
A view of the mic closet at Nashville’s County Q studio.
Compare notes with Nashville producer-engineer Mike Purcell, who runs down the essentials of a pro-level home-studio mic collection.
A well-rounded mic closet could take a lifetime to build. I’m constantly trying different things, but there’s always a core set of mics I come back to because they’re reliable and provide good results. Many of these mics work on a wide range of instruments. By knowing my mics, I can make a choice that’s going to enhance the sound of an instrument—especially guitar.
In this story, I’ve listed several options for each mic type covering a range of prices from low to high. A higher cost usually indicates that the quality of components and workmanship are better, leading to a more consistent product. Lower cost generally means quality control isn’t as strict and that mics may differ more from their published specs.
You’ve probably heard this before, but the three main types of mics are dynamic (or moving coil), condenser (or capacitor), and ribbon mics. Let’s work our way through each category.
Dynamic Mics
Dynamic mics are composed of a voice coil suspended in a magnet. Incoming sound moves the voice coil within the magnetic field and a current is created. This is passed through a transformer to step up the voltage, and then sent to a mic preamp.
Dynamic mics are the mainstay of live sound because of their durability and ability to be used on loud sound sources without overloading. These are desirable characteristics in the studio when we’ve got to place mics close to a flailing drummer or mike up a Marshall Super Lead 100 full stack.
Dynamic mics exhibit the following characteristics:
- They are less sensitive to transients and high frequencies (7k and up.) They capture these frequencies, but at a lower level than a condenser.
- They color the sound in the midrange between 3-5k, adding a slight bump in this area.
- On loud sound sources, they exhibit a type of mild compression or soft clipping, useful on amps, drums, and vocals.
- They are cardioid, or unidirectional, and are the most sensitive in the front with maximum rejection off the back. (There are divisions of cardioid: hyper, super, etc. In all cases, they are most sensitive at the front, with rejection off the back or sides.)
- They exhibit a proximity effect. As directional mics are placed closer to a sound source, they pick up more low end, 100 Hz and below. Dynamic mics are designed to use the proximity effect, so as they move farther from a sound source, they will sound thinner.
“Dynamic mics are the mainstay of live sound because of their durability and ability to be used on loud sound sources without overloading.”
Even though dynamics all exhibit these same general characteristics, each mic will color the sound differently. Some dynamic mics work better on drums. They have an increased low-frequency response, a dip in the lower mids, and a bump in the presence range—essentially an EQ curve that sounds good on bass drums and toms. Others may have a more pronounced bump in the upper mids, making them a great choice for guitar amplifiers. While dynamic mics are typically used for the close miking of drums and guitar amplifiers, they are also well-suited to some vocalists.
A well-rounded mic closet in a home studio that cuts four- or five-piece bands would have at least 8 to 10 dynamics. Modern production dynamic mics top out around $600, and most are under $250.
Dynamics mics to consider:
- Shure SM57 ($99 street): The most common mic in the world. It’s cheap, incredibly durable, and sonically consistent from mic to mic. It can take the highest sound pressure level (SPL) you can throw at it and work on any instrument in a pinch. It’s often used for snare drums or guitar amps. Many of Tom Petty’s vocals were recorded with an SM57.
- Shure SM58 ($99 street): The big brother to the SM57. It has a built-in pop filter/windscreen and a slightly different low-end response. There are hundreds of cheap knockoffs of the Shure SM57 and SM58. Stick with the originals and you’ll be much happier over the long run.
- Sennheiser e 609 ($99 street): An inexpensive supercardioid mic. The supercardioid pattern indicates it is much more directional than a cardioid. This can be useful when miking a snare drum, to reject sound off the sides of the mic. The e 609 also has a slightly less harsh frequency response, so can be useful on edgy or bright guitars.
- Shure Beta 52A ($199 street), Audix D6 ($199 street), AKG D112 ($229 street): These are a newer generation of dynamic mics that are designed for bass drums. Plus, they work well on toms—although Audix also makes the D4 and D2, which are tailored towards smaller drum frequencies (rack tom, floor tom). And they work well on bass amplifiers.
- Sennheiser MD 421-II ($399 street): Excellent kick and tom microphone. The frequency response of the 421 works well on drums. It’s also commonly used on guitar amps and vocals.
