
The reclusive pedal builder discusses the origins of his famed Centaur overdrive, the more affordable new KTR design, and how one pedal can inspire so much adoration and disdain.
If you've spent any amount of time on guitar-gear forums, you know they can often devolve into pretty abrasive battles of opinion. Even when a thread starts out with the best of intentions, it's not uncommon for it to morph into the online equivalent of a mythical Hydra. Forum administrators attempt to clean things up and lock out the more abusive commenters, but once they cut off one of the creature's heads, two more appear.
Of all the forum topics that can inspire such heated debate, few inspire more passion, awe, and vitriol than a guitar pedal named after a different sort of mythological creature. Launched in 1994 at the front end of the modern-day boutique-pedal boom, the Klon Centaur overdrive was immediately met with critical acclaim. So much so that it's ironic how much the pedal named after the half-human, half-horse creatures from Greek legend has since developed such a complex mythology of its own. And the fact that this seemingly mundane, 3-knob stompbox is used by such high-profile players as Jeff Beck, John Mayer, Joe Perry, Nels Cline, and Matt Schofield only compounds matters. Never mind the fact that the majority of the circuit comes encased in epoxy.
We recently spoke to Klon's Bill Finnegan about the origins of the Centaur, his new KTR design—which made a (naturally) limited debut in October of 2012—and how an overdrive pedal can fetch more than $1,000 on the used market and inspire such emotionally charged reactions.
Birth of a Centaur
In the 1980s, Bill Finnegan played in a band where he plugged his Telecaster straight into a Twin Reverb turned up as loud as the soundman would permit. In bigger Boston-area clubs, the Twin's volume would be at 6 or sometimes even 7, but in smaller places Finnegan could usually turn it up to only 3 1/2 or 4. The latter still sounded good, but not as harmonically rich as when the amp was working harder. Although it didn't occur to him at the time, a pedal that would give him the sound of a cranked amp is exactly what he needed.
Finnegan recalls that, in 1990, guitarists began chasing after out-of-production Ibanez Tube Screamers in droves. He'd heard about a guy who was selling two TS9s, and—hoping one of the little green pedals would help make his Twin sound like it was at 6 when it was only at 4—he went to check them out. It immediately became clear that Tube Screamers were not for him.
Finnegan built Centaurs—around 8,000 in total—by hand, on a cheap folding card table in a succession of small apartments for 15 years.
“[The TS9] compressed the transient response of the original signal a lot, had a midrange character I didn't like, and subtracted a noticeable amount of bass response from the signal as well," he explains. The same seller also had a TS808 that he wasn't selling. And, though Finnegan thought it sounded a little better than the TS9s, he still felt it had the aforementioned shortcomings. What he really wanted was a big, open sound, with a hint of tube clipping—a sound that would make you unaware a pedal was involved.
That's when Finnegan starting looking into creating a new design that would meet those criteria. He recruited a friend who'd just graduated from MIT with an electrical engineering degree. Though both had day jobs, for the next couple of years they got together once a week and tried to push the ball down the field. Within the first year, they'd developed prototypes that were much closer to what Finnegan wanted than a Tube Screamer, and various guitarists in the Boston area encouraged them to go into production so they could buy their own. But Finnegan felt the circuit could still be improved, so he and his partner kept working.
Eventually, the MIT friend bought a house in the suburbs and the distance made it harder to work together. Finnegan later partnered with the late Fred Fenning (who tragically passed away in a plane crash in the mid '90s)—another MIT grad whom Finnegan says was brilliant and very determined. Although Fenning had never designed an audio circuit and had no real interest in music, he was exceptionally good at finding ways to give the circuit what Finnegan thought it needed at any given time. Finnegan says Fenning deserves a lot of credit for the circuit in both the Centaur and its successor, the KTR.
Photo by Sarah Pollman
The entire design process took four and a half years, and when the pedal debuted at the end of '94 Finnegan was soon very busy trying to keep up with the demand—building, testing, and shipping the pedals as a single-man outfit.
Evolution of the Legend
From that point on, demand for Centaur pedals grew. Finnegan says he typically worked 55–60 hours per week in effort to keep turnaround times as short as possible, though he was hindered by the fact that the circuit was very labor intensive and time consuming. He also says it was more expensive to build than most other pedals due to the fact that everything from its cast enclosure to its knobs, pots, and sheet-metal bottom were custom crafted. Finnegan estimates the aggregate cost of a Centaur as seven to eight times that of a pedal built with off-the-shelf parts.
“For the last seven years or so of Centaur production, the retail price was $329," says Finnegan, “and to be honest, my profit margin was not very sensible—no real business person would have considered, for more than a moment, doing what I was doing for the return I was receiving. Also, given that I live in Boston, it was impossible for me to hire people and expand: Real estate here is in short supply and very expensive, so there was no possibility of my renting commercial space to set up an actual shop."
Finnegan built Centaurs—around 8,000 in total—by hand, on a cheap folding card table in a succession of small apartments for 15 years. In addition to the modest returns from his efforts, Finnegan says he felt immense stress as he tried to oblige those who wanted a Centaur but didn't want to pay the inflated price used specimens were fetching because of the 12- to 14-week turnaround time for a new one. It gradually became clear to Finnegan that the situation was unsustainable.
“These two photos show my testing jig for Centaur boards, with one of my experimental boards on it," Bill Finnegan shares. “The experimental boards have sockets for every component in the circuit, which enables me to listen to any particular component and then swap it out for a substitute while keep everything else the same. This experimental board is the one I used for developing the KTR. Unlike the Centaur which had through-hole components with leads, I wanted to use surface-mount components for the KTR, which meant that my assistant, John Perotti, and I had to spend an enormous amount of time soldering through-hole leads onto hundreds of very small surface-mount components so that we could evaluate them and choose the ones that would make the KTR sound the same as the Centaur did."
Photo by Nolan Yee.
“I was going to have to kill it before it could kill me," Finnegan recalls. In 2008, he began working on a ground-up redesign that had to meet the following criteria: It had to be straightforward to build, so that any good contract manufacturing firm would be able to do the job easily and well. It had to be rugged and reliable. It had to be a design with no hookup wires whatsoever, and with a modular footswitch assembly so that faulty footswitches could be replaced in a few minutes. It had to be considerably smaller than the Centaur. Except for the all-important clipping diodes, it had to have surface-mount components, which take up less space on a board than traditional through-hole components. Finnegan also wanted to prove—to himself and to those who said it couldn't be done—that, with careful component selection and smart board layout, he could design a successor that would sound exactly the same as the Centaur.
