
The reclusive pedal builder discusses the origins of his famed Centaur overdrive, the more affordable new KTR design, and how one pedal can inspire so much adoration and disdain.
If you've spent any amount of time on guitar-gear forums, you know they can often devolve into pretty abrasive battles of opinion. Even when a thread starts out with the best of intentions, it's not uncommon for it to morph into the online equivalent of a mythical Hydra. Forum administrators attempt to clean things up and lock out the more abusive commenters, but once they cut off one of the creature's heads, two more appear.
Of all the forum topics that can inspire such heated debate, few inspire more passion, awe, and vitriol than a guitar pedal named after a different sort of mythological creature. Launched in 1994 at the front end of the modern-day boutique-pedal boom, the Klon Centaur overdrive was immediately met with critical acclaim. So much so that it's ironic how much the pedal named after the half-human, half-horse creatures from Greek legend has since developed such a complex mythology of its own. And the fact that this seemingly mundane, 3-knob stompbox is used by such high-profile players as Jeff Beck, John Mayer, Joe Perry, Nels Cline, and Matt Schofield only compounds matters. Never mind the fact that the majority of the circuit comes encased in epoxy.
We recently spoke to Klon's Bill Finnegan about the origins of the Centaur, his new KTR design—which made a (naturally) limited debut in October of 2012—and how an overdrive pedal can fetch more than $1,000 on the used market and inspire such emotionally charged reactions.
Birth of a Centaur
In the 1980s, Bill Finnegan played in a band where he plugged his Telecaster straight into a Twin Reverb turned up as loud as the soundman would permit. In bigger Boston-area clubs, the Twin's volume would be at 6 or sometimes even 7, but in smaller places Finnegan could usually turn it up to only 3 1/2 or 4. The latter still sounded good, but not as harmonically rich as when the amp was working harder. Although it didn't occur to him at the time, a pedal that would give him the sound of a cranked amp is exactly what he needed.
Finnegan recalls that, in 1990, guitarists began chasing after out-of-production Ibanez Tube Screamers in droves. He'd heard about a guy who was selling two TS9s, and—hoping one of the little green pedals would help make his Twin sound like it was at 6 when it was only at 4—he went to check them out. It immediately became clear that Tube Screamers were not for him.
Finnegan built Centaurs—around 8,000 in total—by hand, on a cheap folding card table in a succession of small apartments for 15 years.
“[The TS9] compressed the transient response of the original signal a lot, had a midrange character I didn't like, and subtracted a noticeable amount of bass response from the signal as well," he explains. The same seller also had a TS808 that he wasn't selling. And, though Finnegan thought it sounded a little better than the TS9s, he still felt it had the aforementioned shortcomings. What he really wanted was a big, open sound, with a hint of tube clipping—a sound that would make you unaware a pedal was involved.
That's when Finnegan starting looking into creating a new design that would meet those criteria. He recruited a friend who'd just graduated from MIT with an electrical engineering degree. Though both had day jobs, for the next couple of years they got together once a week and tried to push the ball down the field. Within the first year, they'd developed prototypes that were much closer to what Finnegan wanted than a Tube Screamer, and various guitarists in the Boston area encouraged them to go into production so they could buy their own. But Finnegan felt the circuit could still be improved, so he and his partner kept working.
Eventually, the MIT friend bought a house in the suburbs and the distance made it harder to work together. Finnegan later partnered with the late Fred Fenning (who tragically passed away in a plane crash in the mid '90s)—another MIT grad whom Finnegan says was brilliant and very determined. Although Fenning had never designed an audio circuit and had no real interest in music, he was exceptionally good at finding ways to give the circuit what Finnegan thought it needed at any given time. Finnegan says Fenning deserves a lot of credit for the circuit in both the Centaur and its successor, the KTR.
Photo by Sarah Pollman
The entire design process took four and a half years, and when the pedal debuted at the end of '94 Finnegan was soon very busy trying to keep up with the demand—building, testing, and shipping the pedals as a single-man outfit.
Evolution of the Legend
From that point on, demand for Centaur pedals grew. Finnegan says he typically worked 55–60 hours per week in effort to keep turnaround times as short as possible, though he was hindered by the fact that the circuit was very labor intensive and time consuming. He also says it was more expensive to build than most other pedals due to the fact that everything from its cast enclosure to its knobs, pots, and sheet-metal bottom were custom crafted. Finnegan estimates the aggregate cost of a Centaur as seven to eight times that of a pedal built with off-the-shelf parts.
“For the last seven years or so of Centaur production, the retail price was $329," says Finnegan, “and to be honest, my profit margin was not very sensible—no real business person would have considered, for more than a moment, doing what I was doing for the return I was receiving. Also, given that I live in Boston, it was impossible for me to hire people and expand: Real estate here is in short supply and very expensive, so there was no possibility of my renting commercial space to set up an actual shop."
