
Welcome to the tube zoo, where you’ll get to know about the nature and habits of output and preamp tubes. And how they perform in the wilds of amplification—and in your own amp.
Of all the tonally tweakable elements in the extensive chain of components that define your sound as a guitarist, the tubes tucked into your amplifier might be the most enigmatic. Working symbiotically with the circuits and transformers housed alongside them, these tubes help to determine the way your playing is translated, from the signal produced at the guitar’s pickups to the sound waves ultimately pumped into the air by the speaker and broadcast to listeners’ ears. Given their role in the signal chain, tubes can greatly influence the feel of your playing, as well as the sound.
Alternative guitar amp options have threatened to bury tubes for six decades—since the arrival of solid-state amps in the 1960s to the proliferation for modeling amps in recent years. Yet the rumors of the tube amp’s death have been greatly exaggerated, and they continue to be used by more pro and hobby players around the world than any other type of amplifier. Even the sounds of modeling rigs are based on the tone and playing feel of myriad classic tube circuits.
Didacts will occasionally argue that tubes themselves don’t have a sound. Certainly, that’s true as far as the silence you’ll hear if you unplug a tube and hold it up to your ear. So, sure, the design and circuit of the amp in which any tube is used sets the foundation of its overall tone. But tubes do very much enhance or define certain sonic characteristics of amps, which is something you discover pretty quickly when you swap one tube type for another (in amps that allow this)—only to discover a distinct shift in your amp’s tonal personality.
“A survey of many classic and boutique amps usually reveals specific tube types enhancing distinct sonic characteristics time and again.”
It’s probably best, therefore, to think of many classic amps and traditional tube types as working hand-in-hand to present familiar sonic templates. For that reason, throughout this guide we’ll nod to a handful of familiar amplifier makes and models when referencing many tubes—and output tubes in particular, since the most common preamp tubes are often interchangeable between drastically different amp designs.
Also, while it might be true that a good amp designer can coax nearly any tone out of any conventional type of output tube, a survey of many classic and boutique amps usually reveals specific tube types enhancing distinct sonic characteristics time and again. For example, Dick Denney might have built the most famous iterations of the Vox AC15 and AC30 around EL84s, because they were plentiful and affordable, but now that those sounds have been blueprinted, we know which tubes to turn to for consistently achieving them.
Let’s start our guide with a look at the main output tube types used in guitar amps, then we’ll move on to common preamp tubes. Per-tube prices quoted are for current or recently manufactured examples made in Russia, Eastern Europe, and China, as surveyed at reputable dealers such as Mojotone, Antique Electronic Supply, Sweetwater, Telefunken, the Tube Doctor, EHX, and the Tube Store. Tags for special or limited versions of tubes are typically a little higher.
Output Tubes
Output tubes (also called power tubes) are the larger of the tube types within your amp and are usually found toward the opposite end of the chassis from the amp’s input. These tubes receive the guitar signal that the preamp tubes have already amplified slightly and amplify it much more, into a signal that can be pumped through a speaker via an output transformer. Let’s take a family-by-family look at these tubes
6L6 Types
Tone Template: Big American
Price: $25 to $50 street
Courtesy of The Tube Doctor
Used in pairs for 35 to 50 watts or quads for 80 to 100 watts, 6L6s are the classic big American tube, probably best defined by the sound of the larger, legendary Fender amps of the ’50s and ’60s: the tweed Bassman, the black-panel Twin Reverb, the Super Reverb, and more. This tube has a bold, solid voice with firm lows and prominent highs. The sound can almost be strident in loud, clean amps that were designed for maximum headroom, or silkier and more rounded in smaller amps—like many of the tweed era—that allow for easier and earlier clipping.
Different 6L6s offer varying types of tonal performance. The 6L6GB and 6L6GC, for example, are a little softer/rounder and firmer/bolder, respectively, while the latter is also capable of handling higher voltages and delivers later breakup with increased headroom. (Note: These aren’t better/best distinctions. Either tube may be preferable according to your sonic needs, or might be required by your amp’s specifications.) A “W” designation on either of these denotes a more rugged tube originally intended for military use.
“6L6s are the classic big American tube, probably best defined by the sound of the larger, legendary Fender amps of the ’50s and ’60s.”
