
Sorry Kermit, it is easy being green. From recycling and repurposing old gear, to the larger movement for harvesting sustainable woods, we explore ways players can soften their impact on the natural world.
Guitar players love making messes. Slathering on too much fuzz at inopportune times, peaking VU meters, and rendering separation useless in the studio. It goes with the territory. True, sometimes you need complete isolation or the pristine precision of a Steely Dan record, but more often than not, there's something special about getting gross with your guitar.
But that's just aesthetics.
Unfortunately, guitarists also generate a lot of physical waste. Old strings, picks, batteries, and tubes need to be disposed of. Blown speakers, frayed wires, trashed amps, unwanted enclosures, and fried electronics need to be discarded as well. For better or worse, modern music making generates a small mountain of unwanted junk.
But don't fretāpun intendedāthese are solvable problems. Options and innovations abound.
In this modest dissertation, we focus on three areas: recycling waste, innovative repurposing of discarded materials, andāat what first glance might seem like a side pointāsustainable harvesting of wood.
Part I talks about garbage. Some things, like guitar strings and metal amp chassis, are easy to recycle and might even have marketable value. But others, like old tubes and single-use batteries, raise difficult questions and could be too much troubleāor just too expensiveāto recycle.
Part II profiles two innovative businessesāWallace Detroit Guitars and Analog Outfittersāthat do incredible things while repurposing old materials. Each company, in its own manner, has found a way to turn trash into treasure.
Part III is about wood. Most guitars are made of wood and many of those woods are rare and expensive. But two of those woods, rosewood and ebony, are becoming scarce. That scarcity has raised enough alarm that CITESāthe international body that deals with such mattersāhas imposed new, strict regulations. But it isn't as bleak as it sounds. We focus our attention on the important initiatives being made to develop a more sustainable model for both the growing and harvesting of these precious tonewoods.
"Above all, don't put metal in your trash." āChristopher Bosso, professor of public policy at Northeastern University
In this story, we speak with entrepreneurs, captains of industry, tenured professors, and other experts to give you an overview of these complex and sometimes complicated issues. There's a lot more to say, but consider this a thorough introduction. Ultimately, guitar players make messes, but for the most part, those messesāat least the non-musical onesācan be cleaned up.
Part I: Responsible Junk Disposal
Broken strings, worn out picks, dead batteries, fried circuits, non-functioning gear, stripped cables, and blown tubesāwhat should you do with all that junk?
Strings
Electric guitar strings are made from different types of metal and that's true for most acoustic guitar strings, too (with the obvious exception of nylon). Those metals include steel, nickel, cobalt, bronze, and various other alloys.
But guitar strings don't last forever. They wear out, break, or get crusty and gross, and at some point, you must change them. Most players change their strings on a regular basis. Many pros change them every gig.
What should you do with your old strings? Should you throw them in the trash?
"Anything with metal in it should be recycled," Christopher Bosso, a professor of public policy at Northeastern University says. "It has material value and local recycling programs actually give money for that."
D'Addario recently made string recycling easier for guitar players, with their Playback program, which allows players to drop off unwanted strings at more than 400 music retail spots around the U.S., including all Guitar Center locations. As an incentive, those who join the program earn points for recycling that can be used toward new strings or gear.
Through the Playback string recycling program, D'Addario and partner TerraCycle have recycled over 1.2 million strings in 2017. A reported 1.5 million pounds of strings are accumulated in landfills each year.
You can also take matters into your own hands. Ben Juday, the founder of Analog Outfitters, a company that builds amplifiers from repurposed Hammond organs, recommends having special bins for metal waste. "I have a couple of 5-gallon pails in my garage," he says. "Any scrap or bit of wire, brass or copper, or any little bitāanything from guitar strings to cans to little pieces of steelāI put in there and either put it out for the scrappers or take it to the scrapyard."
Scrapyards pay for junk metal, melt it down, and resell it. But don't expect to get rich recycling strings. "You would have to have a heck of a lot," Bosso says. "Scrapyards deal with significant amounts. Obviously, there's an aggregator. Cities and towns that do that place big magnets over their recyclables and anything that's metal gets pulled to a separate place. It's then sold by the ton or gets separated into the different types of metals, depending on where it is in the waste stream. More recyclables than we care to admit don't actually end up being recycled. But anything that has metal in it is of value in the marketplace. The real trick is, how do you get that into the right stream? If you put your strings into a recycling container or where the collection bin is, that's better than tossing it into the trash. Above all, don't put metal in your trash."
