
A view of the mic closet at Nashville’s County Q studio.
Compare notes with Nashville producer-engineer Mike Purcell, who runs down the essentials of a pro-level home-studio mic collection.
A well-rounded mic closet could take a lifetime to build. I’m constantly trying different things, but there’s always a core set of mics I come back to because they’re reliable and provide good results. Many of these mics work on a wide range of instruments. By knowing my mics, I can make a choice that’s going to enhance the sound of an instrument—especially guitar.
In this story, I’ve listed several options for each mic type covering a range of prices from low to high. A higher cost usually indicates that the quality of components and workmanship are better, leading to a more consistent product. Lower cost generally means quality control isn’t as strict and that mics may differ more from their published specs.
You’ve probably heard this before, but the three main types of mics are dynamic (or moving coil), condenser (or capacitor), and ribbon mics. Let’s work our way through each category.
Dynamic Mics
Dynamic mics are composed of a voice coil suspended in a magnet. Incoming sound moves the voice coil within the magnetic field and a current is created. This is passed through a transformer to step up the voltage, and then sent to a mic preamp.
Dynamic mics are the mainstay of live sound because of their durability and ability to be used on loud sound sources without overloading. These are desirable characteristics in the studio when we’ve got to place mics close to a flailing drummer or mike up a Marshall Super Lead 100 full stack.
Dynamic mics exhibit the following characteristics:
- They are less sensitive to transients and high frequencies (7k and up.) They capture these frequencies, but at a lower level than a condenser.
- They color the sound in the midrange between 3-5k, adding a slight bump in this area.
- On loud sound sources, they exhibit a type of mild compression or soft clipping, useful on amps, drums, and vocals.
- They are cardioid, or unidirectional, and are the most sensitive in the front with maximum rejection off the back. (There are divisions of cardioid: hyper, super, etc. In all cases, they are most sensitive at the front, with rejection off the back or sides.)
- They exhibit a proximity effect. As directional mics are placed closer to a sound source, they pick up more low end, 100 Hz and below. Dynamic mics are designed to use the proximity effect, so as they move farther from a sound source, they will sound thinner.
“Dynamic mics are the mainstay of live sound because of their durability and ability to be used on loud sound sources without overloading.”
Even though dynamics all exhibit these same general characteristics, each mic will color the sound differently. Some dynamic mics work better on drums. They have an increased low-frequency response, a dip in the lower mids, and a bump in the presence range—essentially an EQ curve that sounds good on bass drums and toms. Others may have a more pronounced bump in the upper mids, making them a great choice for guitar amplifiers. While dynamic mics are typically used for the close miking of drums and guitar amplifiers, they are also well-suited to some vocalists.
A well-rounded mic closet in a home studio that cuts four- or five-piece bands would have at least 8 to 10 dynamics. Modern production dynamic mics top out around $600, and most are under $250.
Dynamics mics to consider:
- Shure SM57 ($99 street): The most common mic in the world. It’s cheap, incredibly durable, and sonically consistent from mic to mic. It can take the highest sound pressure level (SPL) you can throw at it and work on any instrument in a pinch. It’s often used for snare drums or guitar amps. Many of Tom Petty’s vocals were recorded with an SM57.
- Shure SM58 ($99 street): The big brother to the SM57. It has a built-in pop filter/windscreen and a slightly different low-end response. There are hundreds of cheap knockoffs of the Shure SM57 and SM58. Stick with the originals and you’ll be much happier over the long run.
- Sennheiser e 609 ($99 street): An inexpensive supercardioid mic. The supercardioid pattern indicates it is much more directional than a cardioid. This can be useful when miking a snare drum, to reject sound off the sides of the mic. The e 609 also has a slightly less harsh frequency response, so can be useful on edgy or bright guitars.
- Shure Beta 52A ($199 street), Audix D6 ($199 street), AKG D112 ($229 street): These are a newer generation of dynamic mics that are designed for bass drums. Plus, they work well on toms—although Audix also makes the D4 and D2, which are tailored towards smaller drum frequencies (rack tom, floor tom). And they work well on bass amplifiers.
- Sennheiser MD 421-II ($399 street): Excellent kick and tom microphone. The frequency response of the 421 works well on drums. It’s also commonly used on guitar amps and vocals.