Finnegan built Centaurs—around 8,000 in total—by hand, on a cheap folding card table in a succession of small apartments for 15 years. In addition to the modest returns from his efforts, Finnegan says he felt immense stress as he tried to oblige those who wanted a Centaur but didn't want to pay the inflated price used specimens were fetching because of the 12- to 14-week turnaround time for a new one. It gradually became clear to Finnegan that the situation was unsustainable.
“These two photos show my testing jig for Centaur boards, with one of my experimental boards on it," Bill Finnegan shares. “The experimental boards have sockets for every component in the circuit, which enables me to listen to any particular component and then swap it out for a substitute while keep everything else the same. This experimental board is the one I used for developing the KTR. Unlike the Centaur which had through-hole components with leads, I wanted to use surface-mount components for the KTR, which meant that my assistant, John Perotti, and I had to spend an enormous amount of time soldering through-hole leads onto hundreds of very small surface-mount components so that we could evaluate them and choose the ones that would make the KTR sound the same as the Centaur did."
Photo by Nolan Yee.
“I was going to have to kill it before it could kill me," Finnegan recalls. In 2008, he began working on a ground-up redesign that had to meet the following criteria: It had to be straightforward to build, so that any good contract manufacturing firm would be able to do the job easily and well. It had to be rugged and reliable. It had to be a design with no hookup wires whatsoever, and with a modular footswitch assembly so that faulty footswitches could be replaced in a few minutes. It had to be considerably smaller than the Centaur. Except for the all-important clipping diodes, it had to have surface-mount components, which take up less space on a board than traditional through-hole components. Finnegan also wanted to prove—to himself and to those who said it couldn't be done—that, with careful component selection and smart board layout, he could design a successor that would sound exactly the same as the Centaur.
“This turned out to be quite a challenge," Finnegan says. “My assistant, John Perotti, and I spent almost two years listening to different surface-mount capacitors in various places in the circuit before I felt this had been achieved." Lastly, he wanted the new unit to be visually unique—a tall order, given that the unit would be housed in a standard enclosure.
I don't have any overall preference for single-coil guitars or humbucker guitars myself. I like pretty much everything under the sun in the way of electric guitars, and over the years I've owned a bunch of very different ones.
The one new feature Finnegan wanted to incorporate was a switch that enabled the player to choose the buffered output of the original Centaur or a true-bypass output. “Without the buffer there is a very noticeable degradation of the signal due to the capacitance inherent in guitar cables," says Finnegan, “but some people prefer it, so I wanted to provide that option in the new unit." He quickly adds, “My good friend Paul Cochrane—of Tim and Timmy [pedals] fame—was the guy who designed the switching circuitry, so a tip of the hat to Paul."
It took a long, long time to finish the KTR. And though Finnegan says it was much more difficult than he expected, he feels it has achieved all of his design objectives. “It sounds the same as the Centaur, takes up considerably less space on a pedalboard, is less expensive, and it's distinctive aesthetically—it's got the Klon thing going on." He laughs, “Whatever the Klon thing is."
You obviously have high expectations from your designs, though you're also perplexed by the reactions it inspires. What do you want people to see in Klon?
What I want people to expect from me and from Klon are designs that are exceptional in the literal sense of the term—designs that are conceptually sound and well executed. Designs that are unique and not to be expected from any other designer, no matter how talented.
When you were designing the Centaur, did you begin with any assumptions about players who'd be interested in it?
I was working from the assumption that there were a lot of guitar players with really good guitars and really good amps who were looking for an overdrive pedal that—whether it was adding dirt or not itself—wouldn't mess up what they already had and liked. Given the popularity of the Centaur and now the KTR, I would say that this has been borne out.
In your opinion, do the pedals work better with single-coils or humbuckers?
Neither. I don't have any overall preference for single-coil guitars or humbucker guitars myself. I like pretty much everything under the sun in the way of electric guitars, and over the years I've owned a bunch of very different ones. Each of them has its own particular thing going on, and when I was working on the design of the circuit I was always thinking about how it could be more effective in preserving and accentuating the essence of whatever instrument it was receiving the signal of.
What can you tell us about Centaur units that occasionally turn up on eBay with the claim that they are “new, with full warranty"—are they fakes?
I have a very close friend who is a single mom and whose job doesn't pay all that well. Every now and then she needs a little help, financially. I'm aware of what the used units are selling for, so at some point after I discontinued the Centaur it occurred to me that—if and when she needed me to—I could build a Centaur and give it to her to sell on eBay and use the proceeds to keep going. This has worked really nicely, and I'll continue to do it for as long as my old Centaur parts last. Since I discontinued the Centaur, a lot of people have asked me whether I'd consider building one for them—sometimes offering me pretty substantial amounts of money—but I'm not going to do that. The only Centaurs I build anymore are the ones I build for her, and I don't make or collect a single cent from them.