Batteries
Most effects pedals used to run on batteries, though the industry trend seems to be moving away from that. "I've probably sold close to 1,000 pedals and I've only had two people ask about batteries," Eric Junge, the owner of Hungry Robot Pedals, told us in an earlier interview ("Stompbox Savants," September 2016"). "I think the general consensus is, most people aren't using batteries anymore," he added. "A lot of my designs are very tight internallyāI couldn't even fit a battery into a couple of them. So my take is, 'Am I going to make this pedal bigger for the 0.1 percent of the public that's going to use a battery?'"
That said, some players still rely on batteries and they are recyclable, although most communities are not set up to handle them. "In an ideal world, you would take these single-use batteries and figure out a way to recycle them," Bosso says. "But hardly any states have recycling programs for single-use batteries. Car batteries do have a very high recycle rate. That's because they contain a valuable metal, lead, and they're big, and most times they are replaced by professionals at repair shops. You have a collection process, market value, and there is actually a process to extract the metal and other stuff from the batteries. There is a very high rate of recycling for car batteries as contrasted to consumer batteries."
In 1996, legislation was passed to phase out the use of mercury in batteries, making it legal in most states to dispose of single-use alkaline batteries via the regular trash. But single-use batteries can still be recycled at local recycling centers, along with rechargeable batteries and other electronic waste, which are restricted from being tossed in with regular trash.
Destroyed Amps, Fried Circuits, and the Forgotten Gear Graveyard
Anyone who's played long enoughāand loud enoughāhas probably fried their fair share of circuits, amps, and speakers. (For example, I fried the output circuitry on my Peavey Heritage 2x12 combo twice. Smoke billowed from the chassis and everything. The second time was at an audition. I didn't get the gig.) You can leave your old gear in the garage. You can convert it into a lamp or coffee table. Orābelieve it or notāyou can sell it. Reverb even has a category for non-functioning gear. "Keep in mind," the site claims, "there are still plenty of buyers out there who are in the market for project guitars and other fixer-upper items."
Juday agrees. "I partly got my start by buying broken equipment, fixing it, and reselling it back in my repair days. There are people who want broken gear for a bargain." But if no one wants it, bring the metal parts to the scrapyard. "Take out the speaker and metal chassis and take that to a local scrapyard. They weigh it and pay you for the scrap metal. That metal is chopped up, melted down, and turned into new steel. However, there really isn't a good way to recycle the wooden cabinet. Your best bet is to break it down with a sledgehammer and throw the wooden enclosure away."
Circuit boards and non-functioning electronics are recyclable as well. Your local scrapyard will take them. However, the EPA also lists several retailersāincluding Staples and Best Buyāthat have buy-back and drop-off programs. "If you want to see some interesting videos," Juday says, "search 'circuit board recycling.' You would not believe what they're able to do by grinding them up and melting them down. A circuit board has all kinds of precious metalsālike gold and silverāand also harmful metals like lead and cadmium. They can all be recovered through the recycling process."
Tubes, Cables, and Picks
What should you do with blown tubes? Short of converting them into shot glasses, not much. "People say, 'You should recycle them,'" Bosso says. "But the response is, 'Where do I take them? What's going to happen to them?' It's a pain in the ass to do it. Cities and towns will hold the occasional eWaste day. You bring them your eWaste and what happens, frankly, is oftentimes it is put in a big container and shipped off to developing countries where someone might try to get the metals out of it."
"Anything with metal in it should be recycled." āChristopher Bosso, professor of public policy at Northeastern University
Juday agrees. "There's not a good way of recycling tubes, which is unfortunate," he says. "The good news is they don't have very much metal in them. They do have some precious metal in there, like tungsten and other metals, but it's in such small quantities that it's not really worth anything."
Your frayed cables can be disposed of like other metals and the copper wiring can be reused for various projects. Some even claim you can use old braided and shielded cable as solder wick (Visit Instructibles.com for " How to Recycle an Old Dead Cable" article.), but the verdict is out on that.
There's also not much you can do with your old, beaten, worn-out picks. "Some plastics are recyclable," Bosso says. "They have some value in the marketplace because they can be reused. But a lot of plastics increasingly don't have much market value, so cities and towns may end up incinerating it."
However, there is a trend for converting old credit cards, vinyl records, and other hard plastics into picks. If you feel a connection to your last credit cardāor maybe if you've paid it offāyou can continue using it to make music.
Part II: Making Treasure out of Trash
Wallace Guitars uses reclaimed wood from abandoned Detroit buildings and houses. According to CEO Mark Wallace, old-growth pine dated between 1860 and 1930 yields favorable tonal characteristics.