The original 5881 tubes manufactured in the U.S. in the ’50s and ’60s are a tougher sibling of the 6L6. They put out a little less power and break up a little earlier than the 6L6GC. Currently manufactured 5881s, however, are usually 6L6 types that have been relabeled, and therefore don’t vary greatly in their characteristics. If you’re lucky, you might find some new old stock (NOS) originals (see sidebar at bottom of page).
In many amps, all of the tubes mentioned in this 6L6 section can be swapped for each other, with some caveats. Always refer to your amp manufacturer’s instructions before doing so, and be aware that higher-powered amps designed with 6L6GCs in mind might run at voltages too high for 6L6GBs or 5881s.
For a further sonic reference point, 6L6 types also appear in many vintage Gibson, Silvertone, Danelectro, and Valco amps, plus early Marshall JTM45s, many Mesa/Boogie Mark Series models, Dumbles, many powerful Soldano and Bogner amps, and boutique favorites like the Carr Rambler and Dr. Z Z-28 MkII.
EL34s
Tone Template: British Stack
Price: $23 to $50 street
Photo courtesy of Telefunken
EL34s, used in pairs for 45 to 60 watts or quads for 100 to 120 watts, are responsible for the archetypal 50- and 100-watt tone from across the Atlantic, as delivered by the classic Marshall plexi variations. It is characteristically thick and mid-forward, with round lows, crispy highs, and a slightly granular texture overall—and smoothly compressed and aggressive when driven hard. The EL34 can also deliver tighter and bone-crunchingly punchy sounds to arena-rock stages in amps that can be pushed up to 120 watts with sets of four tubes, such as the Hiwatt DR103. That’s thanks to this tube’s ability to handle very high plate voltages.
The EL34 is featured in post-1967 Marshalls like the JMP50 and JMP100 plexi and metal-panel amps, later Master Model 2203s and 2204s, JCM800s, and the majority of modern models. These tubes are also used by (as mentioned) Hiwatt, Orange, and Sound City, and in Vox’s AC50 and AC100, as well as several amps from Selmer and Traynor. Contemporary makers seeking that Brit-stack kerrang! at full volume usually turn to EL34s, so they are also part of the formulation of high-gain-design builds from Rivera, Bogner, Friedman, and Mesa/Boogie, as well as the Matchless Clubman, TopHat Emplexador, and Komet K60.
KT66s
Tone Template: Bold British
Price: $45 to $70 street
Courtesy of The Tube Doctor
This large, imposing Coke-bottle of a tube was Britain’s response to the American 6L6. As such, it has broadly similar characteristics and produces roughly the same wattage in pairs and quads, although it can handle higher voltages and adds its own sonic personality to the brew. Given this, the KT66 can be used in place of 6L6GCs in many amps, although you should check your manufacturer’s guidelines just to be safe.
The KT66 is probably best known, in vintage amps, for its use in many Marshall JTM45s of the early ’60s, which started with 6L6s and 5881s (following their inspiration of Fender’s tweed Bassman circuit) before moving to the British-made tube when the American “valves,” as the Brits call tubes, became scarce in the U.K. In recent decades, the KT66 has been rediscovered by many boutique amp makers. It’s the tube of choice for the Dr. Z Route 66 and the original single-ended Carr Mercury, among others. Along with its good balance and clarity throughout the frequency range, the KT66 generally offers a slightly bolder low end than the 6L6, and what some players hear as a sweeter, juicier midrange response—making it something of a good blend of the 6L6GC and the EL34.
6550s and KT88s
Tone Template: Punchy, Powerful, and Surprisingly Versatile
Price: $50 to $80 street
Courtesy of Telefunken
A big, powerful tube capable of producing massive wattage in the right circuit, the 6550 has also been used somewhat against type by a surprising number of creative boutique amp makers. In the late ’60s and ’70s, the 6550 was more likely to be found in bass amps—six of them created the original Ampeg SVT’s stadium-rumbling tones—but was also used, for a time, in Marshall guitar amps exported to the U.S. because its ruggedness and greater availability eased servicing issues.
Sonically, the 6550 is bold, clear, tight, and well-composed, with very little compression when pushed, but an aggressive, muscular crunch when it does begin to break up. Some makers—George Alessandro, for one—have cleverly used it to achieve more nuanced tones, but usually it’s a tube that’s employed when massive wattage is the ultimate goal.