“This turned out to be quite a challenge," Finnegan says. “My assistant, John Perotti, and I spent almost two years listening to different surface-mount capacitors in various places in the circuit before I felt this had been achieved." Lastly, he wanted the new unit to be visually unique—a tall order, given that the unit would be housed in a standard enclosure.
I don't have any overall preference for single-coil guitars or humbucker guitars myself. I like pretty much everything under the sun in the way of electric guitars, and over the years I've owned a bunch of very different ones.
The one new feature Finnegan wanted to incorporate was a switch that enabled the player to choose the buffered output of the original Centaur or a true-bypass output. “Without the buffer there is a very noticeable degradation of the signal due to the capacitance inherent in guitar cables," says Finnegan, “but some people prefer it, so I wanted to provide that option in the new unit." He quickly adds, “My good friend Paul Cochrane—of Tim and Timmy [pedals] fame—was the guy who designed the switching circuitry, so a tip of the hat to Paul."
It took a long, long time to finish the KTR. And though Finnegan says it was much more difficult than he expected, he feels it has achieved all of his design objectives. “It sounds the same as the Centaur, takes up considerably less space on a pedalboard, is less expensive, and it's distinctive aesthetically—it's got the Klon thing going on." He laughs, “Whatever the Klon thing is."
You obviously have high expectations from your designs, though you're also perplexed by the reactions it inspires. What do you want people to see in Klon?
What I want people to expect from me and from Klon are designs that are exceptional in the literal sense of the term—designs that are conceptually sound and well executed. Designs that are unique and not to be expected from any other designer, no matter how talented.
When you were designing the Centaur, did you begin with any assumptions about players who'd be interested in it?
I was working from the assumption that there were a lot of guitar players with really good guitars and really good amps who were looking for an overdrive pedal that—whether it was adding dirt or not itself—wouldn't mess up what they already had and liked. Given the popularity of the Centaur and now the KTR, I would say that this has been borne out.
In your opinion, do the pedals work better with single-coils or humbuckers?
Neither. I don't have any overall preference for single-coil guitars or humbucker guitars myself. I like pretty much everything under the sun in the way of electric guitars, and over the years I've owned a bunch of very different ones. Each of them has its own particular thing going on, and when I was working on the design of the circuit I was always thinking about how it could be more effective in preserving and accentuating the essence of whatever instrument it was receiving the signal of.
What can you tell us about Centaur units that occasionally turn up on eBay with the claim that they are “new, with full warranty"—are they fakes?
I have a very close friend who is a single mom and whose job doesn't pay all that well. Every now and then she needs a little help, financially. I'm aware of what the used units are selling for, so at some point after I discontinued the Centaur it occurred to me that—if and when she needed me to—I could build a Centaur and give it to her to sell on eBay and use the proceeds to keep going. This has worked really nicely, and I'll continue to do it for as long as my old Centaur parts last. Since I discontinued the Centaur, a lot of people have asked me whether I'd consider building one for them—sometimes offering me pretty substantial amounts of money—but I'm not going to do that. The only Centaurs I build anymore are the ones I build for her, and I don't make or collect a single cent from them.
Klon builder Bill Finnegan wanted to include this text—which refers to the dialogue surrounding his famed Centaur design—on the casing of his new KTR pedal. “It's a wry observation that I can't be held responsible for the overheated emotions that have been introduced into various Klon debates since the earliest days of the Centaur," he says. “I knew that in using that text I'd be stirring things up some, but I thought it would be interesting and fun to see how, in reacting to it, people would self-select into either the 'love it' or the 'hate it' group."
Photo by Nolan Yee.
Do you think Centaurs will retain their high value now that the KTR is available?
Yes, in general I think they will. They're collectible and—with the one small exception I just mentioned—no more will be built, unless I'm very mistaken. For almost everyone, the KTR is a much more sensible option now: It sounds the same, it's much smaller, it's way the hell less expensive—$269 retail—and you don't have to worry about losing something that's worth $1,000 or $1,500 or $2,000 if it's stolen. On the other hand, the Centaur has something of its own that people really like and are willing to pay serious money for. The design has achieved a certain status—I would use the analogy of old, custom-colored Marshalls. I have two small-box, 50-watt Marshall Lead heads—model 1987s: One is a black-Tolex, aluminum-panel head from 1970, and the other is a red-Tolex, plexi-panel head from 1969. They have the same circuitry and sound almost identical, but of course the red one is worth way more than the black one. I like cool, distinctive things as much as the next guy, so I'm not in a position to criticize someone for being willing to pay more than I myself would, or more than most people would, if they want it that much.
What are the demographics of the typical Klon user?
It seems to be more or less everyone. Baby-boomer guys who are still only interested in the music they grew up with, but also a lot of younger, indie-rock people, and also a number of musicians whose work is more experimental and can't be easily categorized.
What can you tell us about the germanium diode you like so much in your circuits?
In 1993 and '94, when it was clear that Fred and I were getting close to producing what I thought was the full measure of what our circuit was capable of, I started buying quantities of every diode I thought might be at all suitable for the head-to-toe pair that clips the signal, except for when the circuit is in clean-boost mode. This was pre-internet, so I was going to the public library, looking up distributors in the Thomas Register, and then calling those distributors to find out what they had—email was still in the future then! I started out ordering both germanium and silicon diodes, but pretty quickly I began concentrating on the germaniums. Usually, though not always, they sounded more natural to me than the silicon ones did. After months and months of listening, I felt a particular new-old-stock germanium diode sounded best in the circuit, so I thought I should buy as many of those as I could afford. Eventually, I found a distributor that had a significant quantity of them. They were stocking them for a huge OEM, who—without any warning, I gather—stopped using that part. I bought them all at a good price. The distributor was thrilled to be able to sell them and not have to eat them.
Does the KTR have the same diodes?
Yes, the KTR has the exact same NOS diodes as all Centaurs did.
Since I discontinued the Centaur, a lot of people have asked me whether I'd consider building one for them—sometimes offering me pretty substantial amounts of money—but I'm not going to do that.
What is it you like about the sound of that diode when it clips?
