Premier Guitar features affiliate links to help support our content. We may earn a commission on any affiliated purchases.
NY Amp Show - Analog Man's New Amp and Pedals
Analog Man showed us some pedals, including their Chorus pedals, Compressor pedals, Juicer pedals, and CompROSSor pedals. Also, they showed off their new 5-watt practice amp.
For more information:
Analog Man
Analog Man showed us some pedals, including their Chorus pedals, Compressor pedals, Juicer pedals, and CompROSSor pedals. Also, they showed off their new 5-watt practice amp.
OC Pedal Co. was formed in 2024 by Santa Ana native Evan Haymond, a session ace who toured with Jack Russell of Great White in the 2010s. Not surprisingly, OC Pedal Co.’s U.S.A.-made LA HABRA Hard Clipper evokes many of the crunchy sounds from that era.
Less is More
The LA HABRA’s control panel is minimal, with just two knobs—volume and tone. There’s no gain knob, instead you get a gain switch that lets you choose between two clipping profiles. In the right position the pedal employs op-amp clipping. Set it to the left and a set of LED diodes are activated. With humbuckers, the gain switch set to LED mode, and the tone knob at 11:00, the LA HABRA produced a toothy sound that, sure enough, produced power chord sounds that sounded more than a little like Great White’s cover of “Once Bitten, Twice Shy.”
Though the lack of a gain knob may leave some players feeling limited, the tone knob is a powerful tool for shaping the characteristics of the distortion, and with the tone knob at its darkest setting, the LA HABRA still delivers ample definition. Move the tone knob up to around 3:00, though, and there’s enough clarity and treble detail to make leads sizzle. To my ears this is where the pedal shines, and bumping the tone knob all the way up (with the gain switch still set to the LED clipping mode), the sound is super aggressive without being over-saturated.
In general, with the gain switch set to LED clipping you get a high-end boost and hear and feel more compression. Op-amp clipping tames some of the highs yielding a more balanced output, which is particularly noticeable when the tone knob is set to 3:00 and above. I generally preferred the gain switch set to op-amp clipping but each clipping mode yields sounds that can work in many contexts.
The Verdict
The LA HABRA has plenty of definition for melodic parts and is tough enough for bluesy riffs. For legato shred-type playing, there were times when I wished the pedal had a little more gain. But LA HABRA has a knack for feeling amp-like, particularly in terms of dynamics and touch sensitivity—much more so than many pedals that occupy this mid- to high-mid-gain category.
The aptly named Kali distills elements of the Fortin Cali—a Plexi-inspired amp—into a 2-channel pre-amp and distortion pedal. Each channel has three gain modes—vintage, raw, and saturation—which are selectable via a mini toggle. And each mode has a very distinct vibe, which could be loosely categorized as low-end-heavy, midrangey, and high-gain-centric, respectively.
Charging right into Kali’s arms, I selected the vintage mode on Channel 1, and set the gain 2 knob to 9 o’clock. The gain 2 knob, which controls the gain level that hits the circuit’s front end, is the default gain knob for both channels. The gain 1 knob, which adds additional gain stages, only works on channel 2. But even at this modest setting, I was already into toothy distortion that was very touch-sensitive.
Wide Range of Rage
Without changing any other settings, things got significantly filthier by merely switching over to the saturation mode. And even at this lower-gain setting, the output is tailor-made for heavy rhythm in a classic metal jam. Pumping the gain 2 knob to around 3 o’clock, meanwhile, makes the Kali a very in-your-face proposition, with sounds rooted in Sunset Strip/Jose Arredondo Marshall-mod energy.
Interestingly, even though saturation mode has the most aggressive gain structure, it doesn’t feel especially compressed. It’s also the quietest of the three modes when tested across identical settings. This was especially noticeable when I switched between vintage and saturated modes at high gain 2 settings. It follows, then, that raw mode—the pure sound of the pedal without any extra gain stages and essentially the preamp only—is the loudest of the three modes.
Well Put Together, With a Bright Personality
Channel switching is handled by one of the two footswitches (the other
is for bypass) and it enables you to cascade one channel into another. In cascaded-stage mode, gain knob 1 is active and serves as a pre-gain (hence the gain 1 designation). In saturation mode, with both gain knobs at noon, switching between the channels sounds organic. Channel 2 is generally thicker and sustains bends for a tad longer. But the two channels definitely do not feel haphazardly thrown together. They are clearly cut from the same cloth.
“[It’s] a very in-your-face proposition, with sounds rooted in Sunset Strip/Jose Arredondo Marshall-mod energy."