Wallace Guitars
Wallace Detroit Guitars, based in Detroit, Michigan, builds guitars out of wood salvaged from the city's many abandoned properties. "When you're in Detroit, it's hard not to notice that there are a lot of vacant properties," Mark Wallace, the company's founder and CEO says. "It looks like these places should be torn down, thrown into a dumpster, and nobody should ever think about them. But what's exciting to me is that we're actually finding really incredible wood in those houses and turning that into instruments that stand up next to any handmade instrument."
Most of the wood comes from the Architectural Salvage Warehouse of Detroit, a local non-profit that functions as an unusual lumber yard. "We're not breaking into houses we don't own," Wallace says. "I walk into a warehouse that looks like a scene in Indiana Jones and it's full of reclaimed wood. I can see the wood, I can see the species, and they track which property a piece of wood came out of."
The most plentiful species of wood found in old Detroit houses, other than oak, is old-growth pine. "There are 60,000 vacant properties in Detroit and most of them have pine in the joist. I knew that if I could turn a pine two-by-four into a great guitar, I would have a supply that would last a very long time. I didn't know if it was going to workāso we spent a lot of time prototypingābecause pine has different characteristics from swamp ash, maple, or anything you traditionally make a guitar out of. What I discovered, which was really thrilling, is that the pine that comes out of houses that were built between 1860 and 1930 is generally pine that was grown in old-growth forests and it's very different from pine that is grown in modern forests. Typically, if you're trying to produce a two-by-four to sell at Lowe's or Home Depot, you're going to use trees that are spaced out a certain distance to maximize light and rainfall. You're going to hit them full of fertilizers to make them grow straight. You're going to trim them so they don't have any knots in them. In the old forests, every tree is competing with every other tree. They are fighting for sunlight and grow in a context of scarcity of natural resources. The reason that matters is that the growth rings you get from the old growth forests are much tighter than the growth rings you get from a modern forest. What I have is pine, and because it's so damn old, it's much more similar to ash, almost to maple, than pine you would typically expect to see in 2017. I've got this really beautiful stuff that has this really interesting performance characteristic to it."
The bodies are made from bonded-together two-by-fours and come in two styles: long grain and end grain. "The long-grain style is like racing stripes," Wallace says. "If we find trims made out of mahogany or walnut or something, we chop that up, plane it down, and slab it together. In terms of the standard pine, I really like showing off the history of the wood: the stains and the nail holes. [For the end grain], we do a long grain back and that forms the neck pocket. We then do a 5/8" cap on top where we expose the grain."
But working with these woods does pose unique challenges. "The big one is metal. Even if you use a metal detector, you still never know what's buried inside. We burn up a lot more blades than others do. Making sure the wood is dry to a consistent level is really important to us as well. Some of this stuff has been sitting outside for years."
Wallace guitars are constructed piecemeal by different teams of luthiers around Detroit. One group does the glue-ups, one does the planing, another does the sanding and finishing coat. The necks and set-ups are done separately as well, and the necks are made from maple. "I can't find enough consistent maple to do a reclaim," Wallace says. "We use Michigan maple and try to keep it in the state, but they're not reclaimed."
Illinois-based Analog Outfitters builds, or "up-cycles," amplifiers, cabinets, effects, and MIDI controllers out of parts scavenged from old Hammond Organs.
Analog Outfitters
Analog Outfitters, based just north of Champaign, in Rantoul, Illinois, builds amplifiers out of parts scavenged from old Hammond organs. "I started in 2002 as a repair/live sound company and did a lot of work on Hammond organs," Ben Juday, the company's founder says. "People would try to give me these old organs and I took a lot of them. They had no market valueāpeople were just throwing them awayāand I started messing around with them. In 2011, we started manufacturing amplifiers and it's continued since then."
Juday only dismantles organs that people don't wantāhe gets most of them for freeāand his biggest expense is hauling them back to his warehouse. "Sometimes people are upset with us for destroying these old instruments," he says. "But you've got to realize, the ones that we destroy literally [would otherwise] end up on the side of the road, in the rain, and in the landfill."
He tries to salvage, or "up-cycle," as he calls it, as much as he can from the organs as well. "We reuse the wood, the copper wiring, the amplifiers, and [even] the tubes whenever we can," he says. "Hammond used redwood, mahogany, walnut, and a lot of really good woodsāsome of which you can't even get any more. We use these premium woods in our wooden enclosures. We're not able to use all recycled materials, obviously, and I've never actually calculated the percentage, but a high percentage of the materials in our products are repurposed."