- Shure SM7B ($399 street): Another variation using the SM57/58 diaphragm, this mic has electronics that allow you to tailor its frequency response. The SM7 is often used in broadcast and is a go-to choice for vocals by rap and metal artists.
Side note: Many manufacturers offer a drum-mic package—a great solution if you’re starting out. These usually include several dynamics for the close mics and a few condensers for the overheads and/or hi-hat. Plus, these mics can also be used for recording other instruments.
Here are a few examples of drum packages:
- Audix FP7 ($399 street): A seven-piece mic kit, with five dynamics and two condensers. Audix also offers larger drum packages.
- Avantone PRO CDMK-8 ($899 street): This eight-piece kit includes five dynamics and three condensers.
- AKG Drum Set Premium ($2,329 street): Another eight-piece set, with five dynamics and three condensers.
Condenser Mics
Condenser mics consist of a thin, charged diaphragm suspended over a metal plate. As sounds strikes the diaphragm, it moves and causes electrons to flow through the plate. This signal is amplified by internal electronics and passed through a transformer or field-effect transistor (FET) and is sent to a mic preamp.
Condenser mics exhibit these characteristics:
- They are active devices that require a power source, most commonly provided by +48V Phantom Power.
- Some are capable of multiple polar pickup patterns: cardioid, omnidirectional, figure eight, and everything in between.
- They may include a passive attenuation device (PAD), a switchable attenuator that prevents overload when the mic is used on loud sound sources.
- They may include a switchable high-pass filter (HPF), used to roll off unwanted low-end frequencies.
- They are the most sensitive mics, making them ideal for recording quiet instruments.
- They have the widest frequency response and are good at capturing frequencies across the audible spectrum.
- They color sound less than other mics and are good when you want to accurately capture the timbre of an instrument.
Condenser mics are divided into two categories: small diaphragm condensers (SDC) and large diaphragm condensers (LDC). SDCs have a diaphragm of less than 1" and tend to be more responsive to transients and high frequencies. Their off-axis response is also more even.
LDCs have a 1" or greater diaphragm. They sound fuller, but off-axis mic response can be uneven. LDCs, because of their overall size, can be harder to position in tight miking situations.
“Because of their sensitivity and wide frequency response, condenser mics are used for drum overheads and ambience, acoustic stringed instruments, piano, ensembles, amplifiers, and vocals.”
Matched microphone sets require that the frequency response and sensitivity of the two microphones are very similar. This allows them to record a balanced stereo image. So, a well-rounded mic closet will have a matched set of SDCs and LDCs, and a few assorted condensers for other purposes.
SDCs to consider:
- Rode NT5 ($219 single/$429 pair street): Rode is an Australian manufacturer that makes quality products at affordable prices. I’ve been impressed with all their equipment, and the NT5 is no exception.
- Shure SM81 ($399 street): A good, durable utility mic. Inexpensive. Not as open sounding as other SDCs. I use these for snare bottoms and hi-hats. They have a PAD and HPF.
- Warm Audio WA84 ($399 single/$749 pair street): Warm Audio is a relative newcomer to the pro audio world. They’ve been making reproductions of classic gear and offering them at lower prices. In general, I’ve been impressed with the quality of their products. These PAD-equipped mics are their version of the KM-184, at half the cost.
- AKG C451 B ($639 single/$1,395 pair street): Very responsive to transients and can take high SPL. These PAD and HPF mics yield an edgier sound. I love these on mandolin or banjo.
- Miktek C5 ($699 /$1,399 pair street): These mics include a switchable omni capsule, allowing for cardioid and omnidirectional use for spaced pair miking.
- Neumann KM184 ($849 single/$1,595 pair street): Smooth sounding all-around mic with an articulate and defined high-frequency response. One of my favorite go-to mics when I need a stereo recording of an instrument.
LDCs to consider:
With LDCs, manufacturers have families of mics that use the same basic components, but the higher-end mics will offer pattern selection or other features. Within the family, the sound will be similar. Examples are the AKG C214 and C414, and the Shure KSM32 and KSM44.
- Rode NT1000 ($329 street): I am a huge fan of Rode, and the NT1000 routinely beats out more expensive mics for vocals. This cardioid mic is solidly built and big sounding without harshness..