Courtesy of The Tube Doctor
Although not identical to the 6550, the KT88 is a common substitute that presents many of the same characteristics. Sonically, it leans somewhere between the 6550 and EL34, but with the tighter low end and massive output of the former. It can usually be swapped directly for a 6550, and often for an EL34, with some slight modifications (as ever, consult your manufacturer or a good amp tech). The mighty 200-watt Marshall Major is the best vintage reference point for this output tube, but it has also been used more recently in the RedPlate BluesMachine and Fryette Sig:X, among others—generally amps seeking either high headroom or a greater proportion of preamp-tube overdrive to output-tube distortion.
“If you’re curious about the sonic effects of variations in 12AX7s that can be used in your amp, it’s worth trying a few to check out the phenomenon for yourself.”
6V6GTs
Tone Template: Juicy, Smaller American
Price: $22 to $55 per tube
Courtesy of Telefunken
Originally an American-made tube (though later produced elsewhere), the 6V6 is often thought of as the little brother of the 6L6. But, despite its use in the smaller- to medium-sized amps made by golden-age American companies of the ’50s and ’60s—who used 6L6s in their larger amps, it really has a sonic signature all its own. A pair will generate around 15 to 18 watts in a cathode-biased amp (think tweed Deluxe) or upwards of 22 watts in a fixed-bias circuit (Deluxe Reverb), and they were also sometimes used in quads to produce 30 to 50 watts. Their sonic personality? Round, rich cleans and a juicy, relatively mid-forward sound when pushed into distortion, with notable compression and a hint of granularity at the core.
In addition to the notable Fender models the 6V6 appeared in, these tubes were also deployed in the most popular Gibson amps of the ’50s and have been used in near-countless reissue and boutique models over the past couple of decades. The Tone King Imperial, Bogner Goldfinger 45, Carr Mercury V and Skylark, Divided By 13 CJ 11, and Victoria Silver Sonic all used 6V6s in their output stages.
EL84
Tone Template: British Chime
Price: $17 to $38 per tube
Courtesy of Electro-Harmonix
In something of a parallel to the American 6V6, the EL84 (originally a British and European tube) is often talked of as a “junior EL34,” although, again, it has a personality very much its own. This tube is notable for being the only 9-pin (noval) tube in our selection (most tubes are octal, having 8 pins), and it can look much like a taller preamp tube. The EL84 delivers around 15 to 18 watts in pairs, or from 30 to 36 watts in quads.
Far and away most famous for its use in the Vox AC15 and AC30, the EL84 is known for its sweet, bright, chimey clean tones and succulent, textured, harmonically saturated overdrive. “Shimmer” and “bloom” are among the adjectives players use to describe EL84s in the sweet spot, just at the edge of breakup. In addition to the archetypal original Vox amps and later reissues, the EL84 has been popular with a long list of other companies, including boutique builders who clearly take their inspiration from the British classics.
Popular amps like the Matchless Lightning, Spitfire and DC-30; Dr. Z Carmen Ghia and Maz (the latter has two equivalent 6N14Ns power tubes); 65amps London and Soho; TopHat Club Royale; Friedman JJ Junior; Mesa/Boogie Mark Five: 25 and 35; and Fender Blues Junior and Pro Junior all use this tube.
Preamp Tubes
Generally speaking, preamp tubes are less likely to define the foundational sound of any given amplifier, although swapping one for another—even of the same type, but a variation or a tube from a different maker—can still impose a noticeable change on your tone. One reason we think of preamp tubes as less of a defining element in most guitar amps is because the vast majority of amps use the same preamp tube types. The 12AX7 is far and away the most common preamp tube and has been since the early ’50s. Again, variations on makes of 12AX7s can still stamp elements of their own personality on the sound of any amp, and swapping one manufacturer’s 12AX7 for another might produce dramatic sonic changes, but not the same sort of tectonic shift in the basic characteristics of any given amp as output tubes.
If you’re curious about the sonic effects of variations in 12AX7s that can be used in your amp, it’s worth trying a few to check out the phenomenon for yourself, in order to select a favorite. Otherwise, it’s probably more informative to discuss their different levels of gain available via various preamp tubes. That will alter the sound and feel of most amps, since the proportions of clean and overdriven sound, the point on the volume control at which distortion sets in, and other gain-related factors all play a big part in shaping what we think of as our tone.