It's a little more complicated than that, because the diode clipping happens on top of some op-amp clipping in the main gain stage. So it's op-amp clipping, then diode clipping. But to answer your question, this particular diode in the head-to-toe pair in the circuit just produces a very natural-sounding distortion in terms of the harmonic response. It's not harsh, but it also doesn't round off the highs excessively. It doesn't compress the signal as much as many germanium diodes seem to, but on the other hand it provides a little bit of what—to me—is exactly the right kind of compression.
Which other pedal makers are using this particular diode?
To the best of my knowledge, no one. It's a part that's been out of production for decades now, so even if someone else could identify it, I seriously doubt they'd be able to find any—I've tried a number of times myself.
So what are you working on now?
Lately, I've been focused almost entirely on putting together a good long-term arrangement for production of the KTR. This kind of thing has always been more of a challenge for me than it seems to be for anyone else, but I admit that I do have requirements—particular things I insist on—that few, if any of those other people have, so I guess that the increased difficulty is to be expected. I'm not saying that my stuff is necessarily higher quality than anyone else's, but rather that my criteria are somewhat different and that therefore the process is necessarily also somewhat different.
What is the current availability of the KTR?
The unit should be widely available—through dealers both here in the U.S. and in various other countries—by the time this interview is published. Hopefully by then I will have found time to get some kind of updated Klon website going, which of course will have contact info for the current dealers.
The top of the KTR features some text that's apparently causing controversy with some buyers: “Kindly remember: The ridiculous hype that offends so many is not of my making."
Lots of people got the point that I was trying to make and really enjoy the text, while other people find it off-putting or even insulting. It's a wry observation that I can't be held responsible for the overheated emotions that have been introduced into various Klon debates since the earliest days of the Centaur. I knew that in using that text I'd be stirring things up some, but I thought it would be interesting and fun to see how, in reacting to it, people would self-select into either the “love it" or the “hate it" group.
Photo by West Warren.
What does the future hold for Klon?
I've been thinking about this quite a bit lately. Part of me wants to work on design ideas I have—finish those designs to my satisfaction—and then make the resulting products available. The other side of me wants to either refrain from working on those ideas or work on them, finish them to my satisfaction, and then not put the resulting products out. As you may or may not know, many unscrupulous people have expropriated my hard work on the Centaur and KTR circuits and are selling pedals that incorporate my circuit—and in at least some cases, they're making a lot of money. And apparently there is nothing I can do about this from a legal standpoint.
Quite aside from the money they're making from my work, there's the question of what those pedals sound like. My understanding is that a number of those people are claiming their versions sound “identical" to mine, which—for reasons not only pertaining to the clipping diodes you asked me about—I think is very unlikely. Whatever expertise those various people may have, I'm going to go out on a limb and state my belief that it's not likely to be a good or sufficient substitute for the experience I have with the circuit: I co-designed it, I've hand-built and listened to about 8,000 Centaur units, I spent two years working hard to make sure the KTR would sound the same as the Centaur, and I've put almost 25 years of my life into it. If those other guys' pedals don't sound right, then of course Klon's reputation—and my reputation as someone who cares deeply about the quality of what goes out under the Klon name—will inevitably take a hit.
So my feeling is this: If any new product I come out with will be ripped off immediately after its release, and if unscrupulous people will again be making money off of my work, and if on top of that Klon's reputation and my own personal reputation will be at risk every time someone decides to put out his own version of one of my designs, then where is my incentive to release anything new at all? Over the past few years, I've talked with a number of other pedal designers about this stuff—good people who design their own circuits, and whose circuits have also been ripped off—and we all agree there is now an enormous disincentive for any of us to create and release new products.
From what I understand, a lot of the people posting on various online forums seem to feel that it's a wonderful thing for the pedal consumer to have more choices—how could that be bad? Here's how it could be bad: Maybe talented pedal designers—originators—will simply stop designing pedals and take their talents elsewhere to apply them to the design of other classes of products that can't be ripped off quite so easily.
Top 5 Klon Myths
Gear forums are regularly aglow with all sorts of comments about Klon. Here are the most common misconceptions.
- The Centaur is a slightly tweaked [insert name of extant pedal here] circuit. According to Klon's Bill Finnegan, “it's a much more complex circuit than the typical overdrive/boost circuit. These claims stopped almost immediately after it was reverse-engineered in 2007 and a schematic was posted online."
- Certain Centaurs sound better than others. Finnegan says he's heard this claim about earlier units, later ones, gold ones, and silver ones. “The fact is, under the hood they're all basically the same. In 1995 I made three small changes: I added a resistor to give the circuit some protection against a static charge delivered to its input—a change that has no sonic effect. I also had the circuit board redesigned with a ground plane for better grounding—again, no sonic effect except the potential for a little less hum. And I added a resistor to give the circuit a very small amount of additional low-mid response—I wanted it to have a little more roundness when used with, say, a Strat into a Super Reverb. I made no other changes."
- The KTR doesn't/can't sound as good as the Centaur. Finnegan says this claim arises because the KTR uses surface-mount parts while the Centaur (and most other pedals) use through-hole parts. “For two years my assistant, John Perotti, and I listened to hundreds of different surface-mount parts throughout the circuit," Finnegan explains. “While it wasn't an easy or pleasant process, we both feel—and now a lot of other people feel, as well—that I achieved my design goal: With careful component selection, the KTR sounds the same as the Centaur."
- You have to play really loud for the Centaur or KTR to sound good. “You need to have the output knob high enough that the signal hits the front end of your amp harder than your bypassed signal would," says Finnegan. “In other words, you need to use the unit as an overdrive in the literal sense of the term." The assumption here is that users are pairing the Centaur or KTR with an all-tube amp. “It's always a good thing if your amp is turned up enough to get the harmonic response and distortion that are engendered by tubes clipping and output transformers saturating. This is true whether you're playing through a 4-watt or a 100-watt amp."
- Certain clones sound “exactly the same" as a Klon. Finnegan's contention is that, given several factors—especially the rarity of the Centaur's germanium clipping diodes—it would be extremely difficult to create an identical-sounding overdrive/boost.
[Updated 12/12/21[
- Klon vs. Klone: 5 Affordable Stomps Go Head to Head with a Gold ... ›
- What Does It Even Mean When We Say a Pedal Is "Transparent"? - Premier Guitar ›
- Green Giant: History of the Tube Screamer - Premier Guitar ›
- Klon vs. Klone: 5 Affordable Stomps Go Head to Head with a Gold Original - Premier Guitar ›
- Why I Built This: Atelier Rosenkrantz’s Rachel Rosenkrantz - Premier Guitar ›
- A Beautifully Simple Vibrato Like No Other - Premier Guitar ›
- Spun Loud The Litigator Review - Premier Guitar ›
In line with the MOOER’s recent expansion on the MSC range, the company is excited to announce the new MSC50 Pro, an Alder-bodied electric guitar with gloss finish, available in the new Magic Crystal color.