- AKG C214 ($465 street): The little brother to the AKG C414, this cardioid-only example with a PAD and HPF exhibits the same general frequency response, but it doesn’t have all the features of the 414.
- Audio Technica AT4033A ($399 street): One of my favorite inexpensive mics, the 4033 has a pleasant defined midrange and clarity that brings instruments through the mix. These may not be good when trying to capture extended low frequencies. Audio-Technica calls this cardioid mic a medium-diaphragm condenser.
- Miktek C1 and C7e ($599 and $899 street): Miktek is a Nashville-based manufacturer that has developed a line of mics that perform far outside their price class. The C1 has a PAD, HPF, and is cardioid only, while the C7e is multipattern.
- Neumann TLM 103 ($1,195 street): The TLM 103 is a smaller footprint package that utilizes Neumann’s classic U 87 capsule and transformer-less circuitry at a more affordable price. These sound great on vocals and acoustic stringed instruments, if you’re looking for a bigger sound.
- AKG C414 ($1,279 street): The 414 is another industry standard found in many studios. Based on the classic AKG CK12 capsule, the 414 has a wide frequency response. It is bright and present and can sound amazing on some singers and overly bright on others. It works well on pianos and acoustic guitars where you need a sheen on them.
- Neumann U 87 Ai ($3,695 street): The U 87 is a flagship standard that you can find in almost any studio. Multipattern select, HPF and PAD equipped, it’s got a fat low end, smooth high frequencies without harshness, and a thick, musical midrange. An incredibly flexible mic with excellent fidelity, it’s got a price tag to match its functionality. I’ve used these on toms for a huge sound, but you have to really trust the drummer if you’re putting this mic in range of their sticks
Ribbon Mics
Ribbon mics function by suspending a very thin conductive metal strip between two magnets. Sound waves strike the metal strip, causing it to vibrate. The vibration in the magnetic field creates a current in the magnets. This is sent through a transformer, and then the signal is sent to a mic preamp.
“Never run +48V phantom power to a ribbon mic. While most modern ribbons are phantom safe, it can destroy vintage ribbon mics.”
A good mic closet should have several ribbon mics, and possibly more depending on the style of production. Ribbon mics have seen a resurgence over the past 20 years and there is a wide variety available, ranging from $200 to $1,500 and more. Ribbons are used on guitar amps, as drum overhead or room mics, and on horns, acoustic guitars, percussion, and vocals.
Ribbon mics exhibit these characteristics:
- The thin ribbon allows them to be very sensitive to transients.
- They color the sound. They are warm sounding and add character.
- They are the least sensitive type of mic and ill-suited for quiet sound sources.
- They’re very fragile. A puff of wind (or the air coming out of a kick drum) can damage the mic.
- They are bi-directional/figure eight. They pick up sound from the front and back of the mic at the same level. Exceptions exist, like the Beyerdynamic M 160.
- Caution: Never run +48V phantom power to a ribbon mic. While most modern ribbons are phantom safe, it can destroy vintage ribbon mics. (Once again, there are exceptions. Active ribbon mics, like the AEA N22 Nuvo, exist. These do have internal amplification similar to a condenser and require phantom power.)
Ribbon mics to consider:
- Pinnacle Microphones Fat Top ($229/$519 pair street): The Fat Top is a current iteration of the original Cascade Fat Head. I’ve used Fat Heads for years. They’re wonderful on guitar amps and percussion.
- Stager SR-66/SR-2N ($699/$649 street): Stager Microphones is a small boutique operation in Nashville. They use neodymium magnets in these models, for increased magnetism in a lighter package. The transformers are hand-wound and designed to get the best transfer of sound from ribbon to mic preamp. The SR-66 is a long-ribbon package, offering a flatter frequency response. The SR-2N is a midrange-forward short-ribbon design.
- Coles Electroacoustics 4038 ($1,485 street): The Coles 4038 is designed by the British Broadcasting Corporation in the 1950s and the tech specs have never changed. A lot of work went into engineering this mic. It has a flat frequency response up to 15k and is very responsive to transients.