Each major type of preamp tube exhibits what we call a “gain factor,” and the relative comparison of this spec gives us some indication of how hard that tube will drive the preamp stage of any amp. To that end, despite the 12AX7’s domination of the market, let’s also look at a few other tubes, too. (Note: We’re only discussing common 9-pin (noval) preamp tubes here, but the lesser-used, octal-based preamp tubes, more common up until the early to mid-’50s, are still enjoyed by some players.)
Dual-Triode Preamp Tubes
12AX7s (aka ECC83s), 5751s, 12AT7s, 12AY7s
Price: $18 to $35
Each of these tube types contains two triode gain stages within one bottle—hence, the “dual-triode” name—and they can perform their duties in two parts of the preamp circuit simultaneously using each triode. [Each triode gain stage consists of three electrodes: a cathode filament, anode plate, and control grid. For more background, check out Dan Formosa’s article “Tube-Amp Basics for Beginners,” in the June 2021 issue, or at premierguitar.com.] In theory, any one of these tubes—listed above in descending gain levels—can be substituted for each other with little chance of damage to your amplifier. Technically, the 12AT7 is usually biased differently than the others, so might not perform optimally in a circuit set up for a 12AX7, but you’re unlikely to damage your amp by trying it out. (If you’re curious, swap it in for a short period of time, and if you like the results, check with your amp’s manufacturer or a good tech before using it full-time.)
By the way, here are the specific gain factor ratings—the measures for how much a tube amplifies the input signal—for these tubes:
12AX7: 100
Courtesy of the Tube Doctor
5751: 70
Courtesy of Electro-Harmonix
12AT7: 60
Courtesy of Electro-Harmonix
12AY7: 40
Courtesy of The Tube Doctor
The main effect of swapping between these tubes of descending gain factors will be increased headroom and a later onset of distortion as you run down through the ranks. Each comes with its own nuanced sonic characteristics, too, which are difficult to define when divorced from the specific circuit in which they are used. Note, however, that many players find the 12AT7 (most commonly seen in reverb and phase-inverter positions) to be a little dull or cold-sounding, even as compared to the lower-gain 12AY7.
The 12AY7 is notable for its use in the first gain stage of most tweed Fender amps of around 1952 to ’60. Over the years, many players have swapped these for more common 12AX7s, which delivers earlier breakup and is desirable for some playing styles. This hotter tube can lead to a somewhat “fizzier” distortion when pushed hard in this type of circuit, though, and the 12AY7 is still considered to deliver the proper tone of classics like the 5E3 Deluxe, 5F4 Super, and 5F6-A Bassman.
Pentode Preamp Tubes
EF86, 5879
Price: $35 to $200
Courtesy of The Tube Doctor
Seen far less often but still beloved by some players, the pentode preamp tube houses a single pentode gain stage within a glass envelope that’s otherwise identical to the 12AX7 and the others above. As you might guess, pentode tubes have five electrodes, with screen and suppressor grids added to the 12AX7 family’s three. These are not, however, interchangeable for dual-triode tubes, so don’t even try it!
The most common pentode preamp tube is the EF86 (aka 6267), found in the classic iteration of the early ’60s Vox AC15. This tube reputedly has an even higher gain factor than the 12AX7—although the exact number is debated—and is characterized by a fat, rich sound. It’s prone to less self-distortion than the dual-triodes, too, meaning it passes a full-frequency signal along to the next stage in the amp without adding much of its own fizz or sizzle, although it can certainly contribute to tube overdrive. It also resists collapsing into mush when hit by an overdrive pedal in front of the amp. Boutique amps that employ the EF86 include the Matchless DC-30 (in channel 2, for high gain), the Dr. Z Z-28, and the Matchless DC-30.
Another pentode tube is the American-made 5879, which has similar characteristics to the EF86, although it also has different internal pin connections and therefore cannot be used in place of it. Probably best known for its use in the Gibson GA-40 Les Paul amp of the late ’50s, this one has most notably been employed in several current models from Divided By 13.
The Skinny
Okay, now you know all the basics about tubes. Use it as you will—to experiment, to hold your own in debates with fellow gear nerds, or as another stepping stone on your path to becoming a tone sensei.