Klon builder Bill Finnegan wanted to include this text—which refers to the dialogue surrounding his famed Centaur design—on the casing of his new KTR pedal. “It's a wry observation that I can't be held responsible for the overheated emotions that have been introduced into various Klon debates since the earliest days of the Centaur," he says. “I knew that in using that text I'd be stirring things up some, but I thought it would be interesting and fun to see how, in reacting to it, people would self-select into either the 'love it' or the 'hate it' group."
Photo by Nolan Yee.
Do you think Centaurs will retain their high value now that the KTR is available?
Yes, in general I think they will. They're collectible and—with the one small exception I just mentioned—no more will be built, unless I'm very mistaken. For almost everyone, the KTR is a much more sensible option now: It sounds the same, it's much smaller, it's way the hell less expensive—$269 retail—and you don't have to worry about losing something that's worth $1,000 or $1,500 or $2,000 if it's stolen. On the other hand, the Centaur has something of its own that people really like and are willing to pay serious money for. The design has achieved a certain status—I would use the analogy of old, custom-colored Marshalls. I have two small-box, 50-watt Marshall Lead heads—model 1987s: One is a black-Tolex, aluminum-panel head from 1970, and the other is a red-Tolex, plexi-panel head from 1969. They have the same circuitry and sound almost identical, but of course the red one is worth way more than the black one. I like cool, distinctive things as much as the next guy, so I'm not in a position to criticize someone for being willing to pay more than I myself would, or more than most people would, if they want it that much.
What are the demographics of the typical Klon user?
It seems to be more or less everyone. Baby-boomer guys who are still only interested in the music they grew up with, but also a lot of younger, indie-rock people, and also a number of musicians whose work is more experimental and can't be easily categorized.
What can you tell us about the germanium diode you like so much in your circuits?
In 1993 and '94, when it was clear that Fred and I were getting close to producing what I thought was the full measure of what our circuit was capable of, I started buying quantities of every diode I thought might be at all suitable for the head-to-toe pair that clips the signal, except for when the circuit is in clean-boost mode. This was pre-internet, so I was going to the public library, looking up distributors in the Thomas Register, and then calling those distributors to find out what they had—email was still in the future then! I started out ordering both germanium and silicon diodes, but pretty quickly I began concentrating on the germaniums. Usually, though not always, they sounded more natural to me than the silicon ones did. After months and months of listening, I felt a particular new-old-stock germanium diode sounded best in the circuit, so I thought I should buy as many of those as I could afford. Eventually, I found a distributor that had a significant quantity of them. They were stocking them for a huge OEM, who—without any warning, I gather—stopped using that part. I bought them all at a good price. The distributor was thrilled to be able to sell them and not have to eat them.
Does the KTR have the same diodes?
Yes, the KTR has the exact same NOS diodes as all Centaurs did.
Since I discontinued the Centaur, a lot of people have asked me whether I'd consider building one for them—sometimes offering me pretty substantial amounts of money—but I'm not going to do that.
What is it you like about the sound of that diode when it clips?
It's a little more complicated than that, because the diode clipping happens on top of some op-amp clipping in the main gain stage. So it's op-amp clipping, then diode clipping. But to answer your question, this particular diode in the head-to-toe pair in the circuit just produces a very natural-sounding distortion in terms of the harmonic response. It's not harsh, but it also doesn't round off the highs excessively. It doesn't compress the signal as much as many germanium diodes seem to, but on the other hand it provides a little bit of what—to me—is exactly the right kind of compression.
Which other pedal makers are using this particular diode?
To the best of my knowledge, no one. It's a part that's been out of production for decades now, so even if someone else could identify it, I seriously doubt they'd be able to find any—I've tried a number of times myself.
So what are you working on now?
Lately, I've been focused almost entirely on putting together a good long-term arrangement for production of the KTR. This kind of thing has always been more of a challenge for me than it seems to be for anyone else, but I admit that I do have requirements—particular things I insist on—that few, if any of those other people have, so I guess that the increased difficulty is to be expected. I'm not saying that my stuff is necessarily higher quality than anyone else's, but rather that my criteria are somewhat different and that therefore the process is necessarily also somewhat different.
What is the current availability of the KTR?
The unit should be widely available—through dealers both here in the U.S. and in various other countries—by the time this interview is published. Hopefully by then I will have found time to get some kind of updated Klon website going, which of course will have contact info for the current dealers.
The top of the KTR features some text that's apparently causing controversy with some buyers: “Kindly remember: The ridiculous hype that offends so many is not of my making."