- Shure SM7B ($399 street): Another variation using the SM57/58 diaphragm, this mic has electronics that allow you to tailor its frequency response. The SM7 is often used in broadcast and is a go-to choice for vocals by rap and metal artists.
Side note: Many manufacturers offer a drum-mic package—a great solution if you’re starting out. These usually include several dynamics for the close mics and a few condensers for the overheads and/or hi-hat. Plus, these mics can also be used for recording other instruments.
Here are a few examples of drum packages:
- Audix FP7 ($399 street): A seven-piece mic kit, with five dynamics and two condensers. Audix also offers larger drum packages.
- Avantone PRO CDMK-8 ($899 street): This eight-piece kit includes five dynamics and three condensers.
- AKG Drum Set Premium ($2,329 street): Another eight-piece set, with five dynamics and three condensers.
Condenser Mics
Condenser mics consist of a thin, charged diaphragm suspended over a metal plate. As sounds strikes the diaphragm, it moves and causes electrons to flow through the plate. This signal is amplified by internal electronics and passed through a transformer or field-effect transistor (FET) and is sent to a mic preamp.
Condenser mics exhibit these characteristics:
- They are active devices that require a power source, most commonly provided by +48V Phantom Power.
- Some are capable of multiple polar pickup patterns: cardioid, omnidirectional, figure eight, and everything in between.
- They may include a passive attenuation device (PAD), a switchable attenuator that prevents overload when the mic is used on loud sound sources.
- They may include a switchable high-pass filter (HPF), used to roll off unwanted low-end frequencies.
- They are the most sensitive mics, making them ideal for recording quiet instruments.
- They have the widest frequency response and are good at capturing frequencies across the audible spectrum.
- They color sound less than other mics and are good when you want to accurately capture the timbre of an instrument.
Condenser mics are divided into two categories: small diaphragm condensers (SDC) and large diaphragm condensers (LDC). SDCs have a diaphragm of less than 1" and tend to be more responsive to transients and high frequencies. Their off-axis response is also more even.
LDCs have a 1" or greater diaphragm. They sound fuller, but off-axis mic response can be uneven. LDCs, because of their overall size, can be harder to position in tight miking situations.
“Because of their sensitivity and wide frequency response, condenser mics are used for drum overheads and ambience, acoustic stringed instruments, piano, ensembles, amplifiers, and vocals.”
Matched microphone sets require that the frequency response and sensitivity of the two microphones are very similar. This allows them to record a balanced stereo image. So, a well-rounded mic closet will have a matched set of SDCs and LDCs, and a few assorted condensers for other purposes.
SDCs to consider:
- Rode NT5 ($219 single/$429 pair street): Rode is an Australian manufacturer that makes quality products at affordable prices. I’ve been impressed with all their equipment, and the NT5 is no exception.
- Shure SM81 ($399 street): A good, durable utility mic. Inexpensive. Not as open sounding as other SDCs. I use these for snare bottoms and hi-hats. They have a PAD and HPF.
- Warm Audio WA84 ($399 single/$749 pair street): Warm Audio is a relative newcomer to the pro audio world. They’ve been making reproductions of classic gear and offering them at lower prices. In general, I’ve been impressed with the quality of their products. These PAD-equipped mics are their version of the KM-184, at half the cost.
- AKG C451 B ($639 single/$1,395 pair street): Very responsive to transients and can take high SPL. These PAD and HPF mics yield an edgier sound. I love these on mandolin or banjo.
- Miktek C5 ($699 /$1,399 pair street): These mics include a switchable omni capsule, allowing for cardioid and omnidirectional use for spaced pair miking.
- Neumann KM184 ($849 single/$1,595 pair street): Smooth sounding all-around mic with an articulate and defined high-frequency response. One of my favorite go-to mics when I need a stereo recording of an instrument.
LDCs to consider:
With LDCs, manufacturers have families of mics that use the same basic components, but the higher-end mics will offer pattern selection or other features. Within the family, the sound will be similar. Examples are the AKG C214 and C414, and the Shure KSM32 and KSM44.