"If you saw our warehouse, we probably have about 100 organs that are not disassembled and another 200 that are." āBen Juday, Analog Outfitters
But Juday is motivated by more than just green considerations; he also thinks old organs, particularly their output transformers, sound great. He says vintage transformers, like vintage pickups, possess a special mojo not usually found in newer gear. "Many vintage transformers have that same magic sound and it has to do with how they were wound," he says. "They used methods that are more expensive to do and today people have taken shortcuts. The thing to remember about a guitar ampāa tube guitar ampāis that the output transformer is the most important part of the whole amp. It's like the transmission in your car. I don't care how good your engine is, if you don't have a way to harness that power with a good transmission, you're not going anywhere. It's the same thing with a guitar amp. The output transformer takes the energy created by that amplifier and couples it to your speaker. If you don't have a good coupling device, you're never going to get the tone that you want."
Building amps from repurposed materials isn't simple or cheap. "It's not like we just flip a few wires," Juday says. It's a painstaking process that involves transporting, dismantling, cataloging, and warehousing the reclaimed materials. "If you saw our warehouse, we probably have about 100 organs that are not disassembled and another 200 that areāthe transformers are here, the amp chassis are here, the speakers go over here, the wood is catalogued here, the wiring goes here. It's a pretty involved process." Plus, reworking an existing chassis also involves a lot of metal work, like drilling new holes and stripping away unwanted parts. "It probably takes more labor to do it the way we do, but the best form of recycling is repurposing and we really are repurposing a lot of those old parts."
Here's Analog Outfitters Scanner that was reviewed by PG and is used onstage by Doyle Bramhall II.
Analog Outfitters doesn't just build amps. They make the Scanner, which repurposes the vibrato and reverb units from old Hammond organs. They make a MIDI controller from repurposed keyboards. They use the organ's woodāwhen they're not using decommissioned street signsāto make speaker cabinets and enclosures. But they can't use everything.
"People try to give us organs from the '70s," Juday says. "We have to say no, because the wood that they used was particle chipboard, which is essentially junk, and the amps were transistor based. So those 1970s organs are of no value to us. We don't have the room to take those and to try to recycle them. But anything from the '50s or '60s, that used real solid wood and vacuum tube components, has value to us."
Part III: Wood
Bob Taylor walks in the Cameroon bush during a visit in 2017. Taylor Guitarsāin partnership with Madinter Trade, a Spain-based supplier of tonewoodsārecently purchased an ebony mill in Cameroon, an African country on the Gulf of Guinea.
Photo courtesy of Taylor Guitars
In January 2017, CITES, the Convention on International Trade in Endangered Species, which, according to their website, is "an international agreement between governments whose aim is to ensure that international trade in specimens of wild animals and plants does not threaten their survival," listed the entire Dalbergia genusāi.e. every species of rosewoodāas Appendix II. That means, in a nutshell, that rosewood is considered a species at risk and its international usage is regulated.
Needless to say, that sent the guitar world into a tizzy.
"Basically, what happened is there has been growing demand for rosewood, mainly from China," Eric Meier, the author of WOOD! Identifying and Using Hundreds of Woods Worldwide and the administrator of The Wood Database, says. "I'm not trying to completely blame the Chinese, but they have a growing middle class and a cultural tradition of rosewood furniture. The resurgence in demand for rosewood furniture is an unprecedented amount of global demand, which was the main contributing factor. Obviously, there are other factors as well, but that was the main contributing factor for the CITES decision. CITES controls how and when wood moves across international borders."
However, according to Meier, the regulation does have a provision for touring musicians. "This doesn't affect Brazilian rosewood, which has always been restricted," he says. "But for the other species of rosewood they've put the limit at 10 kilograms (about 22 pounds) and non-commercial. Basically, as long as you're not selling the instrumentāit isn't a commercial transaction, you're just traveling with itāthen it's exempted."