Featuring a roasted maple neck with a satin finish, a rosewood fingerboard for playing comfort, 22 frets, and a standard C shape, the guitar has been designed with classic guitarists in mind. This is beautifully emphasized with its beautifully resonant tonewoods, all while still being balanced perfectly with style and comfort of use.
The MSC50 Pro features all of the industry-standard features you might expect from such an impressively affordable guitar, such as bolt-on construction, a bone nut, and a dual-action steel truss rod. However, other features make the electric guitar stand out among others at a similar price point, such as its MTN-3LC locking tuning pegs, beautiful Abalone dot inlay, and, of course, its previously mentioned tonewood selection.
In order to capture the MSC50 Pro's balanced tonal profile, MOOER's luthiers have built it with three perfectly balanced pickups: the MSC-II N single coil neck pickup, the similar MSC-II M single coil middle pickup, and, best of all, the MHB-II B bridge humbucker. When these carefully chosen pickups are combined with the guitar's MPW 2-point chrome bridge, guitarists can make the most out of its tonal versatility, all while maximizing tuning stability.
To ensure that the guitar is suitable for a wide range of genres, both softer and higher-gain examples, the MSC50 Pro has a convenient coil split switch built into it, giving users better resonance control. Of course, this is also combined with a classic tone dial, a standard 5-way tone switch, and a volume control dial.
Overall, the MSC50 Pro reminds users of MOOER guitars that the company has never forgotten about its roots in classic-style guitars. Yes, the company is continuing to develop innovative guitar technology in other areas, but this electric guitar also represents a grounded approach, keeping things classic, sleek, and tonally versatile–all at a reasonable price point.
Features:
- Alder Body with a Gloss Finish
- Available in the Magic Crystal color
- Standard C-shaped roasted maple neck with a Satin finish
- Bolt-on construction
- 22-fret rosewood fingerboard
- Abalon dot inlay
- MTN-3LC locking tuners
- Bone nut
- Dual-Action Steel Truss Rod
- 12" radius
- 09-46 strings
- 25.2" scale
- MSC-II N Single Coil neck pickup, an MSC-II M Single Poil middle pickup, and an MHB-II B Humbucker Bridge Pickup
- Chrome guitar strap pin
- Coil Split Switch
- 5-Way Tone Switch
- Volume and tone dials
- MPW 2-Point chrome bridge
The MSC50 Pro will be available from the official distributors and retailers worldwide on 13th May 2025 at an expected retail price of USD419/Euro399/GBP339.
GTRS Announces the W902, The Latest Update to its Wing-series of Intelligent Guitars
This year has marked the return of GTRS’ Intelligent Guitar products, notably with the recent announcement of the SL810 release. Additionally, the company has now announced the upcoming release of the W902, an upgraded version of the original W900 Intelligent Guitar, bringing affordability to the series yet again but without compromising on quality and technical features.
For tonewoods, GTRS has chosen to build the W902 with an Alder body, complete with a delightful Magic Crystal color and High Gloss finish. Attached through bolt-on construction is a 5-piece C-shape neck made from selected roasted flame maple and rosewood, complete with a Satin Natural finish, Rosewood fingerboard, and a White Shell dot inlay. A Dual-Action Steel truss rod runs through the neck, topped with a bone nut, and 24 white copper (0 fret stainless) fanned frets.
While the construction is certainly impressive, the most notable feature of the W902 is the upgraded GTRS Intelligent Processor System, the G151, which even offers upgrades over the SL810's recently announced G150 system. Pre-installed on the system is a staggering 128 effects, along with 10 of both MOOER's in-house MNRS amp and cabinet simulation profiles. Exclusive to the W902, the G151 system even includes 17 guitar simulation effects, allowing guitarists to emulate the tonal resonance of some of their favorite guitars.
To activate and browse through presets within the G151 system, which can be connected via Bluetooth 5.0, guitarists can use the guitar's Super Knob, which lights up in different LED colors depending on which preset is activated. Of course, users are able to get stuck into and edit the effects chains of presets through the GTRS app, enabling them to craft their own favorites through their mobile device. The guitar still functions without the G151 system; the Super Knob just needs to be turned off, and the W902 is usable as a regular electric guitar.
Within the GTRS app, there is even an 80-second looper, 10 metronomes, and 40 drum machine grooves built in, providing users with an all-in-one suite for guitar practice and composition. This is especially the case when combined with the W902's OTG-recording support, enabling on-the-go recording without the need for a hardware recording setup.
No effects and amp simulations would be complete without being complemented by high-quality pickups, which isn’t a problem for the W902 considering the GTRS HM-2N Alnico V neck pickup and GTRS HM-2B Alnico V bridge pickup, both of which resonate beautifully through the guitar's GTRS HL-II bridge.
GTRS always wants to ensure that its customers are set up with everything they need to jam, which is why the W902 comes bundled with a GTRS Deluxe gig bag, three guitar wrenches, a USB 3.0 cable for charging, and a user manual. The guitar even contains a wireless transmitter and an integrated 4000mAh Li-ion battery, providing up to 12 hours of continuous use (9 hours with the transmitter in use), allowing users to enjoy the G151 system through headphones or an amplifier.
Along with all the bells and whistles, the W902 also sports standardized guitar features, such as knobs for volume control and tone, a 3-way pickup switch, and a black GTRS strap pin. However, those who want to experiment further with the guitar’s impressive technology can connect the intelligent system to the GTRS GWF4 wireless footswitch, which is ideal for switching between presets in live scenarios when control through a mobile device isn't practical. Overall, the W902 is yet another example of GTRS’ commitment to continually improve its Intelligent Guitar series.