Lots of people got the point that I was trying to make and really enjoy the text, while other people find it off-putting or even insulting. It's a wry observation that I can't be held responsible for the overheated emotions that have been introduced into various Klon debates since the earliest days of the Centaur. I knew that in using that text I'd be stirring things up some, but I thought it would be interesting and fun to see how, in reacting to it, people would self-select into either the “love it" or the “hate it" group.
Photo by West Warren.
What does the future hold for Klon?
I've been thinking about this quite a bit lately. Part of me wants to work on design ideas I have—finish those designs to my satisfaction—and then make the resulting products available. The other side of me wants to either refrain from working on those ideas or work on them, finish them to my satisfaction, and then not put the resulting products out. As you may or may not know, many unscrupulous people have expropriated my hard work on the Centaur and KTR circuits and are selling pedals that incorporate my circuit—and in at least some cases, they're making a lot of money. And apparently there is nothing I can do about this from a legal standpoint.
Quite aside from the money they're making from my work, there's the question of what those pedals sound like. My understanding is that a number of those people are claiming their versions sound “identical" to mine, which—for reasons not only pertaining to the clipping diodes you asked me about—I think is very unlikely. Whatever expertise those various people may have, I'm going to go out on a limb and state my belief that it's not likely to be a good or sufficient substitute for the experience I have with the circuit: I co-designed it, I've hand-built and listened to about 8,000 Centaur units, I spent two years working hard to make sure the KTR would sound the same as the Centaur, and I've put almost 25 years of my life into it. If those other guys' pedals don't sound right, then of course Klon's reputation—and my reputation as someone who cares deeply about the quality of what goes out under the Klon name—will inevitably take a hit.
So my feeling is this: If any new product I come out with will be ripped off immediately after its release, and if unscrupulous people will again be making money off of my work, and if on top of that Klon's reputation and my own personal reputation will be at risk every time someone decides to put out his own version of one of my designs, then where is my incentive to release anything new at all? Over the past few years, I've talked with a number of other pedal designers about this stuff—good people who design their own circuits, and whose circuits have also been ripped off—and we all agree there is now an enormous disincentive for any of us to create and release new products.
From what I understand, a lot of the people posting on various online forums seem to feel that it's a wonderful thing for the pedal consumer to have more choices—how could that be bad? Here's how it could be bad: Maybe talented pedal designers—originators—will simply stop designing pedals and take their talents elsewhere to apply them to the design of other classes of products that can't be ripped off quite so easily.
Top 5 Klon Myths
Gear forums are regularly aglow with all sorts of comments about Klon. Here are the most common misconceptions.
- The Centaur is a slightly tweaked [insert name of extant pedal here] circuit. According to Klon's Bill Finnegan, “it's a much more complex circuit than the typical overdrive/boost circuit. These claims stopped almost immediately after it was reverse-engineered in 2007 and a schematic was posted online."
- Certain Centaurs sound better than others. Finnegan says he's heard this claim about earlier units, later ones, gold ones, and silver ones. “The fact is, under the hood they're all basically the same. In 1995 I made three small changes: I added a resistor to give the circuit some protection against a static charge delivered to its input—a change that has no sonic effect. I also had the circuit board redesigned with a ground plane for better grounding—again, no sonic effect except the potential for a little less hum. And I added a resistor to give the circuit a very small amount of additional low-mid response—I wanted it to have a little more roundness when used with, say, a Strat into a Super Reverb. I made no other changes."
- The KTR doesn't/can't sound as good as the Centaur. Finnegan says this claim arises because the KTR uses surface-mount parts while the Centaur (and most other pedals) use through-hole parts. “For two years my assistant, John Perotti, and I listened to hundreds of different surface-mount parts throughout the circuit," Finnegan explains. “While it wasn't an easy or pleasant process, we both feel—and now a lot of other people feel, as well—that I achieved my design goal: With careful component selection, the KTR sounds the same as the Centaur."
- You have to play really loud for the Centaur or KTR to sound good. “You need to have the output knob high enough that the signal hits the front end of your amp harder than your bypassed signal would," says Finnegan. “In other words, you need to use the unit as an overdrive in the literal sense of the term." The assumption here is that users are pairing the Centaur or KTR with an all-tube amp. “It's always a good thing if your amp is turned up enough to get the harmonic response and distortion that are engendered by tubes clipping and output transformers saturating. This is true whether you're playing through a 4-watt or a 100-watt amp."
- Certain clones sound “exactly the same" as a Klon. Finnegan's contention is that, given several factors—especially the rarity of the Centaur's germanium clipping diodes—it would be extremely difficult to create an identical-sounding overdrive/boost.