In general, the Kali is bright, but if you need brighter, there are a pair of 3-position bright switches for each of the two channels. At low output volumes the changes offered by these bright switches are noticeable but not too dramatic. They are much more pronounced at high output volume. The active +/- EQ knobs actually have much greater impact on the Kali’s personality—particularly in the zones between 9 and 3 o’clock, where minor tweaks yield very different tonal realms.
The Verdict
The Kali comes across as a cohesive whole, yet its interactive controls and powerful EQ unlock a wide range of Plexi and modded-Plexi tones. No matter how you set it, it sounds impressive.
As the leaves change and the holiday season approaches, PG contributor Tom Butwin highlights standout pedals from the bevy of tone machines that graced shelves this year. In his first installment of Pedalmania, hear demos of the flexible Keeley Manis Overdrive, Mr. Black's DoubleTracker Stereo, the spacey new Hotone Verbera convolution reverb, and the featured-packed NUX Amp Academy Stomp.
There are more flexible means for mashing up fuzz and delay thanBenson’s Deep Sea Diver. And in a time of preposterously low-priced pedals, there are more economical methods, too. But there’s no guarantee that a more traditional and cost-conscious path will yield results as interesting—or inspirational—as those offered by the Deep Sea Diver. It’s a pedal that often serves up zigs where you seek zags—depending on your sense of adventure and creative latitude, it can feel versatile, forgiving, and full of exciting surprises.
Bathyspheric Battiness
The Deep Sea Diver was developed withJessica Dobson, who fronts the band that shares the pedal’s name—and for whom more unusual applications of the fuzz/delay equation are a sonic cornerstone. The basic architecture of the Deep Sea Diver makes a great departure point for any player keen to ply the odder corners of that stompbox formula. It’s hard to know firsthand exactly what that architecture is—Benson flipped the circuit board so that you don’t see components, but rather a stylized representation of Dobson’s face in silhouette. (For the record, the solders you can see all look exceptionally tidy).
Chris Benson says that the 3-transitor fuzz section of the circuit uses a mutant mix of the 2-transitor Tone Bender MK 1.5 and the 3-transistor Tone Bender MK 2.0 as a foundation. Dobson says she envisioned a less hectic version of the ZVEX Fuzz Factory—a relation borne out here by the gate and bias controls. The delay section, meanwhile, is built around a PT2399 chip. This is a device many builders have put to creative use in spite of first turning up in karaoke machine delays. Its sonic signature—lo-fi, hazy—can be similar to that of bucket brigade delays, but still occupies a different lane than the analog EHX Memory Man and Diamond Memory Lane devices that underpin Dobson’s rig. As a whole then, the Deep Sea Diver doesn’t really replicate any particular part of Dobson’s tone recipe as much as it adds a new color formed in the spirit of where her playing has been and where it might be going.
One Deep Sea Diver feature that is a fixture of Dobson’s tone is a delay that is situated before the fuzz—except for when it isn’t. By holding down the bypass switch while powering up, you can reverse the order of the effects. If you’ve never experimented with switching fuzz and delay, the results can be revelatory.
Submarine Flip Flops
Given how interesting it is to move between the order of effects on the Deep Sea Diver, it’s a shame that you can’t make the switch without powering off the unit. Obviously, that’s not the most complicated process, but it’s also not one you’ll attempt in the middle of a song or set. Many pedals enable effect-order switching via a toggle or alternate footswitch input. In this case, the latter possibility was difficult for good reason, as pressing and holding the footswitch activates an endlessly entertaining runaway oscillation effect.
To a passively listening bystander, a switch in fuzz/delay effects order isn’t always glaringly obvious. In a very general sense, fuzz before delay results in greater clarity, and vice versa. But on the Deep Sea Diver, situating the delay before the fuzz lends a gauzy, foggy smear around the edge of transient notes and the repeats that you feel as much as hear. Comparing the Deep Sea Diver to a bucket brigade delay and a ZVEX Fuzz Factory, you can hear why Chris Benson employed the PT2399 chip. There’s a slightly more lo-fi blur to the Deep Sea Diver’s delay signature, which, to my ears, lends extra mystery.
One Deep Sea Diver feature that is a fixture of Dobson’s tone is a delay that is situated before the fuzz—except for when it isn’t.