Follow Your NOS
Courtesy of the Tube Store
Courtesy of the Tube Store
Courtesy of the Tube Store
As you get deeper into the world of replacement tubes for guitar amplifiers, and particularly if you fuel your knowledge by perusing online forums, you’re likely to come across the term “NOS” again and again, along with the recommendation that those are the tubes you need to buy. Short for “new old stock,” NOS tubes are those that were manufactured many years ago—usually during the golden age of American and European tube production—but have never been used. They are old stock, but are essentially new because they have never been installed in an amplifier.
The demise of the vacuum tube industry in the U.S. and Europe began in the late 1960s and early ’70s, when transistors took the reins for just about all amplification duties other than those of guitar amps. Production dwindled through the ’70s and all but disappeared after, although a few tubes were made in the U.S. (the 6550, in particular) in relatively small numbers right up until 1993. More to our point, though, since the early ’80s all new tubes have been manufactured in Eastern Europe and China, particularly because these regions still needed them for use in military equipment that was slower to update to new tech. It’s worth remembering that once the technology in military and consumer electronics moved forward, the guitar-amp and audiophile markets weren’t enough to sustain the tube industry.
Guitarists have been plundering whatever stocks of NOS tubes they could find for a good three decades or more. So, there aren’t a whole lot of genuine NOS tubes left, and those that remain are very expensive. Beyond this, the bigger issue with acquiring NOS tubes today revolves around quality and verification: a lot of sub-par tubes that were rejected during testing over the years have ended up being recycled as NOS, as have a lot of used tubes pulled from old amps and polished up. Buying NOS from a reputable dealer can help mitigate these issues, but, once again, you will pay a premium. For example, we recently spotted an Amperex Bugle Boy 12AX7 for sale at $349.95. Is it that much better than a JJ Electronic 12AX7 for 20 bucks?
No matter how much chat-room pundits rave that you must use NOS tubes, current (or at least recent) tubes provide good tone and excellent reliability in the vast majority of guitar amps in use today. It’s also worth considering the fact that contemporary amp makers are usually designing and fine-tuning their circuits with current-manufacture tubes in mind, so while a rare and expensive NOS substitute might get a little more out of them, that is by no means guaranteed.
This legendary vintage rack unit will inspire you to think about effects with a new perspective.
When guitarists think of effects, we usually jump straight to stompboxes—they’re part of the culture! And besides, footswitches have real benefits when your hands are otherwise occupied. But real-time toggling isn’t always important. In the recording studio, where we’re often crafting sounds for each section of a song individually, there’s little reason to avoid rack gear and its possibilities. Enter the iconic Eventide H3000 (and its massive creative potential).
When it debuted in 1987, the H3000 was marketed as an “intelligent pitch-changer” that could generate stereo harmonies in a user-specified key. This was heady stuff in the ’80s! But while diatonic harmonizing grabbed the headlines, subtler uses of this pitch-shifter cemented its legacy. Patch 231 MICROPITCHSHIFT, for example, is a big reason the H3000 persists in racks everywhere. It’s essentially a pair of very short, single-repeat delays: The left side is pitched slightly up while the right side is pitched slightly down (default is ±9 cents). The resulting tripling/thickening effect has long been a mix-engineer staple for pop vocals, and it’s also my first call when I want a stereo chorus for guitar.
The second-gen H3000S, introduced the following year, cemented the device’s guitar bona fides. Early-adopter Steve Vai was such a proponent of the first edition that Eventide asked him to contribute 48 signature sounds for the new model (patches 700-747). Still-later revisions like the H3000B and H3000D/SE added even more functionality, but these days it’s not too important which model you have. Comprehensive EPROM chips containing every patch from all generations of H3000 (plus the later H3500) are readily available for a modest cost, and are a fairly straightforward install.
In addition to pitch-shifting, there are excellent modulation effects and reverbs (like patch 211 CANYON), plus presets inspired by other classic Eventide boxes, like the patch 513 INSTANT PHASER. A comprehensive accounting of the H3000’s capabilities would be tedious, but suffice to say that even the stock presets get deliciously far afield. There are pitch-shifting reverbs that sound like fever-dream ancestors of Strymon’s “shimmer” effect. There are backwards-guitar simulators, multiple extraterrestrial voices, peculiar foreshadows of the EarthQuaker Devices Arpanoid and Rainbow Machine (check out patch 208 BIZARRMONIZER), and even button-triggered Foley effects that require no input signal (including a siren, helicopter, tank, submarine, ocean waves, thunder, and wind). If you’re ever without your deck of Oblique Strategies cards, the H3000’s singular knob makes a pretty good substitute. (Spin the big wheel and find out what you’ve won!)