- Rode NT1000 ($329 street): I am a huge fan of Rode, and the NT1000 routinely beats out more expensive mics for vocals. This cardioid mic is solidly built and big sounding without harshness..
- AKG C214 ($465 street): The little brother to the AKG C414, this cardioid-only example with a PAD and HPF exhibits the same general frequency response, but it doesn’t have all the features of the 414.
- Audio Technica AT4033A ($399 street): One of my favorite inexpensive mics, the 4033 has a pleasant defined midrange and clarity that brings instruments through the mix. These may not be good when trying to capture extended low frequencies. Audio-Technica calls this cardioid mic a medium-diaphragm condenser.
- Miktek C1 and C7e ($599 and $899 street): Miktek is a Nashville-based manufacturer that has developed a line of mics that perform far outside their price class. The C1 has a PAD, HPF, and is cardioid only, while the C7e is multipattern.
- Neumann TLM 103 ($1,195 street): The TLM 103 is a smaller footprint package that utilizes Neumann’s classic U 87 capsule and transformer-less circuitry at a more affordable price. These sound great on vocals and acoustic stringed instruments, if you’re looking for a bigger sound.
- AKG C414 ($1,279 street): The 414 is another industry standard found in many studios. Based on the classic AKG CK12 capsule, the 414 has a wide frequency response. It is bright and present and can sound amazing on some singers and overly bright on others. It works well on pianos and acoustic guitars where you need a sheen on them.
- Neumann U 87 Ai ($3,695 street): The U 87 is a flagship standard that you can find in almost any studio. Multipattern select, HPF and PAD equipped, it’s got a fat low end, smooth high frequencies without harshness, and a thick, musical midrange. An incredibly flexible mic with excellent fidelity, it’s got a price tag to match its functionality. I’ve used these on toms for a huge sound, but you have to really trust the drummer if you’re putting this mic in range of their sticks
Ribbon Mics
Ribbon mics function by suspending a very thin conductive metal strip between two magnets. Sound waves strike the metal strip, causing it to vibrate. The vibration in the magnetic field creates a current in the magnets. This is sent through a transformer, and then the signal is sent to a mic preamp.
“Never run +48V phantom power to a ribbon mic. While most modern ribbons are phantom safe, it can destroy vintage ribbon mics.”
A good mic closet should have several ribbon mics, and possibly more depending on the style of production. Ribbon mics have seen a resurgence over the past 20 years and there is a wide variety available, ranging from $200 to $1,500 and more. Ribbons are used on guitar amps, as drum overhead or room mics, and on horns, acoustic guitars, percussion, and vocals.
Ribbon mics exhibit these characteristics:
- The thin ribbon allows them to be very sensitive to transients.
- They color the sound. They are warm sounding and add character.
- They are the least sensitive type of mic and ill-suited for quiet sound sources.
- They’re very fragile. A puff of wind (or the air coming out of a kick drum) can damage the mic.
- They are bi-directional/figure eight. They pick up sound from the front and back of the mic at the same level. Exceptions exist, like the Beyerdynamic M 160.
- Caution: Never run +48V phantom power to a ribbon mic. While most modern ribbons are phantom safe, it can destroy vintage ribbon mics. (Once again, there are exceptions. Active ribbon mics, like the AEA N22 Nuvo, exist. These do have internal amplification similar to a condenser and require phantom power.)
Ribbon mics to consider:
- Pinnacle Microphones Fat Top ($229/$519 pair street): The Fat Top is a current iteration of the original Cascade Fat Head. I’ve used Fat Heads for years. They’re wonderful on guitar amps and percussion.
- Stager SR-66/SR-2N ($699/$649 street): Stager Microphones is a small boutique operation in Nashville. They use neodymium magnets in these models, for increased magnetism in a lighter package. The transformers are hand-wound and designed to get the best transfer of sound from ribbon to mic preamp. The SR-66 is a long-ribbon package, offering a flatter frequency response. The SR-2N is a midrange-forward short-ribbon design.
- Coles Electroacoustics 4038 ($1,485 street): The Coles 4038 is designed by the British Broadcasting Corporation in the 1950s and the tech specs have never changed. A lot of work went into engineering this mic. It has a flat frequency response up to 15k and is very responsive to transients.
