes” looking in on a luxe abalone design. And his patented “curved-coil” pickups feature a unique winding method to mix up the tonal profile while maintaining presence across all frequencies.
“I learned early on that there are all kinds of sonic worlds out there to be discovered.” —Chris Mills
Mills has also patented a single-coil pickup with a curved coil, which he developed to get a different tonal quality by changing the relative location of the poles to one another and to the bridge. Within that design is another patented design feature: reducing the number of turns at the bass end of the coil. “Pretty much every pickup maker suggests that you lower the bass end [of the pickup] to compensate for the fact that it's louder than the treble end,” says Mills. “That'll work, but doing so alters the quality and clarity of the bass end. My innovation enables you to keep the bass end up high toward the strings.”
Even Mills’ drop-in pickups tend to look fairly distinct, but his more custom designs, like his curved-coil pickup, are downright baroque. Because his designs don’t rely on typical pickup construction, there aren’t the usual visual cues, like screws popping out of a humbucker cover, or pole pieces on a single-coil pickup. (Mills does preserve a whiff of these ideals with “portholes” on his pickup covers that reveal that pickup below.) Currently, he’s excited by the abalone-shell finish inserts he’s loading on top of his ZUZUbuckers, which peek through the aforementioned portholes.
“It all comes down to the challenge that we face in this industry of having something that’s original and distinctive, and also knowing that with every choice you make, you risk alienating those who prefer a more traditional and familiar look,” says Mills.
Pete Roe - Submarine Pickups
Roe’s stick-on Submarine pickups give individual strings their own miniature pickup, each with discrete, siloed signals that can be manipulated on their own. Ever wanted to have a fuzz only on the treble strings, or an echo applied just to the low-register strings? Submarine can achieve that.
Pete Roe says that at the start, his limited amount of knowledge about guitar pickups was a kind of superpower. If he had known how hard it would be to get to where he is now, he likely wouldn’t have started. He also would’ve worked in a totally different way. But hindsight is 20/20.
Roe was working in singer-songwriter territory and looking to add some bass to his sound. He didn’t want to go down the looping path, so he stuck with octave pedals, but even these weren’t satisfactory for him. He started winding his own basic pickups, using drills, spools of wire, and magnets he’d bought off the internet. Like most other builders, he wanted to make passive pickups—he played lots of acoustic guitar, and his experiences trying to find last-minute replacement batteries for most acoustic pickups left him scarred.
Roe started building a multiphonic pickup: a unit with multiple discrete “pickups” within one housing. In traditional pickups, the vibration from the strings is converted into a voltage in the 6-string-wide coils of wire within the pickup. In multiphonic pickups, there are individual coils beneath each string. That means they’re quite tiny—Roe likens each coil to the size of a Tylenol pill. “Because you’re making stuff small, it actually works better because it’s not picking up signals from adjacent strings,” says Roe. “If you’ve got it set up correctly, there’s very, very little crosstalk.”
With his Submarine Pickups, Roe began by creating the flagship Submarine: a quick-stick pickup designed to isolate and enhance the signals of two strings. The SubPro and SubSix expanded the concept to true hexaphonic capability. Each string has a designated coil, which on the SubPro combine into four separate switchable outputs; the SubSix counts six outputs. The pickups use two mini output jacks, with triple-band male connectors to carry three signals each. Explains Roe: “If you had a two-channel output setup, you could have E, A, and D strings going to one side, and G, B, and E to the other. Or you could have E and A going to one, the middle two strings muted, and the B and E going to a different channel.” Each output has a 3-position switch, which toggles between one of two channels, or mute.
“I’m just saying there’s some unexplored territory at the beginning of the signal chain. If you start looking inside your guitar, then it opens up a world of opportunities.” —Pete Roe
This all might seem a little overly complicated, but Roe sees it as a simplification. He says when most people think about their sound, they see its origin in the guitar as fixed, only manipulatable later in the chain via pedals, amp settings, or speaker decisions. “I’m not saying that’s wrong,” says Roe. “I’m just saying there’s some unexplored territory at the beginning of the signal chain. If you start looking inside your guitar, then it opens up a world of opportunities which may or may not be useful to you. Our customers tend to be the ones who are curious and looking for something new that they can’t achieve in a different way.