[Updated 12/12/21[
- Klon vs. Klone: 5 Affordable Stomps Go Head to Head with a Gold ... ›
- What Does It Even Mean When We Say a Pedal Is "Transparent"? - Premier Guitar ›
- Green Giant: History of the Tube Screamer - Premier Guitar ›
- Klon vs. Klone: 5 Affordable Stomps Go Head to Head with a Gold Original - Premier Guitar ›
- Why I Built This: Atelier Rosenkrantz’s Rachel Rosenkrantz - Premier Guitar ›
- A Beautifully Simple Vibrato Like No Other - Premier Guitar ›
- Spun Loud The Litigator Review - Premier Guitar ›
Valerie June’s songs, thanks to her distinctive vocal timbre and phrasing, and the cosmology of her lyrics, are part of her desire to “co-create a beautiful life” with the world at large.
The world-traveling cosmic roots rocker calls herself a homebody, but her open-hearted singing and songwriting––in rich display on her new album Owls, Omens, and Oracles––welcomes and embraces inspiration from everything … including the muskrat in her yard.
I don’t think I’ve ever had as much fun in an interview as I did speaking with roots-rock artist Valerie June about her new release, Owls, Omens, and Oracles. At the end of our conversation, after going over schedule by about 15 minutes, her publicist curbed us with a gentle reminder. In fairness, maybe we did spend a bit too much time talking about non-musical things, such as Seinfeld, spirituality, and the fauna around her home in Humboldt, Tennessee.
YouTube
If you’re familiar with June’s sound, you know how effortlessly she stands out from the singer-songwriter pack. Her equal-parts warm, reedy, softly Macy Gray-tinged singing voice imprints on her as many facets as a radiant-cut emerald—and it possesses the trademark sincerity heard in the most distinctive of singer/songwriters. Her music, overall, brilliantly shines with a spirited, contagiously uplifting glow.
Owls, Omens, and Oracles opens with “Joy, Joy!” with producer M. Ward rocking lead guitar over strings (June plays acoustic on nearly all of the tracks and banjo on one). It then recurringly dips into ’50s doo-wop chord changes, blends chugging, at times funky rock rhythms with saxophones and horns, bursts with New Orleans-style brass on “Changed” (which features gospel legends the Blind Boys of Alabama), and explores a slow soul groove with electronic guest DJ Cavem Moetavation on “Superpower.” Bright Eyes’ multi-instrumentalist Nate Walcott helmed the arrangements with guidance from Ward and June, and frequently appears on piano and Hammond organ, while Norah Jones supports with backing vocals on the folk lullaby “Sweet Things Just for You.” The entire album was recorded live to tape, which was a new experience for June.
June shares her perspective on the album and her work, overall. “It’s not ever complete or finished, your study of art,” she offers. “It’s an adventure, and it keeps getting prettier as you walk through the meadow of creating or learning new things. Every artist that you bring in has a different way of performing with you, or the audience might be really talkative or super quiet. And all of that shapes the art—so it’s ever-expansive. It’s pretty infinite [laughs], where art can take you and where it goes.... I kinda got lost there a little bit,” she muses, laughing.June’s favored acoustic guitar is this Martin 000-15M, with mahogany top, back, and sides.
Photo by Tim Bugbee/Tinnitus Photography
June didn’t connect with guitar in the beginning, but discovered her passion for it later, when the instrument became a vehicle for her self-empowerment. She took lessons as a teenager but was a distracted student, preferring to listen to her teacher share the history of blues guitarists like Big Bill Broonzy and Mississippi John Hurt. “I didn’t pick it up again until I was in my early 20s, and my band that I was in with my ex fell apart,” she says. “I still was singing and I still was hearing these beautiful voices sing me these songs, and I didn’t want to never be able to perform them. It was a terrible feeling, to be … musically stranded.
“And I was like, ‘Now, I could go get a new band and get some more accompaniment, but how ’bout I get my tail in there and keep my promise to my granddad who gave me that first guitar and actually learn how to play it, so I’ll never feel like this again.’ The goal was that I would never be musically stranded again.”
She became a solo performer, learning lap steel and banjo along with guitar, and called her style “organic moonshine roots music.” Today, she eschews picks for fingers, even when strumming chords, and is a vital blues-and-folk based stylist when she lays into her playing–especially in a live,solo setting. After two self-released albums, 2006’s The Way of the Weeping Willow and 2008’s Mountain of Rose Quartz, she connected with the Black Keys’ Dan Auerbach, who recorded and produced her 2013 album, Pushin’ Against Stone, at Nashville’s Easy Eye Sound, which helped launch her now-flourishing career.