- Royer R-121 ($1,499 street): Royer Labs is one of the best-known manufacturers of ribbon mics. They’ve pioneered innovations in ribbon mic technology that allow them to be used on very loud sound sources without damage to the microphone. The R-121 is one of the most popular mics in existence and exhibits all the classic characteristics of a ribbon mic.
What about tube microphones?
Tube mics are a subset of condenser mics. Up until the 1960s, condensers used a tube for the amplification of the low-level diaphragm signal. Tubes sound nice, but have a lot of issues: heat, high power requirements, and they can suffer from microphonics. In the ’60s, a solid-state replacement for the tube was created: the FET, or field effect transistor. The FET emulates tube characteristics and has two benefits: smaller size and reduced power requirements. The first solid-state condenser mic designs used the same circuit except for the FET substitution, but they sounded different, crisper. They had lost the tube character.
Tube mics are revered for their warmth, wide frequency response, and pleasing sound. They are most commonly used for vocals, but I’ve used them for every instrument. There’s a robust market for inexpensive tube mic modification. Sometimes it’s as easy as swapping a tube, while others do capsule and component level changes. These mods can greatly enhance the sound of an inexpensive tube mic. A good mic closet should have at least one curated tube mic. They start at about $499 and can range upwards of $30,000.
Some manufacturers with tube mics in the below-$1,000 price range include Avantone, Warm Audio, Golden Age, and Lauten Audio. My recommendation is to audition several and find the one that will have the broadest application for your recording situation. They won’t sound exactly like their pricier counterparts, but they’ll give you a flavor in your mic closet that’s only possible with a tube microphone.
Tube mics to consider:
- Mojave MA-300SN ($1,399): Mojave was created by David Royer of Royer Labs. They use quality components for mics that meet exacting standards. The 300SN is a tube large-diaphragm condenser mic. It features a continuously variable pattern select, which ranges from omni to figure eight. The MA300SN has a warm low end with an open top.
- Miktek CV4 ($1,699 street): Miktek’s line of hand-built mics includes this large diaphragm condenser with nine polar patterns. I’ve used these on vocals and stringed instruments with great success.
- Peluso 22 47 SE ($2,149 street): Peluso Microphone Lab is a boutique company that hand builds each mic. The 22 47 is a reproduction of the venerable Neumann U 47. The 22 47 is a great choice for vocals and acoustic instruments, and I find myself using less EQ when recording with this mic. Their interpretations of other classic mics are also available.
Photo by Nick Sonsini
- Telefunken ELA M 251 (repro: $10,996/vintage: $25,000-plus street): Around 3,700 units of the original 251 were manufactured from 1960 to ’65, but a modern reproduction is available. It has an open top end without harshness, a smooth, rich midrange, and low-end warmth with punchiness. It’s an excellent vocal mic and excels on harmonically rich instruments.
Now, Go Forth and Record
You’ve got to start somewhere when building your mic closet. If you’re not tracking full bands, I’d recommend starting with a couple dynamics (like the SM57) and a set of LDCs. With these mics, you’ll be able to cover basic overdub sessions. From there, borrow mics from friends, explore the world of ribbon and tube mic sounds, and discover what works best for your home studio.
What About DIs?
Direct boxes, or DIs, are an integral part of any studio. They are used to connect (Hi-Z) instruments with low-impedance (Lo-Z) microphone preamps. Hi-Z devices, such as guitars and basses, have 1/4" outputs. The DI provides a 1/4" input to connect to your guitar and an XLR output which connects to a preamp. DIs also have a 1/4" output jack. This is used to pass the signal through the DI and connect to an amplifier. Often, a bass or guitar is recorded to two tracks—one signal from the DI and the other from an amplifier.
There are two types of DIs: passive and active. Passive devices have of an internal transformer that changes the impedance of the signal. Active DIs require a power source for their internal electronics and will have less signal degradation than a passive device. A good home studio should have at least one active DI and two passive DIs.
Modern DAW interfaces usually have built-in Hi-Z inputs via 1/4" jacks that allow you to connect directly to your interface. These negate the need for a DI.
Here are several DI boxes to consider:
- Radial StageBug S-B2 ($89 street): Radial is well known for their technology in direct box design. This is a passive DI with a small footprint.
- Radial Pro48 ($129 street): These active devices are full-range DIs with a bandwidth of 20 Hz to 20k.