“If you’re ever without your deck of Oblique Strategies cards, the H3000’s singular knob makes a pretty good substitute.”
But there’s another, more pedestrian reason I tend to reach for the H3000 and its rackmount relatives in the studio: I like to do certain types of processing after the mic. It’s easy to overlook, but guitar speakers are signal processors in their own right. They roll off high and low end, they distort when pushed, and the cabinets in which they’re mounted introduce resonances. While this type of de facto processing often flatters the guitar itself, it isn’t always advantageous for effects.
Effects loops allow time-based effects to be placed after preamp distortion, but I like to go one further. By miking the amp first and then sending signal to effects in parallel, I can get full bandwidth from the airy reverbs and radical pitched-up effects the H3000 can offer—and I can get it in stereo, printed to its own track, allowing the wet/dry balance to be revisited later, if needed. If a sound needs to be reproduced live, that’s a problem for later. (Something evocative enough can usually be extracted from a pedal-form descendant like the Eventide H90.)
Like most vintage gear, the H3000 has some endearing quirks. Even as it knowingly preserves glitches from earlier Eventide harmonizers (patch 217 DUAL H910s), it betrays its age with a few idiosyncrasies of its own. Extreme pitch-shifting exhibits a lot of aliasing (think: bit-crusher sounds), and the analog Murata filter modules impart a hint of warmth that many plug-in versions don’t quite capture. (They also have a habit of leaking black goo all over the motherboard!) It’s all part of the charm of the unit, beloved by its adherents. (Well, maybe not the leaking goo!)
In 2025, many guitarists won’t be eager to care for what is essentially an expensive, cranky, decades-old computer. Even the excitement of occasional tantalum capacitor explosions is unlikely to win them over! Fortunately, some great software emulations exist—Eventide’s own plugin even models the behavior of the Murata filters. But hardware offers the full hands-on experience, so next time you spot an old H3000 in a rack somewhere—and you’ve got the time—fire it up, wait for the distinctive “click” of its relays, spin the knob, and start digging.
The luthier’s stash.
There is more to a guitar than just the details.
A guitar is not simply a collection of wood, wire, and metal—it is an act of faith. Faith that a slab of lumber can be coaxed to sing, and that magnets and copper wire can capture something as expansive as human emotion. While it’s comforting to think that tone can be calculated like a tax return, the truth is far messier. A guitar is a living argument between its components—an uneasy alliance of materials and craftsmanship. When it works, it’s glorious.
The Uncooperative Nature of Wood
For me it all starts with the wood. Not just the species, but the piece. Despite what spec sheets and tonewood debates would have you believe, no two boards are the same. One piece of ash might have a bright, airy ring, while another from the same tree might sound like it spent a hard winter in a muddy ditch.
Builders know this, which is why you’ll occasionally catch one tapping on a rough blank, head cocked like a bird listening. They’re not crazy. They’re hunting for a lively, responsive quality that makes the wood feel awake in your hands. But wood is less than half the battle. So many guitarists make the mistake of buying the lumber instead of the luthier.
Pickups: Magnetic Hopes and Dreams
The engine of the guitar, pickups are the part that allegedly defines the electric guitar’s voice. Sure, swapping pickups will alter the tonality, to use a color metaphor, but they can only translate what’s already there, and there’s little percentage in trying to wake the dead. Yet, pickups do matter. A PAF-style might offer more harmonic complexity, or an overwound single-coil may bring some extra snarl, but here’s the thing: Two pickups made to the same specs can still sound different. The wire tension, the winding pattern, or even the temperature on the assembly line that day all add tiny variables that the spec sheet doesn’t mention. Don’t even get me started about the unrepeatability of “hand-scatter winding,” unless you’re a compulsive gambler.
“One piece of ash might have a bright, airy ring, while another from the same tree might sound like it spent a hard winter in a muddy ditch.”