Valerie June’s Gear
Guitars
Amps
- Fender Deluxe Reverb
Effects
- TC Electronic Hall of Fame
- MXR X Third Man Hardware Double Down booster
- J. Rockett Audio Archer boost/overdrive
Strings
- D’Addario XL Nickel Regular Light (.010–.046)
- Martin Marquis Silked Phosphor Bronze (.012–.054
Photo by Travys Owen
As we talk about art being a shared experience, June says she can be a bit of a hermit at times, but “when it’s time to share the art, then there you are. Even if you’re a painter and you just put your painting on a wall and walk away, that’s an interaction that brings you out of your studio or your bedroom to understand this whole act of co-creating—which to me is a spiritual act anyway. That’s why we’re here, to really understand those rules and layers to life. How do we co-create together?
“And I think it’s so fun,” she enthuses. “I enjoy learning, even when it’s hard. I’m like, ‘Okay, this chord is killing me right now, or this phrase.... but I’ma stick with it. And then that likens to something that I might face when I go out into the world. I’m like, ‘All right, I can get through this.’”
I suggest, “When you say ‘co-creating,’ it sounds like you mean something bigger.”
“Both in the creation of our art, but also in the creation of a life,” June replies. “’Cause how can a life be something this artistic? You get to the end of it and you’re like, ‘Wow, look at what I co-created! With all these other people, with animals, with nature, with sound that’s all around....‘ All of my life has been a piece of art or a collective creation. I imagine them like books: different lives on a shelf. And you go pick one—‘Whoa! I created a pretty fun one there!’ or, ‘Oh, man, I had no hand in that....’ Close the book, next one!” she concludes, laughing as she illustrates the metaphor with her hands.
“So does that make all of your inspirations your co-creators?” I ask.
Valerie June at one of her several Newport Folk Festival appearances, with her trusty Gold Tone banjo
Photo by Tim Bugbee/Tinnitus Photography
“Yeah! Even if they’ve gone before,” says June. “I was listening to some beautiful classical music the other day, and I was like, ‘Man, I don’t know who any of these artists are; they’re all dead and gone, but I’m just enjoying it and it’s putting me in a zone that I need to be in right now.‘ So, we’re always leaving these little seeds for even those who are coming after us to be inspired by.”
Some of her current non-musical co-creators are poets and authors, such as the poet Hafez, the philosopher Audre Lorde, poet Mary Oliver, and Robin Wall Kimmerer, a Potawatomi botanist whose works include Braiding Sweetgrass: Indigenous Wisdom, Scientific Knowledge, and the Teachings of Plants, The Serviceberry: Abundance and Reciprocity in the Natural World, and Gathering Moss: A Natural and Cultural History of Mosses.
“It’s not ever complete or finished, your study of art. It’s an adventure, and it keeps getting prettier as you walk through the meadow of creating or learning new things.”
“These books are so beautiful and show the relationship of humanity with nature and the way trees speak with each other; the way moss communicates to itself,” June explains. “Those ways of being can help humans, who always think we know so much, to learn how to work together better.”
As she’s sharing, I see her glance out her window. “Right now, I just saw a muskrat go across the pond,” she continues. “It’s about this big [holds hands about three feet apart] and it digs holes in the yard. It’s having such a great time and I’m just like, ‘Okay, you are huge, and I’m walking through the yard and falling in holes because of you [laughs]. I’m just watching you live your best life!’ And then there was a blue heron that came yesterday, and I watched it eat fish.... They’re my friends!” she exclaims, with more laughter.
Valerie June believes in the power of flowers–and all living thing–as her creative collaborators.
It might seem like we’re getting a bit off subject, but it’s residents of nature like these who are important in her creative process.
I share how, in my own approach to art, I feel as though we can always access creativity and our ideals, as long as we stay receptive to experiencing and sharing in them. June agrees, but comments that sometimes her best self only wants to sit and focus: “No more information; no more downloads, please.”
An encounter with Memphis-based blues guitarist Robert Belfour, who June frequently saw perform, expanded that perspective for her. She shares about a time she went up to him after a show: “I was like, ‘Hey, I would love to work with you on some music and maybe we could co-write a song or something.’ He was like, ‘Nope! I don’t wanna do it.’ And I said, ‘Whaaat?’ And he’s like, ‘No. I do what I do, and I do not do what anybody else does; I just do what I do.’”
Sometimes, she says, “I think that’s just as much of an outlook to have with creating as anything. It’s like, ‘Okay, I’m there, I’m where I wanna be. I don’t want to be anywhere else.’”
“That’s why we’re here, to really understand those rules and layers to life. How do we co-create together?”
Part of what’s so enjoyable about speaking with June is realizing that she truly exists on her own plane. She has no pretense, and in that, doesn’t hide some of the fears that weigh on her mind at times. But she doesn’t let those define her. It’s her easy, exuberant optimism that sparks a feeling of friendship between us, without having known each other before that afternoon. What are some of her guiding principles as an artist, I wonder?