- Royer R-121 ($1,499 street): Royer Labs is one of the best-known manufacturers of ribbon mics. They’ve pioneered innovations in ribbon mic technology that allow them to be used on very loud sound sources without damage to the microphone. The R-121 is one of the most popular mics in existence and exhibits all the classic characteristics of a ribbon mic.
What about tube microphones?
Tube mics are a subset of condenser mics. Up until the 1960s, condensers used a tube for the amplification of the low-level diaphragm signal. Tubes sound nice, but have a lot of issues: heat, high power requirements, and they can suffer from microphonics. In the ’60s, a solid-state replacement for the tube was created: the FET, or field effect transistor. The FET emulates tube characteristics and has two benefits: smaller size and reduced power requirements. The first solid-state condenser mic designs used the same circuit except for the FET substitution, but they sounded different, crisper. They had lost the tube character.
Tube mics are revered for their warmth, wide frequency response, and pleasing sound. They are most commonly used for vocals, but I’ve used them for every instrument. There’s a robust market for inexpensive tube mic modification. Sometimes it’s as easy as swapping a tube, while others do capsule and component level changes. These mods can greatly enhance the sound of an inexpensive tube mic. A good mic closet should have at least one curated tube mic. They start at about $499 and can range upwards of $30,000.
Some manufacturers with tube mics in the below-$1,000 price range include Avantone, Warm Audio, Golden Age, and Lauten Audio. My recommendation is to audition several and find the one that will have the broadest application for your recording situation. They won’t sound exactly like their pricier counterparts, but they’ll give you a flavor in your mic closet that’s only possible with a tube microphone.
Tube mics to consider:
- Mojave MA-300SN ($1,399): Mojave was created by David Royer of Royer Labs. They use quality components for mics that meet exacting standards. The 300SN is a tube large-diaphragm condenser mic. It features a continuously variable pattern select, which ranges from omni to figure eight. The MA300SN has a warm low end with an open top.
- Miktek CV4 ($1,699 street): Miktek’s line of hand-built mics includes this large diaphragm condenser with nine polar patterns. I’ve used these on vocals and stringed instruments with great success.
- Peluso 22 47 SE ($2,149 street): Peluso Microphone Lab is a boutique company that hand builds each mic. The 22 47 is a reproduction of the venerable Neumann U 47. The 22 47 is a great choice for vocals and acoustic instruments, and I find myself using less EQ when recording with this mic. Their interpretations of other classic mics are also available.
Photo by Nick Sonsini
- Telefunken ELA M 251 (repro: $10,996/vintage: $25,000-plus street): Around 3,700 units of the original 251 were manufactured from 1960 to ’65, but a modern reproduction is available. It has an open top end without harshness, a smooth, rich midrange, and low-end warmth with punchiness. It’s an excellent vocal mic and excels on harmonically rich instruments.
Now, Go Forth and Record
You’ve got to start somewhere when building your mic closet. If you’re not tracking full bands, I’d recommend starting with a couple dynamics (like the SM57) and a set of LDCs. With these mics, you’ll be able to cover basic overdub sessions. From there, borrow mics from friends, explore the world of ribbon and tube mic sounds, and discover what works best for your home studio.
What About DIs?
Direct boxes, or DIs, are an integral part of any studio. They are used to connect (Hi-Z) instruments with low-impedance (Lo-Z) microphone preamps. Hi-Z devices, such as guitars and basses, have 1/4" outputs. The DI provides a 1/4" input to connect to your guitar and an XLR output which connects to a preamp. DIs also have a 1/4" output jack. This is used to pass the signal through the DI and connect to an amplifier. Often, a bass or guitar is recorded to two tracks—one signal from the DI and the other from an amplifier.
There are two types of DIs: passive and active. Passive devices have of an internal transformer that changes the impedance of the signal. Active DIs require a power source for their internal electronics and will have less signal degradation than a passive device. A good home studio should have at least one active DI and two passive DIs.
Modern DAW interfaces usually have built-in Hi-Z inputs via 1/4" jacks that allow you to connect directly to your interface. These negate the need for a DI.
Here are several DI boxes to consider:
- Radial StageBug S-B2 ($89 street): Radial is well known for their technology in direct box design. This is a passive DI with a small footprint.