Wires, Caps, and Wishful Thinking
Inside the control cavity, the pots and capacitors await, quietly shaping your tone whether you notice them or not. A potentiometer swap can make your volume taper feel like an on/off switch or smooth as an aged Tennessee whiskey. A capacitor change can make or break the tone control’s usefulness. It’s subtle, but noticeable. The kind of detail that sends people down the rabbit hole of swapping $3 capacitors for $50 “vintage-spec” caps, just to see if they can “feel” the mojo of the 1950s.
Hardware: The Unsung Saboteur
Bridges, nuts, tuners, and tailpieces are occasionally credited for their sonic contributions, but they’re quietly running the show. A steel block reflects and resonates differently than a die-cast zinc or aluminum bridge. Sloppy threads on bridge studs can weigh in, just as plate-style bridges can couple firmly to the body. Tuning machines can influence not just tuning stability, but their weight can alter the way the headstock itself vibrates.
It’s All Connected
Then there’s the neck joint—the place where sustain goes to die. A tight neck pocket allows the energy to transfer efficiently. A sloppy fit? Some credit it for creating the infamous cluck and twang of Fender guitars, so pick your poison. One of the most important specs is scale length. A longer scale not only creates more string tension, it also requires the frets to be further apart. This changes the feel and the sound. A shorter scale seems to diminish bright overtones, accentuating the lows and mids. Scale length has a definite effect on where the neck joins the body and the position of the bridge, where compromises must be made in a guitar’s overall design. There are so many choices, and just as many opportunities to miss the mark. It’s like driving without a map unless you’ve been there before.
Alchemy, Not Arithmetic
At the end of the day, a guitar’s greatness doesn’t come from its spec sheet. It’s not about the wood species or the coil-wire gauge. It’s about how it all conspires to either soar or sink. Two guitars, built to identical specs, can feel like long-lost soulmates or total strangers. All of these factors are why mix-and-match mods are a long game that can eventually pay off. But that’s the mystery of it. You can’t build magic from a parts list. You can’t buy mojo by the pound. A guitar is more than the sum of its parts—it’s a sometimes unpredictable collaboration of materials, choices, and human touch. And sometimes, whether in the hands of an experienced builder or a dedicated tinkerer, it just works.
Two Iconic Titans of Rock & Metal Join Forces for a Can’t-Miss North American Trek
Tickets Available Starting Wednesday, April 16 with Artist Presales
General On Sale Begins Friday, April 18 at 10AM Local on LiveNation.com
This fall, shock rock legend Alice Cooper and heavy metal trailblazers Judas Priest will share the stage for an epic co-headlining tour across North America. Produced by Live Nation, the 22-city run kicks off September 16 at Mississippi Coast Coliseum in Biloxi, MS, and stops in Toronto, Phoenix, Los Angeles, and more before wrapping October 26 at The Cynthia Woods Mitchell Pavilion in The Woodlands, TX.
Coming off the second leg of their Invincible Shield Tour and the release of their celebrated 19th studio album, Judas Priest remains a dominant force in metal. Meanwhile, Alice Cooper, the godfather of theatrical rock, wraps up his "Too Close For Comfort" tour this summer, promoting his most recent "Road" album, and will have an as-yet-unnamed all-new show for this tour. Corrosion of Conformity will join as support on select dates.