GTRS W902 Guitar construction features:
- Alder Body
- Magic Crystal Color
- High Gloss Finish
- 5-Piece Selected Roasted Flame Maple and Rosewood Neck with Satin Natural Finish (C-Shape)
- Bolt-on construction
- Rosewood fingerboard
- 24 white copper (0 fret stainless) fanned frets
- White Shell dot inlay
- 42mm Bone Nut
- 12" radius
- 25-1/2" scale
- 09-46 strings
- Dual Action Steel truss rod
- GTRS HL-II bridge
- GTRS HM-2N Alnico V neck pickup
- GTRS HM-2B Alnico V bridge pickup
- Black GTRS strap pin
- Built-in wireless transmitter
- Super Knob, Volume Control Knob, and Tone Knob
- 3-way tone-selection switch
- GLB-P1 Li-ion Battery (4000mAh, up to 12 hours of continuous use, 9 hours with the wireless transmitter in use)
- USB port for charging and OTG recording
- GTRS Deluxe gig bag
- 3 guitar wrenches
- USB 3.0 Type A to C cable
GTRS G151 Intelligent Guitar System features:
- GTRS G151 Intelligent Processing System (and GTRS App)
- 128 effects
- 10 MNRS amp (GNR) and cabinet (GIR) simulation models
- 17 guitar simulations
- 80-second looper
- 40 drum machine grooves
- 10 metronomes
- Bluetooth 5.0 connectivity
- GTRS GWF4 wireless footswitch support (sold separately)
The GTRS W902 will be available from the official distributors and retailers worldwide on 13h May 2025.
MOOER Expands Its Popular MSC Guitar Line with the MSC30 Pro and MSC31 Pro
MOOER has never shied away from innovation when it comes to its guitars. However, with the recently announced release of the MSC30 Pro and MSC31, the company reminds us that, sometimes, true innovation lies in mastering and enhancing a proven classic. With this philosophy, MOOER introduces two new exciting additions to their beloved MSC series of electric guitars.
Both the MSC30 Pro and MSC31 Pro continue MOOER’s philosophy of creating affordable guitars, but without sacrificing quality or performance, thanks to the poplar bodies and flame maple tops. Some guitarists will be drawn to the bright tones of the MSC30 Pro’s maple fingerboard, whereas others will prefer the warmer resonance of the MSC31 Pro’s rosewood alternative.
Each guitar features sturdy bolt-on neck construction, dual-action steel truss rods, bone nuts, and MTN-1 chrome tuning pegs (with the BK upgrade being reserved for the MSC31 Pro), ensuring tuning stability and comfort at all times.At the heart of both models are MOOER’s versatile MSC pickups, comprising the MSC-1N single-coil neck pickup, the MSC-1M single-coil middle pickup, and the powerful MHB-1B dual-coil humbucker at the bridge. Further complemented by a versatile 5-way pickup selector and exclusive coil split switch, players can effortlessly switch between a wide palette of tones, such as pristine cleans ideal for jazz or blues, or high-gain tones for heavier genres.
Tremolo support is also provided through both the guitar's bridges, with the MSC30 Pro featuring an MTB-1 2 Point Tremolo bridge, and the MSC31 Pro boasting an exclusive black MTB-1 BK 2 Point Tremolo bridge. Both bridges guarantee guitarists the ability to use tremolo bars in their guitar performances, without compromising the integrity of tuning stability.
Both guitars come with a selection of vivid new colors, complementing the guitar’s hardware with undeniable visual appeal. The MSC30 Pro is available in the classic finishes of Sunset Red, Lake Blue, Lemon Green, and Rose Purple. Meanwhile, the MSC31 Pro boasts its own selection of glossy finishes: Grey Burst, Blue Burst, Green Burst, and Purple Burst.
Overall, the MSC30 Pro and MSC31 Pro solidify MOOER’s commitment to combining quality craftsmanship, affordability, and versatility, giving guitarists of all levels the chance to own instruments that genuinely inspire.
Features
MSC30 Pro:
- Classic S-style design
- Poplar body with flame maple top
- Maple fingerboard
- Maple neck with satin finish
- Bolt-on neck construction
- 22 nickel silver frets, Abalone dotted inlay
- Coil split switch and versatile 5-way pickup selector
- MSC-1N/M single-coil pickups and MHB-1B humbucker
- 25.5" scale
- MTN-1 Chrome tuning pegs
- Available in gloss-finished Sunset Red, Lake Blue, Lemon Green, and Rose Purple
- Volume and tone dial
- Chrome strap pin
MSC31 Pro:
- Classic S-style design
- Poplar body with flame maple top
- Rosewood fingerboard
- Maple neck with satin finish
- Bolt-on neck construction
- 22 nickel silver frets, White Shell dotted inlay
- Coil split switch and versatile 5-way pickup selector
- MSC-1N/M single-coil pickups and MHB-1B humbucker
- 25.5" scale
- MTN-1 BK tuning pegs
- Available in gloss-finished Grey Burst, Blue Burst, Green Burst, and Purple Burst
- Volume and tone dial
- Chrome strap pin
The MSC30 Pro and MSC31 Pro will both be available from the official distributors and retailers worldwide on 2nd April 2025.
MOOER Gives Bassists What They Want with the New MBJ410 and MBJ420 Electric Bass Guitar Models
For 15 years, MOOER has built a critically acclaimed name for itself thanks to its cutting-edge electric guitars, pedals, and accessories. While the company is no stranger to building electric bass guitars, this has not been its focus for some time, hence why so many bassists are excitedly anticipating the release of the MBJ410 and MBJ420 electric bass guitars.
Both the bass guitars sport glossy Poplar bodies, keeping the price point affordable but without limiting their tonal resonance and versatility, whereas the MBJ420 holds the additional bonus of being built with a Poplar Burl top. Complete with roasted maple C-shaped necks (also accented with a gloss finish) as well as Roasted Maple fingerboards and White Shell dot inlays, the necks are designed to offer as much comfort as possible–a high priority for bass guitarists.
A 34" fret scale further enhances practicality for bassists, as does the neck's 12" radius. Strings are available in .045, .065, .080, and .100 gauges, providing something for any type of bass style - whether slapping, plucking, or picking techniques are preferred.Thanks to the industry-standard components of a dual-action steel truss rod and bone nut, the tuning and resonant stability of both the MBJ410 and MBJ420 models are also of a high standard. However, this is accentuated further by the guitars' strong and reliable BTN-1 tuning pegs, essential for heavier-gauge bass strings.
The tonewoods and structural integrity of the MBJ-series electric bass guitars wouldn't be complete without the accompaniment of the guitar’s two single-coil JB-style pickups. Combined with the MOOER BSC-2 bridge, both bass guitars have been carefully designed to amplify bass resonances excellently, complemented even further by their simple but effective tone dials. Two volume controls are also built in, ensuring that bassists can customize their sonic output to have the perfect tonal blend.