- Rupert Neve Designs RNDI-1($299 street): Like most Neve designs, this active device is engineered for the highest fidelity audio and sounds great.
Digital Modeling Mics
Digital microphone modeling systems are a relatively new development. They combine a specially designed microphone with modeling software that allows you to record audio that sounds as if you had used a different microphone. The software models a variety of classic or vintage mics. The two frontrunners in this new tech are the Slate Digital VMS Virtual Microphone System and Universal Audio’s Sphere L22 Microphone Modeling System (which was developed in conjunction with Townsend Labs).
They use a sonically transparent microphone designed to interface with their modeling software. The signal is passed from the mic through a neutral mic pre (one that doesn’t color the sound too much) to your DAW input. The plugin is applied to the audio and an output mic model is selected. The result sounds as if it had been recorded with the selected mic.
Slate and UA accomplish this by testing and measuring a microphone’s behavior and mapping that behavior out in software. The software knows the characteristics of the recording mic and processes the audio, applying the differences to the signal. The recorded signal now sounds as if it was recorded with a $20,000 Neumann U 67 (or whichever mic you’ve selected).
The benefit of these systems is that it is non-destructive. Just like amp modeling plugins, there is a dry sound recorded in your DAW, and the processing is applied with a plugin. You have the ability to modify it throughout the recording process, finding the sound that works with your final production.
These systems offer a huge range of sounds and offer mic selections that would not be available in your average home studio. And each system offers a selection of recognized mic models with an established track record.
The lowdown:
• Slate Digital VMS Virtual Microphone System (mic and software $499 street): This system’s ML-2 is a small diaphragm mic. Once recorded, sound is processed via the VMS plugin (compatible with AAX, VST2, VST3, and AU formats). The VMS software includes 13 mic models, ranging from the AKG C12 to the Shure SM7B. Two add-on mic bundles are available for purchase from Slate: Blackbird Mics ($199 street), featuring five mics from Nashville’s Blackbird Studio, and Classic Tubes ($299 street), featuring five modeled mics.
• Universal Audio Sphere L22 Microphone Modeling System ($1,199 to $1,499 street): UA’s Sphere L22 was developed in conjunction with Townsend Labs. The Sphere software works the same as VMS, tuned for the provided mic and offering 34 output mic models.
The Sphere system uses a dual-capsule mic. This allows the software to take the signal from both capsules and create a 3D sonic picture of the modeled microphone. In theory, this should offer off-axis behavior similar to the originals. The mic can use both capsules to create a stereo recording, too.
The software is available in UAD, AAX, VST2, VST3, and AU formats. It offers more tweakable parameters than the VMS. So, if you’re a knob twister and like to fine-tune your sounds, the Sphere is a good choice. The additional controls come with a higher price tag.
- Tone Tips: Modelers vs. Traditional Rigs, Part 2 ›
- Amp Mic’ing vs. Impulse Responses ›
- The Recording Guitarist: Mic Makes Right ›
- Color Coding Sessions Can Save Your Butt - Premier Guitar ›
- How to Get More Out of Your Mics with Modelers - Premier Guitar ›
Bonnaroo announces its 2025 lineup featuring Luke Combs, Hozier, Queens of the Stone Age, Avril Lavigne, and more.
This year features headline performances from Luke Combs on Thursday, Tyler, The Creator on Friday, Olivia Rodrigo on Saturday, and Hozier on Sunday. Further highlights include John Summit, Dom Dolla, Avril Lavigne, Glass Animals, Vampire Weekend, Justice, Queens of the Stone Age, and the first-ever Roo Residency with King Gizzard & the Lizard Wizard performing three sets over three days. In addition, Remi Wolf will lead the “Insanely Fire 1970’s Pool Party” 2025 SuperJam, Bonnaroo’s legendary tradition. The complete Bonnaroo 2025 lineup is below.
Bonnaroo tickets go on sale tomorrow, Thursday, January 9 beginning at 10 am (CT) exclusively via bonnaroo.com. Guaranteed lowest-priced tickets are available during the first hour of sales, from 10 am - 11 am (CT). 2025 ticket options include 4-Day General Admission, 4-Day GA+, 4-Day VIP, and 4-Day Platinum, along with a variety of camping and parking options starting at just $25 down with a payment plan.