"One small piece of rosewood on the guitar makes it a CITES-controlled product, forever." āBob Taylor, Taylor Guitars
That isn't the case if you want to sell a guitar, even if you're selling a used instrument. "It's affected the guitar business in a negative way," Bob Taylor, the founder and CEO of Taylor Guitars, says. "People think that the 'guitar business' is conducted only by corporations. That is a false idea, because guitars are durable and last for a century or more. In that time, those guitars will have many owners. In today's world, individuals sell used guitars all day every day, often across borders. This doesn't happen with flooring, or even most furniture, for example. It's just as illegal for a person with a 20-year-old guitar to sell it across a border without all the proof and paperwork as it is for Taylor Guitars to do so with a new guitar. As the CITES rosewood regulation is currently written, it criminalizes people who have no idea or even the ability to know about the legality of a certain guitar. One small piece of rosewood on the guitar makes it a CITES-controlled product, forever. You can see the problem with this. It's relatively easy for Taylor Guitars to comply because we are a business and we deal in new guitars. We know exactly what pieces of wood are in them, their botanical names, where they came from, and we have the accompanying proof. We also know the management authorities around the world. We have the good fortune of a good reputation. We know how to file the paperwork. It isn't easy, but we can comply. It's very hard for an individual, who is the third owner of a guitar to comply, because he has to know all this, too, and prove it."
The challenge is greater for smaller, boutique buildersāespecially those who have been in business for a long time. "Most of the sources that we have always gotten wood fromāand 'we' means the guitar-building community at largeāare places that have done this forever," Amilcar Dohrn-Melendez, the materials buyer for Ryan Guitars, says. "A lot is older material, which is really good for us, and is the stuff that's harder to track. Kevin [Ryan] has been building for 30 years and he has material that is that old. Most shops do. When you get serious about building guitars, a lot of your investment early on is to get those source materials. You can use them forever and the longer they cure, the better. Guitar builders are wired to be like squirrels and keep gathering stuff. But how do you find out who the person you bought it from bought it from if you bought it 10 years ago? You can imagine, if it was longer than 15 or 20 years ago, it's just a wash in terms of how any of us kept track."
"We're married to ebony because it works," says Bob Taylor. "Substitutes don't work as well. Plus, they have their own sustainability problems." This majestic ebony tree resides in a forest in Cameroon, in Central Africa.
Photo courtesy of Taylor Guitars
Ebony is another wood the guitar building community is concerned about, especially since it's one of the best woods to use for fretboards. "As a builder, one of the things I would say about ebony is that structurally it takes frets really well," Dohrn-Melendez says. "The density and how stiff it isāeven compared to rosewoodāfrets just grab on and hold on like you want them to."
"We're married to ebony because it works," Taylor adds. "Substitutes don't work as well. Plus, they have their own sustainability problems. It's good to realize that guitars aren't the only instruments that depend upon ebony. Violins, cellos, contra-basses, also use it. I think it's better to conserve and regrow ebony than to look for alternatives."
Along those lines, Taylorāin partnership with Madinter Trade, a Spain-based supplier of tonewoodsāpurchased an ebony mill in Cameroon. Learning about woods at their source changed Taylor's opinion about what types of ebony were suitable for use. "When we first arrived, we found out from suppliers that they cut down many trees to find one with a pure black heart. Not all ebony trees are pure black and many trees were simply left to rot. That was not acceptable to us. I thought the wood was beautiful, and I felt I was in a positionānot as a supplier of ebony, but as a maker of guitarsāto change perception. Today, we are repurposing much of the colored wood into sides and backs. We had to build a lot of capabilities, but it's a great use of that material, and we don't have to depend upon using it solely on fingerboards."
Taylor Guitars is committed to replanting and conserving ebony through the Cameroon Project. The first stage of the project planted 15,000 seedlings in the Crelicam nursery, with the goal of supplying instrument manufacturers with high-quality ebony in the future.
Photo courtesy of Taylor Guitars
Part of the challenge, in terms of sustainability, is that trees take a long time to grow. "Some of the controversy in Madagascar was someone cut down protected trees in the national forest," Meier says. "The trees were 200 or 300 years old. Yes, trees can grow back, but if you just consider that that was a 200-year-old treeāthere is an element of timing. Is it realistically going to be sustainable in our lifetime?"
However, in spite of that, Taylor is planting new trees. "We have a huge project to replant ebony and it's in full swing," Taylor says. "In fact, we just signed a public-private partnership with the government of Cameroon on November 14, 2017, at the United Nations Climate Change Conference in Bonn, Germany, to cooperate on our initiative. We are partnered with the Congo Basin Institute in YaoundƩ, Cameroon, which has UCLA as the driving partner. Professor Tom Smith, the director of the Center for Tropical Research, has spent 35 years working in Cameroon on forest-related science. There is top-notch science being implemented with them as our partner. Together, we are making progress planting ebony as well as fruit and medicine trees in villages, and the villages own these projects. This first stage of the project will plant 15,000 ebony trees. My partner Vidal de Teresa from Madinter Trade in Spain oversees the work."