In terms of standout features, the main difference between the two bass guitars is the MBJ420's added poplar burl top, but most notably, the color selections. For the MBJ410, the bass guitar is available in Gunmetal Gray, Metal Green, and Metal Blue, perfectly suiting the stages of higher-gain performances. In contrast, the aesthetics of the MBJ420 are more classic, purchasable in Red Burst, Blue Burst, and Tobacco Burst. Finally, both guitars are topped with a chrome strap pin, enabling stylish and energetic live performances.
Overall, bassists will no doubt be excited to see MOOER return to electric bass guitars with the MBJ410 and 420 models. Of course, electric guitars will remain the focus for the company, but the release of these two new products is a reminder of just how accommodating MOOER is for its wide audience of musicians.
Features
- Electric bass guitar built with gloss-finished Poplar body (MBJ420 also features a Poplar Burl Top)
- Roasted maple C-shaped neck with a gloss finish
- Roasted maple fingerboard
- White Shell dot inlay
- 12” neck radius
- MOOER BSC-2 bridge
- VBJ-1 and VBJ-2 Single Coil pickups
- MOOER BTN-1 tuning pegs
- Bolt-on construction
- Bone nut
- Dual-action steel truss rod
- Pre-installed strings available in .045, .065, .080, and .100 gauges
- 21 frets
- 34"fret scale
- Colors available in Gunmetal Gray, Metal Green, and Metal Blue (MBJ410), and Red Burst, Blue Burst, and Tobacco Burst (MBJ420)
- Chrome strap pin
- 2 x volume control dials
- 1 x Tone dial
The MBJ410 and MBJ420 will both be available from the official distributors and retailers worldwide on 29th April 2025 at an expected retail price of USD319/Euro299/GBP249(MBJ410), USD399/Euro379/GBP319(MBJ420).
The Oceans Abyss expands on Electro-Harmonix’s highly acclaimed reverb technology to deliver a truly immersive effects workstation. The pedal is centered around dual reverb engines that are independently programmable with full-stereo algorithms including Hall, Spring, Shimmer and more. Place these reverbs into a customizable signal path with additional FX blocks like Delay, Chorus, Tremolo, or Bit Crusher for a completely unique soundscape building experience.
Electro-Harmonix has paved the way for powerful, accessible reverbs since the release of the original Holy Grail and now we’ve pushed the envelope deeper with the fully-equipped Oceans Abyss. Featuring a customizable signal path with up to 8 effects blocks, the Oceans Abyss can be configured as individual reverb, modulation, EQ, delay, bit crusher, saturation or volume effects, or as countless combinations for incredibly creative effect shaping. From a simple Spring reverb to a lush stereo field featuring stereo hall and shimmer reverbs, chorus, delay, overdrive, and tremolo, you can go from surf to shoegaze instantly, without breaking a sweat.
Deep parameter editing is accessible via the high-visibility OLED display with multiple graphical views and easy-to-read designs. Expression/CV control over nearly every parameter gives artful control of your effects and dynamics. Fully-stereo I/O plus an FX Loop allows for use with any instrument, recording set up, or live rig. 128 programmable presets via onboard footswitching or MIDI ensure perfect recall in all performance situations. MIDI IN/OUT ports with MIDI IN support of PC, CC, and Tempo Clock expand the already immense talents of the Oceans Abyss. Connect with UBS-C to Windows or Mac for effects editing, preset management, and more with the free EHXport™ app (coming soon).
- Two Stereo Reverbs available at once, each fully pannable in the stereo field
- 10 reverb types to choose from: Room, Hall, Spring, Plate, Reverse, Dynamic, Auto-Infinite, Shimmer, Polyphonic, Resonant
- Additional FX blocks: Delay (Digital, Analog and Tape emulations), Tremolo, Chorus, Flanger, Phaser, Graphic EQ, Saturation, Bit Crusher, External FX Loop, Volume
- Create custom signal path routing with up to 8 effects blocks. Two blocks may be re-verb, the rest may be any of the additional FX blocks.
- Infinite reverb sustain with the press of a footswitch
- Stereo Audio I/O
- Stereo FX Loop routing on TRS Jacks
- Dual action footswitches allow for momentary or latching use
- Easily enable or disable tails
- 128 fully customizable presets
- All controls can be saved to presets
- Dive deep into global and preset settings to set up Oceans Abyss for your specific needs
- Illuminated slide pots and buttons
- High-visibility OLED graphical display
- Multiple graphical views: Signal Path, Performance, Settings, Physical, Explorer
- Easy-to-navigate menu system
- Ergonomic NavCoder knob allows rotary and directional navigation through menus
- EXPRESSION / CV input to control nearly any parameter in any FX block
- Footswitch input allows for adding up to three external footswitches, each assigna-ble to a number of functions
- MIDI In and Out. MIDI IN supports PC, CC (over nearly every available parameter), and Tempo Clock
- USB-C port to connect to Windows or Mac and interface with EHXport™ app (coming soon)
- 96kHz / 24-bit sample rate conversion
- Supplied with 9.6VDC / 500mA power supply
Axe-wielders Jake Cinninger and Brendan Bayliss take us through their current gear garages.
It’s been just over 10 years since we had legendary South Bend, Indiana, jam band Umphrey’s McGee on Rig Rundown, so when we saw that they were coming to play at Nashville’s Ryman Auditorium in early April, we figured it was time to reconnect.
Guitarists Jake Cinninger and Brendan Bayliss showed PG’s John Bohlinger what pieces of kit they’re digging these days, and how they orchestrate their incredibly broad range of sounds.
Brought to you by D’Addario.
Simply Z Best
Here’s an up-close look at Cinninger’s No. 1, a G&L Comanche. The Z-coil pickups do away with typical single-coil 60-cycle hum issues at high-gain settings. It’s an all-purpose workhorse.
Cinninger replaced the stock trem bar with a Jake Blade, a custom-made replacement patented by Mark Benjamin of RoughGauge LLC. Compared to a regular trem bar, it’s out of the way and allows for more expressive playing.
For strings, Cinninger uses D’Addario .10s, and he swears by his beveled-edge Telefunken 2 mm picks.
Special S
Cinninger says only 50 of these G&L S-styles were made, with remarkable pieces of wood and specially designed pickups. This one cuts closer to a classic, throaty Stratocaster sound, and if a venue has quiet, clean power that won’t present excessive noise issues, it’s more likely to be called into action.