The 2025 festival will offer some exciting new features for Bonnaroovians, including the “Closer” RV and Primitive Camping accommodations that guarantee closer proximity to Centeroo, regardless of which day fans choose to enter The Farm. Among this year’s most exciting additions will be The Infinity Stage, a brand-new, one-of-a-kind venue – presented in partnership with Polygon Live – boasting spatial sound, synchronized lights, and an unprecedented three-dome, open-air design to create the world’s largest, most immersive, 360° live music experience.
Bonnaroo also offers upgraded ticket types for those who prefer an elevated experience. GA+ tickets include unlimited access to the Centeroo GA+ Lounge, with relaxed seating, dedicated food for purchase, air-conditioned restrooms, and hospitality staff to assist with all festival needs; a private bar with drinks for purchase plus complimentary soft drinks; complimentary water refill station; a dedicated premium entrance lane at both gates into Centeroo, and more. VIP and Platinum guests will enjoy the same perks plus additional exclusive upgrades, including dedicated close-in and on-field viewing areas; unlimited access to VIP and Platinum Lounges; express lanes at the Festival Store, commemorative festival gifts, and so much more. To learn more about VIP and Platinum, please seehttp://www.bonnaroo.com/tickets.
A wide range of Camping & Parking options will be available in Outeroo including Primitive Car Camping, Glamping, RVs, Backstage Camping, Accessible Camping, Groop Camping, Community Camping, and more. Premium Outeroo Camping Accommodations include pre-pitched Souvenir Tents, cool and comfortable Darkroom Tents, weatherproof Luxury Bell Tents, and spacious 2-person Wood Frame Safari Tents for the ultimate Bonnaroo camping experience. Cosmic Nomads On-Site Daily Parking passes will be available for ticketholders not camping. For details on all accommodation options, please visitwww.bonnaroo.com/accommodations.
Complete Lineup
THURSDAY, JUNE 12
Luke Combs
Dom Dolla
Sammy Virji
Marcus King
Green Velvet
2hollis
Insane Clown Posse
Joey Valence & Brae
Daniel Donato's Cosmic Country
Wilderado
Max Styler
Azzecca
The Lemon Twigs
Wisp
Sofia Isella
Kitchen Dwellers
Dogs In A Pile
Die Spitz
Hey, Nothing
The Droptines
FRIDAY, JUNE 13
Tyler, the Creator
John Summit
Glass Animals
Tipper
Goose
The Red Clay Strays
Rainbow Kitten Surprise
Megadeth
Wallows
Foster the People
Slightly Stoopid
Flipturn
Of the Trees
JPEGMAFIA
Marina
Tape B
MJ Lenderman
BossMan Dlow
INZO
Levity
Mannequin Pussy
Leon Thomas
Cults
Aly & AJ
Matt Champion
Detox Unit
Rachel Chinouriri
Eater
Ginger Root
Bebe Stockwell
Effin
SATURDAY, JUNE 14
Olivia Rodrigo
Avril Lavigne
Justice
Nelly
GloRilla
Mt. Joy
RL Grime
Beabadoobee
Tyla
Jessie Murph
Modest Mouse
Gorgon City
Flatland Cavalry
Hot Mulligan
Action Bronson
Crankdat
Dope Lemon
Gigi Perez
Wave to Earth
Claptone
Jade Cicada
What So Not
Daði Freyr
Ziggy Alberts
ROSSY
Destroy Boys
The Stews
Thee Sinseers & The Altons
AHEE
SUNDAY, JUNE 15
Hozier
Vampire Weekend
Queens of the Stone Age
LSZEE
Remi Wolf
Raye
Royel Otis
Dispatch
Role Model
Barry Can't Swim
Treaty Oak Revival
Big Gigantic
Jack's Mannequin
ATLiens
Bilmuri
Saint Motel
James Arthur
Alex Warren
Zingara
Natasha Bedingfield
Alexandra Kay
Goldie Boutilier
Grace Bowers & The Hodge Podge
GorillaT
YDG
SPECIAL PERFORMANCES
King Gizzard & the Lizard Wizard Roo Residency: 3 Sets, 3 Days (Friday, Saturday and Sunday)
Remi Wolf’s Insanely Fire 1970’s Pool Party Superjam (Saturday)
Enhance your Ratio Machine Heads with Graph Tech's new Barrel Knobs. Designed for comfort and style, these barrel-shaped tuning buttons offer a fresh look and feel to your instrument. Available in chrome and black finishes, these knobs are the perfect way to personalize your guitar.