One thing that isn't possibleāat least not on a significant scaleāis growing these tropical trees in greenhouses. "What you need is good site location, good soil, and good seeds," Taylor says. "Hawaii is a contender to grow ebony, rosewood, and mahogany. There's a lot of mahogany already on Hawaii, so we know it grows well there. There is also the topic of improving the species through planting shoots from a good tree, thus copying that tree's qualities. With time, we may be able to crossbreed trees as well to make certain varieties that serve us well, just like it's done with edible plants. While we haven't crossbred anything yet, we have grown new trees from cuttings of trees we like."
"The environment that these trees grow in has so much to do with what they become as trees and, then by proxy, how we can use them as builders," Dohrn-Melendez says. "It's a difficult thing to manufacture. For example, you have to have a rainforest if you want to grow Brazilian rosewood. You might not have to go to Brazil, but Nebraska isn't going to cut it."
[Updated 8/10/21]
- The Environmentally Conscious Guitarist - Premier Guitar āŗ
- DIY: How to Install Onboard Effects - Premier Guitar āŗ
- Tone Tips: Is Rock Guitar Eating Itself? - Premier Guitar āŗ
- How Pedal Buyers and Builders Can Help Save the Planet - Premier ... āŗ
- The String Tension Follies Experiment, Continued - Premier Guitar | The best guitar and bass reviews, videos, and interviews on the web. āŗ
- How to Pick your Pick - Premier Guitar | The best guitar and bass reviews, videos, and interviews on the web. āŗ
- String Myths, Part 1 - Premier Guitar āŗ
- String Myths, Part 1 - Premier Guitar āŗ
- The Recording Guitarist: Should You Change Your Electric's Strings Before Tracking? - Premier Guitar āŗ
- The Recording Guitarist: Should You Change Your Electric's Strings Before Tracking? - Premier Guitar āŗ
ENGL, renowned for its high-performance amplifiers, proudly introduces the EP635 Fireball IR Pedal, a revolutionary 2-channel preamp pedal designed to deliver the legendary Fireball tone in a compact and feature-rich format.
The EP635 Fireball IR Pedal brings the raw power and precision of the ENGL Fireball amplifier into a pedalboard-friendly enclosure, offering unmatched flexibility and tonal control for guitarists of all styles. This cutting-edge pedal is equipped with advanced features, making it a must-have for players seeking high-gain perfection with modern digital convenience.
Key Features:
- Authentic Fireball Tone ā Designed after the renowned ENGL Fireball amplifier, the EP635 delivers the unmistakable high-gain aggression and clarity that ENGL fans love.
- Two Independent Channels ā Easily switch between two distinct channels, with each channelās knob settings saved independently, allowing for seamless transitions between tones.
- Built-in Midboost Function ā Enhance your tone with the integrated Midboost switch, perfect for cutting through the mix with extra punch.
- Advanced Noise Gate ā Eliminate unwanted noise and maintain articulate clarity, even with high-gain settings.
- IR (Impulse Response) Loading via USB-C ā Customize your sound with user-loadable IRs using the included software, bringing studio-quality cab simulations to your pedalboard.
- Headphone Output ā Silent practice has never been easier, with a dedicated headphone output for direct monitoring.
- Premium Build and Intuitive Controls ā Featuring a rugged chassis and responsive controls for Volume, Gain, Bass, Middle, Treble, and Presence, ensuring precise tonal shaping.
SPECS:
- Input 1/4ā (6,35mm) Jack
- Output 1/4ā (6,35mm) Jack
- Headphone Output 1/8ā(3,5mm) Jack
- 9V DC / 300mA (center negativ) / power supply, sold separately
- USB C
The Gibson EH-185, introduced in 1939, was one of the companyās first electric guitars.
Before the Les Pauls and SGs, this aluminum-reinforced instrument was one of the famous brandās first electric guitars.
Itās hard to overstate the importance of electric guitar in shaping American popular music over the last half-century. Its introduction was a revolution, changing the course of modern musical styles. Today, when we think of the guitars that started the revolution, we think of the Stratocaster and the Les Paul, guitars held against the body and fretted with the fingertips. But the real spark of this musical mutiny was the lap-steel guitar.
In the early 20th century, guitar music was moving out of the parlors of homes and into public spaces where folks could gather together and dance. Guitarists needed to project their sound far beyond where their wimpy little acoustic instruments could reach. Instrument manufacturers began experimenting with larger body sizes, metal construction, and resonators to increase volume.