- Radial Pro48 ($129 street): These active devices are full-range DIs with a bandwidth of 20 Hz to 20k.
- Rupert Neve Designs RNDI-1($299 street): Like most Neve designs, this active device is engineered for the highest fidelity audio and sounds great.
Digital Modeling Mics
Digital microphone modeling systems are a relatively new development. They combine a specially designed microphone with modeling software that allows you to record audio that sounds as if you had used a different microphone. The software models a variety of classic or vintage mics. The two frontrunners in this new tech are the Slate Digital VMS Virtual Microphone System and Universal Audio’s Sphere L22 Microphone Modeling System (which was developed in conjunction with Townsend Labs).
They use a sonically transparent microphone designed to interface with their modeling software. The signal is passed from the mic through a neutral mic pre (one that doesn’t color the sound too much) to your DAW input. The plugin is applied to the audio and an output mic model is selected. The result sounds as if it had been recorded with the selected mic.
Slate and UA accomplish this by testing and measuring a microphone’s behavior and mapping that behavior out in software. The software knows the characteristics of the recording mic and processes the audio, applying the differences to the signal. The recorded signal now sounds as if it was recorded with a $20,000 Neumann U 67 (or whichever mic you’ve selected).
The benefit of these systems is that it is non-destructive. Just like amp modeling plugins, there is a dry sound recorded in your DAW, and the processing is applied with a plugin. You have the ability to modify it throughout the recording process, finding the sound that works with your final production.
These systems offer a huge range of sounds and offer mic selections that would not be available in your average home studio. And each system offers a selection of recognized mic models with an established track record.
The lowdown:
• Slate Digital VMS Virtual Microphone System (mic and software $499 street): This system’s ML-2 is a small diaphragm mic. Once recorded, sound is processed via the VMS plugin (compatible with AAX, VST2, VST3, and AU formats). The VMS software includes 13 mic models, ranging from the AKG C12 to the Shure SM7B. Two add-on mic bundles are available for purchase from Slate: Blackbird Mics ($199 street), featuring five mics from Nashville’s Blackbird Studio, and Classic Tubes ($299 street), featuring five modeled mics.
• Universal Audio Sphere L22 Microphone Modeling System ($1,199 to $1,499 street): UA’s Sphere L22 was developed in conjunction with Townsend Labs. The Sphere software works the same as VMS, tuned for the provided mic and offering 34 output mic models.
The Sphere system uses a dual-capsule mic. This allows the software to take the signal from both capsules and create a 3D sonic picture of the modeled microphone. In theory, this should offer off-axis behavior similar to the originals. The mic can use both capsules to create a stereo recording, too.
The software is available in UAD, AAX, VST2, VST3, and AU formats. It offers more tweakable parameters than the VMS. So, if you’re a knob twister and like to fine-tune your sounds, the Sphere is a good choice. The additional controls come with a higher price tag.
- Tone Tips: Modelers vs. Traditional Rigs, Part 2 ›
- Amp Mic’ing vs. Impulse Responses ›
- The Recording Guitarist: Mic Makes Right ›
- Color Coding Sessions Can Save Your Butt - Premier Guitar ›
- How to Get More Out of Your Mics with Modelers - Premier Guitar ›
Sublime, fronted by Jakob Nowell, son of late Sublime singer Bradley Nowell, are in the studio writing and recording new songs for an upcoming full-length album. This marks their first new album since 1996.
When not performing at various festivals across North America in 2024, front man Jakob Nowell immersed himself in the Sublime catalog and found a deep sense of connection to his late father. The band is tapping into the 90s nostalgia, writing and recording the new songs with powerhouse producing duo Travis Barker and John Feldmann, in addition to working with producer Jon Joseph (BØRNS). The first single will be released this Summer via their newly established label Sublime Recordings.