Two by Two
Cinninger’s signal runs to one amp at a time. The Schroeder head, which is used for cleans, was built with military-spec durability by Tim Schroeder in Chicago and is one of 10. Cinninger says it’s got some Dumble qualities, with its clarity, power, consistency, and speed to the speaker, and it connects to a Schroeder cabinet and custom speaker.
The Oldfield Marquis 100-JC, built by Paul Gussler in Charlotte, North Carolina, is the Marshall-flavored side of Cinninger’s rig. It handles dirty signals and is connected to classic Electro-Voice drivers.
Jake Cinninger’s Pedalboard
Cinninger’s board, which he made with his dad, is 25 years old, and it’s constantly changing. His always-on boxes include a Banzai Cold Fusion Overdrive, Fuchs Royal Plush Compressor, and Mesa Boogie Five-Band Graphic EQ, plus a Steel Guitar Black Box tube buffer that adds some “air” in the high end.
On top of those, there’s a Boss TU-3, MXR Smart Gate, Radial Tonebone Hot British, MXR Distortion III, Sarno Earth Drive, TC Electronic Flashback, Boss PS-5, Source Audio Soundblox 2 Multiwave Distortion, Malekko Fuzz, Guyatone MD2, Boss PH-3, Morley Bad Horsie, BBE Mind Bender, and a custom “FuzzBucket” fuzz made by a friend.
Utility units include a Lily P4D, Radial BigShot ABY, and Ebtech Hum Eliminator, plus a 9-channel effects switching system.
Sorry, Mark
Meet Miss Lucy. This is a PRS Mark Tremonti Signature, albeit without Tremonti’s name on the headstock, and tricked out with the Jake Blade. This one runs a bit hotter than Brendan Bayliss’ other PRS guitars, and his tech changes the strings on it—D’Addario XL .010s—every day. Like Cinninger, he digs the Telefunken 2 mm picks.
Also in the stable are another PRS single-cutaway and a double-cut PRS McCarty.
Doubles of the Oldfield
Bayliss runs both a Mesa Boogie Lonestar head and a Gussler-built Oldfield head (which sounds similar to his Lonestar) at the same time. The Mesa runs to a cab with Celestion 12″ speakers.
Brendan Bayliss’ Board
Bayliss’ board also features the Steel Guitar Black Box, a Lily P4D, Radial BigShot ABY, a Boss TU-3, and a Morley 20/20 Bad Horsie wah.
Aside from those, there’s a Keeley Compressor, MXR Custom Badass Modified O.D., Cusack Screamer, MXR Timmy, Cusack Tap-A-Whirl, Audio Blend Edge EQ, Boss OC-5, Boss CE-5, MXR Phase 95, Eventide H9, Stigtronics Delay, and Boss DD-20.
Guitarist William Tyler, a restless sonic explorer: “I would get bored staying in the same place.”
The expansive instrumental guitarist/composer pushes himself out of his comfort zone, beyond the boundaries of his neo-Americana wheelhouse on Time Indefinite.
Mastering an instrument and an artistic style—and then being recognized and rewarded for it—is a daunting enough accomplishment that one might be forgiven for feeling that, once reached, it’s the be-all to end-all. Guitarist William Tyler, for all the praise and opportunity that have come his way over the past decade and a half, isn’t content to plow the same furrow. With his evolutionary new album, Time Indefinite, this son of the South is pushing further afield, not completely forgoing his virtuosic neo-Americana lyricism but incorporating it into static-friendly, otherworldly studio experimentation.
The disorienting opener of Time Indefinite, “Cabin Six,” begins with a loop of hovering blare that, lasting nearly a minute, might lead listeners to think something is amiss with their turntable stylus; this gradually dissipates into an eddy of railroad-like whine from which a chiming 6-string hook emerges only to finally sink into a murky, detuned drone. The simple, lovely “Anima Motel” and almost naïve “Concern” are eminently approachable, and “Howling at the Second Moon,” with its alternate, Joni Mitchell-inspired tuning, feels like something that could have appeared on one of Tyler’s previous albums (even if it was recorded on his iPhone then texturized via a bump to a cassette recorder and dosed with added effects). But the distressed sonic sculptures of “The Hardest Land to Harvest” and “Electric Lake” or the sampled, distorted church choir laced through “Star of Hope” have a ghostly resonance unlike anything the guitarist has done before.
SoundStream
“I think it’s important for artists to push themselves into new ways of working,” Tyler says. “Most of my favorites, artists I follow over the long trajectory of their careers, have done that, whether it’s in music, film, visual art, novels. Of course, some people have a method or style that they stick to, and it serves them. And I wouldn’t want to put anything out into the world that I wouldn’t myself, as a consumer, enjoy spending time with and taking seriously. That said, I would get bored staying in the same place. The new record is about making something that was a little less chained to certain kinds of guitar music, where I felt like I might be running up against my creative limitations or enthusiasms in that area. I wanted to reinvent myself for myself, to explore fresh possibilities, even with the guitar as my primary tool.”
Tyler, whose parents were hitmaking Nashville songwriters, made his name early on as a young guitar phenom playing in such alternative-minded, country-influenced bands as Lambchop and Silver Jews, before appearing on the fourth volume of the influential Tompkins Square “Imaginational Anthem” series of new-era American Primitive guitar and then making his full-length debut as a solo artist with the 2010 album Behold the Spirit. As a player and composer, he was recognized for subsuming the early influence of John Fahey and the Takoma style into something vibrantly his own.
Tyler keeps his tools simple and his ears open.
Photo by Angelina Castillo
William Tyler’s Gear
Guitars
- Mid-1950s Martin D-18
- 1974 Gibson SG
Pedals
- Hologram Electronics Microcosm
- Strymon El Capistan
- Line 6 DL4 Mark II
Once Tyler signed to the stalwart indie-rock label Merge, the guitarist released a string of warmly received electro-acoustic albums: Impossible Truth (2013), Deseret Canyon (2015) and Modern Country (2016). There was also a marvel of a solo performance at Nashville’s Third Man Records released as an LP in the “Live at Third Man” series. A few years later came the album Goes West, its title alluding to a pre-pandemic move to Los Angeles, and its arrangements flecked with atmospheric swirls and sunny, almost pop-like touches. Tyler also created an aptly rustic score for First Cow, director Kelly Reichardt’s 2019 art house Western, and the guitarist capped his Merge run in 2023 with Secret Stratosphere, a live album of soaring full-band versions of numbers from his back catalog, credited to William Tyler’s Impossible Truth.