Around this time, George Beauchamp began experimenting with electric guitar amplification. He settled on a design using two U-shaped magnets and a single coil of wire. Beauchamp was in business with Adolph Rickenbacker, and they decided to stick this new invention into a lap steel.
If we put on our 1930s glasses, this decision makes perfect sense. The most popular music at the time was a blend of Hawaiian and jazz styles made famous by virtuosos like Solomon āSolā HoŹ»opiŹ»i. Photos of HoŹ»opiŹ»i with a metal-body resonator aboundāone can imagine his relief at being handed an instrument that projected sound toward the audience via an amplifier, rather than back at his own head via resonator cones. Beauchamp and Rickenbacker were simply following the market.
As it turned out, the popularity of Hawaiian music gave way to swing, and electric lap steels didnāt exactly take the world by storm. But Beauchamp and Rickenbacker had proven the viability of this new technology, and other manufacturers followed suit. In 1937, Gibson created a pickup with magnets under the strings, rather than above like Beauchampās.
āWhen I plugged in the EH-185 I expected to hear something reminiscent of Charlie Christianās smooth, clean tone. But what I got was meatierācloser to what I associate with P-90s: warm and midrange-y.ā
The first page of Gibsonās āElectrical Instrumentsā section in the 1939 catalog features a glowing, full-page write-up of their top-of-the-line lap steel: the EH-185. āEverything about this new electric Hawaiian Guitar smacks of good showmanship,ā effuses the copy. āIt has smoothness, great sustaining power, and an easy flow of tone that builds up strongly and does not die out.ā
Picking up the 1940 EH-185 at Fannyās House of Music is about as close as one can get to traveling back in time to try a new one. It is just so clean, with barely any dings or even finish checking. Overall, this is a 9/10 piece, and itās a joy to behold. Speaking of picking it up, the first thing you notice when you lift the EH-185 out of the case is its weight. This is a much heavier instrument than other similar-sized lap steels, owing to a length of thick metal between the body and the fretboard. The catalog calls it āHyblum metal,ā which may be a flowery trade name for an early aluminum alloy.
This 1940 EH-185 is heavier than other lap steels in its class, thanks to a length of metal between its fretboard and body.
Photo by Madison Thorn
There are numerous other fancy appointments on the EH-185 that Gibson didnāt offer on their lesser models. Itās made of highly figured maple, with diamond-shaped decorations on the back of the body and neck. The double binding is nearly a centimeter thick and gives the instrument a luxurious, expensive look.
Behind all these high-end attributes is a great-sounding guitar, thanks to that old pickup. Itās got three blades protruding through the bobbin for the unwound strings and one longer blade for the wound strings. When I plugged in the EH-185 I expected to hear something reminiscent of Charlie Christianās smooth, clean tone. But what I got was meatierācloser to what I associate with P-90s: warm and midrange-y. It was just crying out for a little crunch and a bluesy touch. Itās kind of cool how such a pristine, high-end vintage instrument can be so well-suited for a sound thatās rough around the edges.
As far as electric guitars go, it doesnāt get much more vintage than this 1940 Gibson EH-185 Lap Steel. It reminds us of where the story of the electric guitar truly began. This EH-185 isnāt just a relicāitās a testament to when the future of music was unfolding in real time. Plug it in, and you become part of the revolution.
Sources: Smithsonian, Vintage Guitar, Mozart Project, Gibson Pre-War, WIRED, Steel Guitar Forum, Vintaxe
J Mascis is well known for his legendary feats of volume.
J Mascis is well known for his legendary feats of volume. Just check out a photo of his rig to see an intimidating wall of amps pointed directly at the Dinosaur Jr. leaderās head. And though his loudness permeates all that he does and has helped cement his reputation, thereās a lot more to his playing.
On this episode of 100 Guitarists, weāre looking at each phase of the trioās long career. How many pedals does J use to get his sound? Whatās his best documented use of a flanger? How does his version of āMaggot Brainā (recorded with bassist Mike Watt) compare to Eddie Hazelās? And were you as surprised as we were when Fender released a J Mascis signature Tele?
Editorial Director Ted Drozdowskiās current favorite noisemakers.
Premier Guitarās edit staff shares their favorite fuzz units and how and when they use them.
Premier Guitarās editors use their favorite fuzz pedals in countless ways. At any point during our waking hours, one of us could be turned on, plugged in, and fuzzed outāchasing a Sabbath riff, tracking menacing drone ambience, fire-branding a solo break with a psychedelic blast, or something else altogether more deranged. As any PGreader knows, there are nearly infinite paths to these destinations and almost as many fuzz boxes to travel with. Germanium, silicon, 2-transistor, 4-transistor, 6-transistor, octave, multimode, modern, and caveman-stupid: Almost all of these fuzz types are represented among our own faves, which are presented here as inspiration, and launch pads for your own rocket rides to the Fuzz-o-sphere.