"I grew up on Sublime. ‘40oz. to Freedom’ changed the way I listened to music. I’m so honored to be working with the guys in Sublime. Creating music for this album has been so fun and exciting. Bradley comes through his son Jakob while writing in the studio and performing. Chills every day in the studio when he sings and play guitar. This is going to be really special." – Travis Barker
“Sublime has always been a huge influence on me and to be able work with the band has been inspirational and game changing…It has been a highlight of my life to work on such a seminal record with such talented people. I’m so grateful for this opportunity and to continue the legacy and keep it authentic to what they have historically done.” – John Feldmann
After Jakob Nowell’s debut as Sublime’s new front man at Coachella 2024, he and his uncles Bud Gaugh and Eric Wilson continued the momentum of this latest chapter of the band, performing at over 20 festivals and shows across North America by the end of last year. Additional highlights from 2024 include Sublime’s late-night television debut on The Tonight Show Starring Jimmy Fallon, a 4-song set on the Howard Stern Show and the band’s first top 10 hit on alternative radio since 1997 with their single “Feel Like That,” featuring the vocals of both Bradley Nowell and his son Jakob together.
2025 is shaping up to be an even busier year for the band, with a handful of headlining shows, high-profile festival appearances to support the release of the new album.
For more information, please visit sublimelbc.com.
Sublime 2025 Tour Dates
- April 5 – LIV Golf Miami – Miami, FL
- April 18 – Red Rocks Amphitheater – Morrison, CO
- May 3 – Beachlife Festival – Redondo Beach, CA
- May 16 – Welcome To Rockville – Daytona Beach, FL
- May 23 – BottleRock Napa Valley – Napa, CA
- May 25 – Boston Calling – Boston, MA
- June 14 – Vans Warped Tour – Washington, DC
- July 12 – 89.7 The River’s 30th Anniversary Show – Omaha, NE
- July 20 – Minnesota Yacht Club Festival – Saint Paul, MN
- September 14 – Sea.Hear.Now – Asbury Park, NJ
- September 19 – Shaky Knees Festival – Atlanta, GA
Price unveiled her new band and her new signature model at a recent performance at the Gibson Garage in Nashville.
The Grammy-nominated alt-country and Americana singer, songwriter, and bandleader tells the story behind the creation of her new guitar and talks about the role acoustic Gibson workhorses have played in her musical history—and why she loves red-tailed hawks.
The Gibson J-45 is a classic 6-string workhorse and a favorite accomplice of singer-songwriters from Bob Dylan to Jorma Kaukonen to James Taylor to Gillian Welch to Lucinda Williams to Bruce Springsteen to Noel Gallagher. Last week, alt-country and Americana artist Margo Price permanently emblazoned her name on that roster with the unveiling of her signature-model J-45. With an alluring heritage cherry sunburst finish and a red-tail-hawk-motif double pickguard, the instrument might look more like a show pony, but under the hard-touring and hard-playing Price’s hands, it is 100-percent working animal.
The 6-string was inspired by the J-45 she bought at Nashville’s Carter Vintage Guitars after she was signed to Third Man Records, where she made her 2016 ice-breaker album, Midwest Farmer’s Daughter. But her affection for Gibson acoustics predates that, going back to when she found a 1956 LG-3 in her grandmother’s home. The guitar had been abandoned there by her songwriter great uncle, Bobby Fischer.
“I played it for years before I found my J-45,” Price recounts. “At Carter Vintage, I tried a lot of guitars, but when I picked up that J-45, I loved that it was a smaller guitar but really cut through, and I was just really drawn to the sound of it. And so I went home with that guitar and I’ve been playing it ever since.”
“Having a signature model was something I had dreamed about.”
Of course, Price was also aware of the model’s history, but her demands for a guitar were rooted in the present—the requirements of the studio and road. The 1965 J-45 she acquired at Carter Vintage, which is also a cherry ’burst, was especially appealing “compared to a Martin D-21 or some of the other things that I was picking up. I have pretty small hands, and it just was so playable all up the neck. It was something that I could easily play barre chords on. I could immediately get everything that I needed out of it.”
If you’ve seen Price on TV, including stops at Saturday Night Live, The Late Show With Stephen Colbert, and Jimmy Kimmel Live!, you’ve seen her ’65. And you’ve also seen, over the years, that part of the soundhole’s top has been scraped away by her aggressive strumming. It’s experienced worse wear from an airline, though. After one unfortunate flight, Price found her guitar practically in splinters inside a badly crushed case. “It was like somebody would have had to drive over this case with a truck,” she relates. Luckily, Dave Johnson from Nashville’s Scale Model Guitars was able to put Humpty Dumpty back together again.