“I sit with the idea of, ‘Who am I creating this for?’” she says, “and returning to the fact that I’m doing this for me, and, as Gillian Welch said, ‘I’m gonna do it anyway even if it doesn’t pay.’ This is what I wanna do. And reflecting on that and letting that kind of be my guiding force. It’s just something that I enjoy, that I really wanna do.”
YouTube It
From there, the conversation meanders in other directions, and June even generously asks me a few questions about my own artistic beliefs. We share about trusting your gut instinct, and walking away from situations and people who don’t serve us. This reminds her of a bigger feeling.
“With everything that these times hold for us as humans,” she shares, “from the inequality that we face to the environmental change, the political climate, and all the things that could lead us to fear or negativity.... I started to think about it, and I’m like, ‘Okay, well, maybe we are fucked! Maybe the planet is going to eject us and all of the other things are gonna come true! Well, if that’s what’s gonna happen, who do I wanna be?’
“I want to go out in a way that’s sweet or kind to other people, enjoying this experience, these last moments, and building togetherness through music. I want to co-create a beautiful life even in the face of all of that. That’s what I want to do.”
Two Iconic Titans of Rock & Metal Join Forces for a Can’t-Miss North American Trek
Tickets Available Starting Wednesday, April 16 with Artist Presales
General On Sale Begins Friday, April 18 at 10AM Local on LiveNation.com
This fall, shock rock legend Alice Cooper and heavy metal trailblazers Judas Priest will share the stage for an epic co-headlining tour across North America. Produced by Live Nation, the 22-city run kicks off September 16 at Mississippi Coast Coliseum in Biloxi, MS, and stops in Toronto, Phoenix, Los Angeles, and more before wrapping October 26 at The Cynthia Woods Mitchell Pavilion in The Woodlands, TX.
Coming off the second leg of their Invincible Shield Tour and the release of their celebrated 19th studio album, Judas Priest remains a dominant force in metal. Meanwhile, Alice Cooper, the godfather of theatrical rock, wraps up his "Too Close For Comfort" tour this summer, promoting his most recent "Road" album, and will have an as-yet-unnamed all-new show for this tour. Corrosion of Conformity will join as support on select dates.
Tickets will be available starting Wednesday, April 16 at 10AM local time with Artist Presales. Additional presales will run throughout the week ahead of the general onsale beginning Friday, April 18 at 10AM local time at LiveNation.comTOUR DATES:
Tue Sep 16 – Biloxi, MS – Mississippi Coast Coliseum
Thu Sep 18 – Alpharetta, GA – Ameris Bank Amphitheatre*
Sat Sep 20 – Charlotte, NC – PNC Music Pavilion
Sun Sep 21 – Franklin, TN – FirstBank Amphitheater
Wed Sep 24 – Virginia Beach, VA – Veterans United Home Loans Amphitheater
Fri Sep 26 – Holmdel, NJ – PNC Bank Arts Center
Sat Sep 27 – Saratoga Springs, NY – Broadview Stage at SPAC
Mon Sep 29 – Toronto, ON – Budweiser Stage
Wed Oct 01 – Burgettstown, PA – The Pavilion at Star Lake
Thu Oct 02 – Clarkston, MI – Pine Knob Music Theatre
Sat Oct 04 – Cincinnati, OH – Riverbend Music Center
Sun Oct 05 – Tinley Park, IL – Credit Union 1 Amphitheatre
Fri Oct 10 – Colorado Springs, CO – Broadmoor World Arena
Sun Oct 12 – Salt Lake City, UT – Utah First Credit Union Amphitheatre
Tue Oct 14 – Mountain View, CA – Shoreline Amphitheatre
Wed Oct 15 – Wheatland, CA – Toyota Amphitheatre
Sat Oct 18 – Chula Vista, CA – North Island Credit Union Amphitheatre
Sun Oct 19 – Los Angeles, CA – Kia Forum
Wed Oct 22 – Phoenix, AZ – Talking Stick Resort Amphitheatre
Thu Oct 23 – Albuquerque, NM – Isleta Amphitheater
Sat Oct 25 – Austin, TX – Germania Insurance Amphitheater
Sun Oct 26 – Houston, TX – The Cynthia Woods Mitchell Pavilion
*Without support from Corrosion of Conformity
MT 15 and Archon 50 Classic amplifiers offer fresh tones in release alongside a doubled-in-size Archon cabinet
PRS Guitars today released the updated MT 15 and the new Archon Classic amplifiers, along with a larger Archon speaker cabinet. The 15-watt, two-channel Mark Tremonti signature amp MT 15 now features a lead channel overdrive control. An addition to the Archon series, not a replacement, the 50-watt Classic offers a fresh voice by producing retro rock “classic” tones reminiscent of sound permeating the radio four and five decades ago. Now twice the size of the first Archon cabinet, the Archon 4x12 boasts four Celestion V-Type speakers.