“If each string has its own channel, you can start to get some really surprising effects by using those six channels as a group,” continues Roe. “You could pan the strings across the stereo field, which as an effect is really powerful. You suddenly have this really wide, panoramic guitar sound. But then when you start applying familiar effects to the strings in isolation, you can end up with some really surprising textural sounds that you just can’t achieve in any other way. You can get some very different sounds if you’re applying these distortions to strings in isolation. You can get that kind of lead guitar sound that sort of cuts through everything, this really pure, monophonic sound. That sounds very different because what you don’t get is this thing called intermodulation distortion, which is the muddiness, essentially, that you get from playing chords that are more complex than roots and fifths with a load of distortion.” And despite the powerful hardware, the pickups don’t require any soldering or labor. Using a “nanosuction” technology similar to what geckos possess, the pickups simply adhere to the guitar’s body. Submarine’s manuals provide clear instruction on how to rig up the pickups.
“An analogy I like to use is: Say you’re remixing a track,” explains Roe. “If you get the stems, you can actually do a much better job, because you can dig inside and see how the thing is put together. Essentially, Submarine is doing that to guitars. It’s allowing guitarists and producers to look inside the instrument and rebuild it from its constituent parts in new and exciting ways.”
Pearl Jam announces U.S. tour dates for April and May 2025 in support of their album Dark Matter.
In continued support of their 3x GRAMMY-nominated album Dark Matter, Pearl Jam will be touring select U.S. cities in April and May 2025.
Pearl Jam’s live dates will start in Hollywood, FL on April 24 and 26 and wrap with performances in Pittsburgh, PA on May 16 and 18. Full tour dates are listed below.
Support acts for these dates will be announced in the coming weeks.
Tickets for these concerts will be available two ways:
- A Ten Club members-only presale for all dates begins today. Only paid Ten Club members active as of 11:59 PM PT on December 4, 2024 are eligible to participate in this presale. More info at pearljam.com.
- Public tickets will be available through an Artist Presale hosted by Ticketmaster. Fans can sign up for presale access for up to five concert dates now through Tuesday, December 10 at 10 AM PT. The presale starts Friday, December 13 at 10 AM local time.
earl Jam strives to protect access to fairly priced tickets by providing the majority of tickets to Ten Club members, making tickets non-transferable as permitted, and selling approximately 10% of tickets through PJ Premium to offset increased costs. Pearl Jam continues to use all-in pricing and the ticket price shown includes service fees. Any applicable taxes will be added at checkout.
For fans unable to use their purchased tickets, Pearl Jam and Ticketmaster will offer a Fan-to-Fan Face Value Ticket Exchange for every city, starting at a later date. To sell tickets through this exchange, you must have a valid bank account or debit card in the United States. Tickets listed above face value on secondary marketplaces will be canceled. To help protect the Exchange, Pearl Jam has also chosen to make tickets for this tour mobile only and restricted from transfer. For more information about the policy issues in ticketing, visit fairticketing.com.
For more information, please visit pearljam.com.
The legendary German hard-rock guitarist deconstructs his expressive playing approach and recounts critical moments from his historic career.
This episode has three main ingredients: Shifty, Schenker, and shredding. What more do you need?
Chris Shiflett sits down with Michael Schenker, the German rock-guitar icon who helped launch his older brother Rudolf Schenker’s now-legendary band, Scorpions. Schenker was just 11 when he played his first gig with the band, and recorded on their debut LP, Lonesome Crow, when he was 16. He’s been playing a Gibson Flying V since those early days, so its only natural that both he and Shifty bust out the Vs for this occasion.
While gigging with Scorpions in Germany, Schenker met and was poached by British rockers UFO, with whom he recorded five studio records and one live release. (Schenker’s new record, released on September 20, celebrates this pivotal era with reworkings of the material from these albums with a cavalcade of high-profile guests like Axl Rose, Slash, Dee Snider, Adrian Vandenberg, and more.) On 1978’s Obsession, his last studio full-length with the band, Schenker cut the solo on “Only You Can Rock Me,” which Shifty thinks carries some of the greatest rock guitar tone of all time. Schenker details his approach to his other solos, but note-for-note recall isn’t always in the cards—he plays from a place of deep expression, which he says makes it difficult to replicate his leads.
Tune in to learn how the Flying V impacted Schenker’s vibrato, the German parallel to Page, Beck, and Clapton, and the twists and turns of his career from Scorpions, UFO, and MSG to brushes with the Rolling Stones.
Credits
Producer: Jason Shadrick
Executive Producers: Brady Sadler and Jake Brennan for Double Elvis
Engineering Support by Matt Tahaney and Matt Beaudion
Video Editor: Addison Sauvan
Graphic Design: Megan Pralle
Special thanks to Chris Peterson, Greg Nacron, and the entire Volume.com crew.