After that, an alternative guitar for the road seemed like a requirement. “Having a signature model was something I had dreamed about,” Price says. Friends in her songwriting circle, including Lukas Nelson and Nathaniel Rateliff, already had them. Four years ago, a tweet asking which women they thought should have signature models appeared, and one of her fans wrote “Margo Price.” Smartly, Price tagged Gibson and retweeted. Codey Allen in Gibson entertainment relations spotted the tweet and agreed.
The double pickguard was chosen for Price’s J-45 because of its symmetry, as a nod to the Hummingbird, and due to her heavy strumming hand.
Photo courtesy of Gibson
“The neck is not quite as small as my J-45, but it is just a bit smaller than many J-45s fives, and very playable no matter what size hands you have.”
“And so we began our journey of building this guitar,” Price says. “I debated whether it should be the LG-3, which I still have hanging on my wall, or the J-45. I went to Montana and visited their [acoustic] factory and sat down with Robi Johns [senior product development manager at Gibson acoustic], and we ultimately decided that the J-45 was my guitar. Then we started talking about the specs. We did pull from the LG-3 in that the body of this signature guitar is a bit smaller. It still has a really loud, clear sound that rings through. The neck is not quite as small as my 1965 J-45, but it is just a bit smaller than many J-45s, and very playable no matter what size hands that you have.”
The pickup that Price selected is a L.R. Baggs VTC Element with a preamp, and she took a prototype of the guitar on the road opening for the Tedeschi Trucks Band. “I am used to playing with a really loud band, with drums and sometimes a couple electric guitars, and I wanted to make sure that this guitar just cut through,” she says. “It was really important to me that it be loud, and it cut beautifully. It’s got a mahogany body and scalloped bracing, which makes it very sturdy. This guitar is a workhorse, just like me.”
The Margo Price J-45’s most arresting characteristic, in addition to its warm sunburst finish, is its double-sided pickguard with an etching of a quartet of red-tailed hawks in flight. It’s practical for her strumming style, but it’s also got a deeper significance.
“We talked about all sorts of things that we could put on the pickguard, and I’ve always been a big fan of the Hummingbird, so what we did is a bit of a nod to that,” Price continues. “I’ve always been drawn to red-tailed hawks. They are supposed to be divine messengers, and they have such strength. They symbolize vision and protection. I would always count them along the highway as I’d be driving home to see my family in Illinois.”
Birds of a feather: “I’ve always been drawn to red-tailed hawks,” says Price. “They are supposed to be divine messengers, and they have such strength. They symbolize vision and protection.”
Photo courtesy of Gibson
With its comfortable neck, slightly thinner body, and serious projection, Price notes, “I wanted my guitar to be something that young girls can pick up and feel comfortable in their hands and inspire songs, but I didn’t want it to be so small that it felt like a toy, and that it didn’t have the volume. This guitar has all of those things.” To get her heavy sound, Price uses D’Addario Phosphor Bronze (.012–.053) strings.
Price says she and her signature J-45, which is street priced at $3,999, have been in the studio a lot lately, “and I have a whole bunch of things I’m excited about.” In mid March, she debuted her new band—which includes Logan Ledger and Sean Thompson on guitars, bassist Alec Newman, Libby Weitnauer on fiddle, and Chris Gelb on drums—in a coming out party for the Margo Price Signature Gibson J-45 at the Gibson Garage in Nashville. “I’ve been with my previous band, the Price Tags, for more than 10 years, and it’s definitely emotional when a band reaches the end of its life cycle,” she says. “But it’s also really exciting, because now, having a fiddle in the band and incredible harmony singers … it’s a completely different vibe. I’ve got a whole bunch of festivals coming up this year. We’re playing Jazz Fest in New Orleans, and I’m so excited for everyone to hear this new iteration of what we’re doing.”
With its heritage cherry sunburst finish and other appointments, the Margo Price Signature Gibson J-45 balances classic and modern guitar design.
Photo courtesy of Gibson
Get premium spring reverb tones in a compact and practical format with the Carl Martin HeadRoom Mini. Featuring two independent reverb channels, mono and stereo I/O, and durable metal construction, this pedal is perfect for musicians on the go.