Graph Tech Guitar Labs has introduced the latest addition to their Ratio Machine Head family: Barrel Knobs. These barrel-style tuning buttons bring a fresh look and feel to the Ratio system, offering players a new way to personalize their instruments – and an easy-to-grip alternative to more traditional tuner knobs.
Available in two different finishes – chrome and black – the new barrel knobs can be ordered as a standalone option. If you already own Ratio Machine Heads, simply order the Barrel Knobs and swap them out – the process is easy and only takes a few minutes. Best of all, there is no need to replace the entire Ratio tuner system.
The new Barrel Knobs were developed at the request of guitarist Thomas Nordegg, known for his work with rock legends like Frank Zappa and Steve Vai. A longtime fan of Graph Tech’s Ratio machine heads, Nordegg saw an opportunity to enhance the system’s ergonomic design and approached Graph Tech with the idea of creating barrel-style tuning buttons to provide an alternative option for players seeking a fresh look and feel. Designed to integrate seamlessly with the Ratio system, these knobs combine ergonomic comfort with understated style, giving players another way to personalize their instruments.
More and more players are option for Ratio Machine Heads on their instruments. Ratio Machine Headsare designed with gear ratios that are uniquely calibrated for each string, making tuning consistent andpredictable across the fretboard. This innovative system simplifies fine-tuning and alternate tunings, saving time and improving accuracy.
Here’s what the new Barrel Knobs offer:
- Refined Functionality: Barrel-shaped design for a natural grip and precise adjustments.
- Timeless Aesthetic: A sleek, modern look that complements any guitar style.
- Perfect Fit: Designed specifically for Ratio Machine Heads, ensuring flawless compatibility.
- Available in chrome and black to suit a variety of instruments and player preferences.
Graph Tech’s new Barrel Knobs are available for $3.00 each and are available in chrome and black finishes.
For more information, please visit graphtech.com.
Neural DSP introduces Archetype: Rabea X, a revamped plugin featuring updated effects, amps, and the Overlord Synth. With a redesigned UI, additional speaker option, and optimized performance, this plugin offers a wide range of tonal options for guitarists.
Neural DSP today announced the introduction of Archetype: Rabea X, a reinvention and reimagining of the original Archetype: Rabea plugin, another in Neural DSP’s celebrated series of collaborations with the world's most creatively and technologically adventurous guitarists.
Rabea Massaad, as both a solo artist and a member of innovative bands Dorje and Toska, is the quintessential modern musician, as at home on YouTube as he is on the fretboards of guitars. He’s also a teacher, the creator of dozens of instructional and informational videos on playing, performing, and gear. That same artistic versatility that was originally captured with Neural DSP’s acclaimed Archetype: Rabea is now taken to new heights via the Archetype: Rabea X plugin. It offers updated takes on key processors that are critical parts of his sound, including Octaver, Fuzz, and Overdrive effects, as well as stereo Delay and Reverb effects with their own unique parameter controls.
Archetype: Rabea X features a unique and innovative suite of amps and effects, as well as the groundbreaking Overlord Synth. There’s also a new speaker option, a redesigned UI, two new noise options for the oscillators (White & Pink), a portamento Glide knob for smoother transitions between notes, and Quad Cortex compatibility via a future CorOS update. All told, this plugin embodies the uncompromising creativity that defines Rabea’s artistry.
"Rabea is a brilliant guitarist, musician, and teacher all in one, and that’s what we’ve set out to do with Archetype: Rabea X — bring that brilliance to other musicians in a way that’s authentic and accessible,” said Douglas Castro, Neural DSP Technologies CEO. “It’s an incredibly versatile plugin, distilling his sonic vision and designed to offer a wide variety of options for players in search of his unique tonal. Today, we proudly present to you, Archetype: Rabea X.”