Tickets will be available starting Wednesday, April 16 at 10AM local time with Artist Presales. Additional presales will run throughout the week ahead of the general onsale beginning Friday, April 18 at 10AM local time at LiveNation.comTOUR DATES:
Tue Sep 16 – Biloxi, MS – Mississippi Coast Coliseum
Thu Sep 18 – Alpharetta, GA – Ameris Bank Amphitheatre*
Sat Sep 20 – Charlotte, NC – PNC Music Pavilion
Sun Sep 21 – Franklin, TN – FirstBank Amphitheater
Wed Sep 24 – Virginia Beach, VA – Veterans United Home Loans Amphitheater
Fri Sep 26 – Holmdel, NJ – PNC Bank Arts Center
Sat Sep 27 – Saratoga Springs, NY – Broadview Stage at SPAC
Mon Sep 29 – Toronto, ON – Budweiser Stage
Wed Oct 01 – Burgettstown, PA – The Pavilion at Star Lake
Thu Oct 02 – Clarkston, MI – Pine Knob Music Theatre
Sat Oct 04 – Cincinnati, OH – Riverbend Music Center
Sun Oct 05 – Tinley Park, IL – Credit Union 1 Amphitheatre
Fri Oct 10 – Colorado Springs, CO – Broadmoor World Arena
Sun Oct 12 – Salt Lake City, UT – Utah First Credit Union Amphitheatre
Tue Oct 14 – Mountain View, CA – Shoreline Amphitheatre
Wed Oct 15 – Wheatland, CA – Toyota Amphitheatre
Sat Oct 18 – Chula Vista, CA – North Island Credit Union Amphitheatre
Sun Oct 19 – Los Angeles, CA – Kia Forum
Wed Oct 22 – Phoenix, AZ – Talking Stick Resort Amphitheatre
Thu Oct 23 – Albuquerque, NM – Isleta Amphitheater
Sat Oct 25 – Austin, TX – Germania Insurance Amphitheater
Sun Oct 26 – Houston, TX – The Cynthia Woods Mitchell Pavilion
*Without support from Corrosion of Conformity
MT 15 and Archon 50 Classic amplifiers offer fresh tones in release alongside a doubled-in-size Archon cabinet
PRS Guitars today released the updated MT 15 and the new Archon Classic amplifiers, along with a larger Archon speaker cabinet. The 15-watt, two-channel Mark Tremonti signature amp MT 15 now features a lead channel overdrive control. An addition to the Archon series, not a replacement, the 50-watt Classic offers a fresh voice by producing retro rock “classic” tones reminiscent of sound permeating the radio four and five decades ago. Now twice the size of the first Archon cabinet, the Archon 4x12 boasts four Celestion V-Type speakers.
MT 15 Amplifier Head
Balancing aggression and articulation, this 15-watt amp supplies both heavy rhythms and clear lead tones. The MT 15 revision builds off the design of the MT 100, bringing the voice of the 100’s overdrive channel into its smaller-format sibling. Updating the model, the lead channel also features a push/pull overdrive control that removes two gain stages to produce vintage, crunchier “mid gain” tones. The clean channel still features a push/pull boost control that adds a touch of overdrive crunch. A half-power switch takes the MT to 7 watts.
“Seven years ago, we released my signature MT 15 amplifier, a compact powerhouse that quickly became a go-to for players seeking both pristine cleans and crushing high-gain tones. In 2023, we took things even further with the MT 100, delivering a full-scale amplifier that carried my signature sound to the next level. That inspired us to find a way to fit the 100's third channel into the 15's lunchbox size,” said Mark Tremonti.
“Today, I’m beyond excited to introduce the next evolution of the MT15, now featuring a push/pull overdrive control on the Lead channel and a half-power switch, giving players even more tonal flexibility to shape their sound with a compact amp. Can’t wait for you all to plug in and experience it!”
Archon Classic Amplifier Head
With a refined gain structure from the original Archon, the Archon Classic’s lead channel offers a wider range of tones colored with gain, especially in the midrange. The clean channel goes from pristine all the way to the edge of breakup. This additional Archon version was developed to be a go-to tool for playing classic rock or pushing the envelope into modern territory. The Archon Classic still features the original’s bright switch, presence and depth controls. PRS continues to stock the Archon in retailers worldwide.
“The Archon Classic is not a re-issue of the original Archon, but a newly voiced circuit with the lead channel excelling in '70s and '80s rock tones and a hotter clean channel able to go into breakup. This is the answer for those wanting an Archon with a hotrod vintage lead channel gain structure without changing preamp tube types, and a juiced- up clean channel without having to use a boost pedal, all wrapped up in a retro-inspired cabinet design,” said PRS Amp Designer Doug Sewell.
Archon 4x12 Cabinet
As in the Archon 1x12 and 2x12, the mega-sized PRS Archon 4x12 speaker cabinet features Celestion V-Type speakers and a closed-back design, delivering power, punch, and tight low end. Also like its smaller brethren, the 4x12 is wrapped in durable black vinyl and adorned with a British-style black knitted-weave grill cloth. The Archon 4x12 is only the second four-speaker cabinet in the PRS lineup, next to the HDRX 4x12.
PRS Guitars continues its schedule of launching new products each month in 2025. Stay tuned to see new gear and 40 th Anniversary limited-edition guitars throughout the year. For all of the latest news, click www.prsguitars.com/40 and follow @prsguitars on Instagram, Tik Tok, Facebook, X, and YouTube.