But it’s the fuzz section of the Deep Sea Diver that really expands its performance envelope. The gate and bias controls both have impressive range and work together pretty seamlessly to broaden the pedal’s fuzz voice. There are lots of collapsing, fractured fuzz-on-the fritz and dying-AM-radio sounds made more appealing by the smoky delay signal. You’ll find many shades of super-cool mid-1960s buzz, too. But it’s also capable of unique, punchy drive sounds that hit hard and are easy to compose with, and situate in a mix without sounding entirely unhinged. The Deep Sea Diver will happily go bonkers if that’s what you’re after though, and as you get a feel for the way the gate and bias controls interact you might not even miss the conspicuously absent gain level control—which, I venture, would complicate matters significantly.
The Verdict
I played the Deep Sea Diver next to a few different fuzz/delay combinations, and there is an audible cohesiveness in the two effects at the Benson's core. Furthermore, the resulting dovetailed fuzz/delay voices lend the Deep Sea Diver a truly individual voice at many settings. Though it falls short of mimicking the butter-smooth sustain of, say, a Big Muff and a Boss DD-5, it can still dish many rich fuzz tones in that spirit—just a bit filthier. The Deep Sea Diver is most certainly eccentric, just as its creators no doubt intended. But it’s not exclusively weird. There are plenty of sounds here for classicists, even if the Deep Sea Diver tends to beckon the player toward more unorthodox ends.
When California-based effects company Noise Engineering released their Desmodus Versio in 2020, it represented the first reverb effect in their product line, but they coined a new term for the DSP-based effect: a synthetic-tail generator. The name reflects the reality that, by definition, it doesn't create literal reverberation, as in reflections in a room, but instead builds “tails” onto an audio signal. Taxonomy aside, it was a powerful, well-received, and positively jam-packed digital unit.
The Batverb, launched earlier this year, is an evolution of Noise’s tail-generating efforts. However, it uses brand-new code programmed for Electrosmith’s Daisy Seed DSP platform. A stereo effect box that spans delightful and demented flavors of delay and reverb, the Batverb is generously featured and full of unique takes on space-making effects.
Heads or Tails
The Batverb’s main panel includes six knobs, three 3-way switches, two footswitches, and one “bat” button, which you press and hold to access alternate parameters assigned to the knobs. On the crown are input jacks for either mono or stereo performance. On the sides are MIDI in/out and expression pedal jacks. Up to 16 different presets can be saved and recalled via MIDI.
In normal operation, the knobs govern, from bottom left to bottom right, input volume, time, a suboctave chorus, an octave-up shimmer, “regen” or feedback, and a blend of dry and wet signals. When holding the bat button, those same knobs, in order, control output volume, MIDI channel selection, high-pass filter, low-pass filter, duck amount, and expression pedal parameter assignment. The focus switch changes the diffusion of the delay lines. In the left position it behaves more like a delay, while the other two settings sound and feel more like reverbs. Grit adds, in the middle and right positions, a discrete soft-clipping distortion, and duck determines the responsiveness of the feedback. In the switch’s center position, there’s no ducking. At left, feedback momentarily increases when input volume is received, then tapers off as the signal does. At right, the opposite happens, and feedback increases as the signal gets quieter.
Enter the Bat Cave
To my ears, the Batverb’s more reverb-y patches are in hall or room territory—albeit very cavernous halls or rooms. But reverb sounds created by the Batverb’s algorithms sound more authentic to me than many sought-after reverbs I’ve played. Rather than an indistinct wash of sound, the tails here give the convincing impression of your amp’s signal ricocheting around a high-ceilinged cathedral, at first coming back in clearer, sharper bursts, then melting into smeary ambience. And the handy hold feature can be engaged for infinite regeneration by tapping the footswitch, or for a specific window by pressing and holding. That double utility goes a long way toward determining whether the Batverb sounds organic or unhinged.
The sub- and up-octave content injected by the doom and shimmer knobs is more chaotic and spacious than garden-variety iterations of those effects you’ll find on many octave-based reverbs, and that’s a good thing. Like most effects generated by the Batverb, it feels like the product of thoughtful, well-considered programming.
The delay algorithm, engaged with the focus toggle at left, is pleasant and plenty usable, and it’s nice to have alongside the less predictable reverb settings. But the Batverb’s deep tweakability means you can still dial in a broad range of both standard and more marginal delay sounds. The chunky transistor-ish dirt summoned by the grit switch widens the palette further. Add in the touch-sensitive ducking (and its customizable parameters), and you’ve got a ton of ground to play with.
The Verdict
Noise Engineering created an outstanding reverb and tail generator here. Considering its steep asking price, the Batverb will be out of reach for many, but it’s obviously geared toward adventurous players and discerning producers, especially those looking for authentic, parallel universe-conjuring ambience and noise in their studio or live rigs. For these musicians, the Batverb will be more than worth the bite it takes from the bank balance.