MT 15 Amplifier Head
Balancing aggression and articulation, this 15-watt amp supplies both heavy rhythms and clear lead tones. The MT 15 revision builds off the design of the MT 100, bringing the voice of the 100’s overdrive channel into its smaller-format sibling. Updating the model, the lead channel also features a push/pull overdrive control that removes two gain stages to produce vintage, crunchier “mid gain” tones. The clean channel still features a push/pull boost control that adds a touch of overdrive crunch. A half-power switch takes the MT to 7 watts.
“Seven years ago, we released my signature MT 15 amplifier, a compact powerhouse that quickly became a go-to for players seeking both pristine cleans and crushing high-gain tones. In 2023, we took things even further with the MT 100, delivering a full-scale amplifier that carried my signature sound to the next level. That inspired us to find a way to fit the 100's third channel into the 15's lunchbox size,” said Mark Tremonti.
“Today, I’m beyond excited to introduce the next evolution of the MT15, now featuring a push/pull overdrive control on the Lead channel and a half-power switch, giving players even more tonal flexibility to shape their sound with a compact amp. Can’t wait for you all to plug in and experience it!”
Archon Classic Amplifier Head
With a refined gain structure from the original Archon, the Archon Classic’s lead channel offers a wider range of tones colored with gain, especially in the midrange. The clean channel goes from pristine all the way to the edge of breakup. This additional Archon version was developed to be a go-to tool for playing classic rock or pushing the envelope into modern territory. The Archon Classic still features the original’s bright switch, presence and depth controls. PRS continues to stock the Archon in retailers worldwide.
“The Archon Classic is not a re-issue of the original Archon, but a newly voiced circuit with the lead channel excelling in '70s and '80s rock tones and a hotter clean channel able to go into breakup. This is the answer for those wanting an Archon with a hotrod vintage lead channel gain structure without changing preamp tube types, and a juiced- up clean channel without having to use a boost pedal, all wrapped up in a retro-inspired cabinet design,” said PRS Amp Designer Doug Sewell.
Archon 4x12 Cabinet
As in the Archon 1x12 and 2x12, the mega-sized PRS Archon 4x12 speaker cabinet features Celestion V-Type speakers and a closed-back design, delivering power, punch, and tight low end. Also like its smaller brethren, the 4x12 is wrapped in durable black vinyl and adorned with a British-style black knitted-weave grill cloth. The Archon 4x12 is only the second four-speaker cabinet in the PRS lineup, next to the HDRX 4x12.
PRS Guitars continues its schedule of launching new products each month in 2025. Stay tuned to see new gear and 40 th Anniversary limited-edition guitars throughout the year. For all of the latest news, click www.prsguitars.com/40 and follow @prsguitars on Instagram, Tik Tok, Facebook, X, and YouTube.
For two decades, Clapton's Choice Signature Strings have delivered the legendary tone Eric Clapton relies on every time he picks up an acoustic guitar. To celebrate this milestone, Martin Guitar is introducing limited-edition 20th anniversary packaging for these fan-favorite strings--available now through March 2026.
Every limited-edition pack also gives players a chance to win a Martin 000-EC 30th Anniversary guitar--a beautifully crafted instrument with a retail value of $4,999, inspired by the Martin guitars Eric played during his legendary MTV Unplugged performance. The guitar will be awarded to one lucky winner who finds a special ticket inside a pack of strings.
Fans can also enter a second-chance giveaway online for more opportunities to win exclusive prizes, including a Martin guitar strap, poster, collectible lanyard with three custom patches, or even a year's supply of strings.This contest is open to U.S. residents only and ends March 31, 2026. No purchase necessary.
Enter now and learn more at martinguitar.com/eric-clapton-giveaway.
The anniversary release also coincides with the upcoming arrival of Unplugged: Enhanced Edition on vinyl and CD, available May 9. The iconic installment of the MTV Unplugged series--and the greatest-selling live album of all time--returns over 30 years later in an all-new extended, remixed, and remastered version. Featuring never-before-heard commentary from Eric recorded just before the original 1992 performance, the release offers fresh insight into the inspiration behind the songs and includes tracks not featured in the original MTV airing.
Crafted from 92/8 phosphor bronze, Clapton’s Choice Signature Strings are known for their warm, rich tone, smooth feel, and long-lasting performance. They're the same strings Eric uses in the studio and on stage--including during his current eight-night residency at the Nippon Budokan in Tokyo--and he calls them "the sound that I demand."
Whether you're chasing Eric's iconic tone or simply looking for strings that deliver great sound and playability, now is the perfect time to pick up a pack--available in a music store near you or online at
martinguitar.com--and celebrate two decades of signature sound.