The Carl Martin HeadRoom Mini is a digital emulation of the beloved HeadRoom spring reverb pedal, offering the same warm, natural tone—plus a little extra—in a more compact and practical format. It delivers everything from subtle room ambiance to deep, cathedral-like reverberation, making it a versatile addition to any setup.
With two independent reverb channels, each featuring dedicated tone and level controls, you can easily switch between two different reverb settings - for example, rhythm and lead. The two footswitches allow seamless toggling between channels or full bypass.
Unlike the original HeadRoom, the Mini also includes both mono and stereo inputs and outputs, providing greater flexibility for stereo rigs. Built to withstand the rigors of live performance, it features a durable metal enclosure, buffered bypass for signal integrity, and a remote jack for external channel switching.
Key features
- Two independent reverb channels with individual tone and level controls
- Mono and stereo I/O for versatile routing options
- Buffered bypass ensures a strong, clear signal
- Rugged metal construction for durability
- Remote jack for external channel switching
- Compact and pedalboard-friendly design
HeadRoom Mini brings premium spring reverb tones in a flexible and space-savingformat—perfect for any musician looking for high-quality, studio-grade reverb on the go.
You can purchase HeadRoom Mini for $279 directly from carlmartin.com and, of course, also from leading music retailers worldwide.
For more information, please visit carlmartin.com.
Handwired in Hollywood with NOS components, these pedals deliver classic tones reminiscent of iconic rock albums. Get authentic vintage tone with modern reliability.
Rock N’ Roll Relics, known for crafting beautifully aged guitars, is stepping into the world of guitar effects with two new stompboxes: The StingerBoost and The Stinger Drive. True to the brand’s vintage aesthetic and rock ‘n’ roll spirit, these pedals are handwired in Hollywood and built to look, feel, and sound like they’ve been gigged for decades.
The Stinger Boost: This single-transistor boost features a Dallas Rangemaster-style circuit, with a NOS (New Old Stock) Fairchild Silicon transistor and a NOS Sanyo Germanium transistor. The circuit is modified beyond a typical Rangemaster to provide wider bandwidth for more of a full-range, mid-focused boost. The rest of its small components are all high-quality NOS, sourced from 1970s stockpiles. It’s completely hardwired and uses vintage-style clothwire, including a true bypass footswitch switch.
The Stinger Boost delivers classic midrange honk that cuts through any mix. Its switchable silicon and germanium circuit lets you dial in everything from glassy bite to warm, vintages aturation. The germanium mode provides a smooth and warm boost, and the silicon circuit delivers a brighter, hard-edged push. The pedal’s single Boost knob offers everything from a subtle push to a full-on vintage-style gain boost. Think back to the classic lead tones of theBeano album, the melodies of Queen, and the blues shredding of Rory Gallagher: that’s what you’re getting with the Stinger Boost – capable of over 30dB of gain with a midrange bump.
The Stinger Drive: Inspired by the iconic MXR Distortion+ and DOD250 pedals, the StingerDrive features Volume and Gain controls to dial in rich, midrange-forward drive with a smoother high end than traditional circuits. Built using a mix of NOS and modern components, this pedal delivers sought-after vintage tone with modern reliability.
The Stinger Drive features an LM741 asymmetrical hard clipping circuit utilizing a germanium diode and silicon transistor, pushing forward loads of even-order harmonic distortion. It provides more volume than a vintage overdrive and also more gain which, at its maximum, stands on the knife’s edge of oscillation for really hairy tones.
Combining old-school looks with modern reliability, each Rock N’ Roll Relics pedal is hand-agedand uniquely relic’d, making it look like it has spent 30 years on the road. Open one up, andyou’ll see true vintage-style wiring, with all components on full display—just like they did back inthe day.
- NOS transistors & hand-selected components for authentic vintage tone
- 9-volt operation via external power supply or on board battery
- Individually hand-aged enclosures for a one-of-a-kind look
- True bypass switching
The Rock N’ Roll Relics Stinger Boost carries a $279 street price and the Stinger Drive carries a $289 street price. They’re available from Rock N’ Roll Relics dealers and direct from RockNRollRelics.net.
For more information, please visit rocknrollrelics.com.