“I wanted to reinvent myself for myself, to explore fresh possibilities, even with the guitar as my primary tool.”
Tyler has released covers of such disparate artists as Alex Chilton, Michael Chapman, Fleetwood Mac, Yo La Tengo and Neu!/Harmonia’s Michael Rother, not to mention classical composers Handel and Dvorák. The broad listening palette suggested by these choices always pointed toward a more intrepid path. But the album that most presaged the spirit of Time Indefinite is New Vanitas, a small masterpiece of pandemic creation that found him threading beautiful, involved guitar melodies through hypnagogic soundscapes, often haunted by lo-fi snatches of radio broadcasts and sotto-voce dialogue, as on the evocatively titled “Slow Night’s Static.” New Vanitas even includes a woozy track called “Time Indefinite,” the foreshadowing title a favorite that he borrowed from a film by documentarian Ross McElwee.
On Time Indefinite, Tyler says, “I was drawn to more ambient music, including by guitarists like Christian Fennesz and Norman Westberg, but also groups like Stars of the Lid and Boards of Canada.”
Another signpost on Tyler’s new road was a collaboration with Four Tet’s Kieran Hebden that yielded the folktronica single “Darkness, Darkness.” Then last year brought the standalone track “Flight Final,” Tyler’s first release for the artist-led imprint Psychic Hotline, and a slice of musique concrète that brings to mind Brian Eno’s association with German “kosmische” pioneers Harmonia and Cluster. That recording, the first fruit of an association with collaborator and co-producer Jake Davis, set the stage for their work together on Time Indefinite. Most of the pieces on this album, whether blown-out lullabies or spectral hymns or folk-art abstractions, feel like memories refracted in a dream diary.
“The process of working on this album helped me get better at tempo, just feeling more comfortable playing slower.”
“The new album started out as a series of experiments, without necessarily thinking that they were going to make for a whole record—though, eventually, Jake and I heard a thematic coherence to what we were coming up with,” Tyler explains. “It took a long while to come together, but the roots of the music are in the Covid lockdown. The emotional landscape of that time changed the things I was listening to as well as the music that was coming out of me. I was drawn to more ambient music, including by guitarists like Christian Fennesz and Norman Westberg, but also groups like Stars of the Lid and Boards of Canada. I had gone back to Nashville and was dealing with a problematic mental state. Among other issues, I can tend to approach things too fast, spiritually, emotionally, and physically. Beyond using different recording techniques and learning new ways of creating a piece of music, the process of working on this album helped me get better at tempo, just feeling more comfortable playing slower.”
The guitars Tyler used in the studio for Time Indefinite were his “family heirloom” Martin D-18 and a beloved Gibson SG, both of which are his main live instruments. For effects pedals, he favored a Hologram Electronics Microcosm (“for low-pass filter looping and really weird granular stuff”) and a Strymon El Capistan (“for delays kind of like the old Electro-Harmonix Memory Man”), though Davis also did a lot of processing with an array of his own. One serendipitous piece of gear was a 1959 Webcor Regent reel-to-reel machine deck that Tyler liberated, still new in the box, while helping to clear out his grandfather’s storage space in Mississippi. Davis was inspired to make old-school tape loops with it, including that startling sound that opens the album. Tyler would play arrhythmic, asymmetrical parts that Davis would record and chop up for the loops.
Tyler at this year’s Big Ears Festival with Jake Davis and Cecilia Stair.
Photo by Ross Bustin
Tyler’s recent spate of collaborations, from Davis and Four Tet to pedal-steel guitarist Luke Schneider, “has kept me on my toes, challenged me and recharged me,” he says. “The insularity of being a solo instrumentalist and writing everything by yourself can be freeing at first. And it can be motivating, as when I first started learning how to play fingerstyle guitar, with all the practicing. But I don’t like the isolation of it now. These days, I prefer working with other people. It pushes you into other genres, those different modes of communication.”
Another recent colleague, Marisa Anderson, has credited Tyler for his open, venturesome spirit as a studio partner, with his default attitude of “yes” when they were making their absorbing duo album, Lost Futures. “That was something I really enjoyed about playing with William—he was up for everything,” she said. “I was like, ‘There’s the diving board,’ and he’d say, ‘Let’s go.’”
“These days, I prefer working with other people. It pushes you into other genres, those different modes of communication.”
Tyler is quick to credit artists and albums that have inspired him. Along with the aforementioned players, he namechecks a vast range of others, from Jimmy Page to Jeff Parker, Bill Frisell to Fred Frith, Bruce Langhorne to Nels Cline, William Ackerman to Sandy Bull. Tyler muses about how some of his Nashville session heroes should “have gotten weirder…. I wish Chet Atkins had dropped acid, listened to a Sonny Sharrock LP, and made his own noise record, you know?” Regarding his touchstones for sonic left turns, he points to Wilco’s Yankee Hotel Foxtrot, as well as Talk Talk’s emotive, avant-minded swansongs Spirit of Eden and Laughingstock.
“Those two Talk Talk albums are beyond masterpieces, with some great guitar playing,” Tyler says. “They were in essence made by an artist, Mark Hollis, who did not care about being commercial anymore and certainly not about being able to replicate the stuff live. When Jake and I were recording ‘Howling at the Second Moon,’ that sort of attitude was a reference point, kind of like, ‘Well, instead of trying to get away from the lo-fi weirdness of my original iPhone demo, why don’t we lean into it?’”
Ever thoughtful and candid in conversation, Tyler has been exceptionally transparent about coping with personal loss and midlife crises, as well as going to rehab for the over-indulgence of alcohol. Knowing that, one can hear grief and anxiety in the whorls of Time Indefinite, with the passages of guileless 6-string representing a nostalgia for less complicated times. “It’s a mental landscape record for sure,” he says. “For fans of my previous albums, it might not hit the same way, I realize. But I hope this record says to people that it’s all right to take chances with how you express yourself, with how naked and raw that can be. It has a purposeful arc and is meant to prompt things that aren’t super fashionable in today’s ephemeral, constant-content culture, like deep listening, emotional ambiguity, self-reflection, you know?”YouTube It
This three-song set from last year showcases the expansive cosmic country sound of Tyler and his Impossible Truth band, which includes a Kraftwerk cover.