What's New
- Revamped Overlord Synth: Updates include a fully redesigned UI with visual waveform representations for a more intuitive tone-shaping experience, two new noise options for the oscillators (White and Pink), and a Glide knob for smoother transitions between notes.
- Additional Speaker: The cabinet for the Lead Amp now includes a V30 speaker, offering expanded tonal versatility.
- Redesigned UI: A refreshed interface with updated visuals offers an intuitive, user-friendly experience.
- Optimized Performance: Enjoy faster, smoother, and more responsive functionality.
- Updated EQs: The onboard 4-band semi-parametric equalizers for the Clean, Rhythm, and Lead amps now include high and low-pass filters.
Pre Effects
Featuring a Dual Compressor, Octaver, Fuzz, and Overdrive to cover everything from chimy blues to colossal distortion. Use the vintage/modern switches on the Octaver, Fuzz, and Overdrive to toggle between independent algorithms with era-appropriate characteristics.
Amps
Three remarkable amplifiers meticulously tweaked with Rabea to deliver a world of vintage and modern tones.
- Clean: Traditional Cali cleans with added modern chime, this simplistic amp is truly one for the classic players.
- Rhythm: An all-rounder by no exaggeration! This amplifier excels at edge-of-breakup, searing gain, and everything in between.
- Lead: An incredibly malleable modern high-gain amplifier, delivering all the tight or saggy chugs you could ever possibly desire.
Cabsim + IR Loader:
A comprehensive cabsim module with IRs captured by Neural DSP. Featuring six virtual microphones that can be easily positioned around the speakers. In addition to the included IRs, this module can be used to load your own impulse responses.
Room Reverb
The Room Send controls in the cabsim module introduce a subtle room reverb effect, adding natural depth to your sound.
Post Effects
With somebody as renowned for their abundant use of delay and reverb as Rabea, Neural DSP crafted the plugin’s post-effects section to deliver exceptional tonal versatility:
- Stereo Delay: As analog as you can get in a plugin! This delay features all the usual parameters you’d expect, with Icicles and Cross-feed controls for infinite dreamy delay sounds. Toggle the pre/post switch to position the delay before the amplifier for a vintage approach to tone crafting.
- Reverb: Vast, rich, and endlessly expansive, just as you’d imagine! Hit the Freeze button while playing a chord to suspend it in space, transforming it into a pad you can jam over while using the independent “Volume” and “Pitch” controls to change its sound.
Operation Overlord
Archetype: Rabea’s legendary Overlord Synth — a full-featured subtractive monosynth playable with any standard guitar (no keyboard or MIDI programming required!) — has received significant updates. These include a fully revamped UI with visual waveform representations for more intuitive tone-shaping, two new noise options for the oscillators (White and Pink), and a Glide knob for smoother transitions between notes. You’ll also retain its fantastic features, such as proprietary note triggering, pitch tracking, and envelope tracking algorithms, enabling seamless synth control with your guitar.
“Archetype: Rabea X is the next step in Neural’s dedicated mission of creating flawless virtualizations of the world’s most amazing and creative guitarists,” concluded Dan Davies, Neural DSP Technologies Chief Marketing Officer. “We worked tirelessly to assure that users of Archetype: Rabea X will enjoy the full Rabea experience!”
The new Archetype: Rabea X plugin is free as an update to existing Archetype: Rabea plugin users. New users can get 30% off Archetype: Rabea X from December 18th, 16:00 EET, until January 6th, 16:00 EET.
For more information, please visit neuraldsp.com.
The Spring King Junior follows in the footsteps of the original Spring King reverb, however, with a much smaller footprint.
Building on a 25-year legacy, Danelectro has launched the brand new Spring King Junior reverb pedal.
"Danelectro’s new Spring King Junior offers authentic reverb from a real built-in spring tank…but in a more compact pedalboard-friendly size. And the Spring King Junior passes the ultimate spring reverb test with flying colors: bump it and you’ll get thunderous reverb sound, just like vintage spring reverbs."
Spring King Junior features include:
- Built-in spring reverb tank
- True bypass soft switching
- Two knobs for controlling reverb Depth and Tone
- Standard 9-volt DC input; no battery compartment
- Rugged die-cast case measuring 2-1/2” wide x 6” long x 2-1/8” high
Danelectro’s Spring King Junior carries a street price of $199.