Ted Drozdowski - Editorial Director
My favorite is my Burns Buzz, a stomp custom-made for me by Gary Kibler of Big Knob Pedals. Gary specializes in recreations of old circuits, and this Burns Buzzaround-inspired box has four germanium NOS transistors and sounds beautifully gnarly. It improves on the original, which Robert Fripp favored in early King Crimson, by adding a volume control. I went a little stir-crazy acquiring fuzzes during Covid lockdown and now have an embarrassing amount. My other current darlings are a SoloDallas Orbiter (which balances fuzz with core-signal clarity), a Joe Gore Duh (a no-nonsense, 1-knob dirt shoveler), and my Big Knob Tone Blender MkII 66, which taught me how smooth and creamy fuzz can be with carefully calibrated settings. These pedals allow me to cover all of my favorite fuzz sounds from the past 60 years. I do have one more secret weapon fuzz that only travels to the studio: an original Maestro FZ-1 that I picked up used for about $20 in the early ā90s. Itās banged up but functional, takes two 9V batteries, and is righteously juicy.
Nick Millevoi - Senior Editor
The two greatest fuzzes Iāve ever played are a Pigdog Tone Bender build and a Paul Trombetta Bone Machine. Both experiences will stick with me for decades to come. But creations by those two masters of fuzz come with a price tag high enough to keep my time with those pedals fleeting.
Instead, my favorite fuzz is an inexpensive, mass-produced pedal that hasnāt left my board since I reviewed and subsequently purchased it in 2021: the Electro-Harmonix Ripped Speaker, designed to emulate the distorted tones on ā50s and ā60s records that were created with broken or misused gear.
Retro inspiration is not all it has to offer though. The rip knob, which controls transistor bias, is the star of the show, interacting with the fuzz level to deliver everything from a smooth, mild fuzz to sputtery mayhem that can evoke a faulty channel strip or old tube combo thatās been set ablaze. I prefer to crank the rip knob and feed it to a phaser and slapback analog delay, which gives me a bit-crushed-like gnarliness. Pull back on the rip or add a boost in front of the pedal, and it has a more organic but still gated sound, which, for me, can be just the thing to set my sound apart in a more traditional setting.
For a cool $116, the Ripped Speaker, which seems to fly under most fuzz freaksā radars, might be the special something that complements the rest of your board or just a tone you turn to on occasion. Either way, itās a great deal.
Luke Ottenhof - Assistant Editor
You could give me the most powerful-sounding fuzz in the world, but if it was in a stupid-looking enclosure, I donāt know if Iād give it a second look. This is just how we operate: Vision is the sense we privilege most, even in matters of audio.
Luckily, the most seismic, monstrous fuzz Iāve ever heard also happens to come in a beautiful package. The Mile End Effects Kollaps, built by Justin Cober in Montreal, measures an elephantine 7 3/8" x 4 5/8" x 1 1/2", and its MuTron-meets-ā60s-Soviet aesthetic matches the sounds its guts produce. The Kollaps is modeled after the nasty Univox Super-Fuzz circuit, and carries a few of that pedalās hallmarks, including its use of germanium diodes and midrange boost control. Cober added a switchable Baxandall active EQ circuit, with up to 12 dB of boost and cut to both low and high frequencies. Coupled with the mid-boost toggle, this gives the Kollaps a shockingly broad range of tonality to play with.With the mids off, the Kollaps is jagged and ruthless, a deafening turbojet of upper mids and chest-vibrating lows that yanks me toward the darker, less commercially successful corners of ā90s doom and noise rock. Kicking on the EQ circuit and boosting the lows turns it titanic. With the balance (volume) and expand (gain) controls maxed, the Kollaps starts to live up to its name, crumbling into a thick, overextended chaos in a way more polite fuzz circuits rarely do.
My favorite Kollaps sounds occur when the mids are engaged, for an articulate, deeply textured fuzz sound that retains your attack. Playing with your guitarās volume knob, you can coax a range of EQ profiles and take advantage of the upper- and lower-octave content in the fuzz. With guitar volume lower, you can access some unbelievably emotive and sensitive sounds that still teeter on the edge of chaos and violence. Itās a rich, volatile circuit that gets as close as Iāve heard to a sound and physical feeling Iād call āplanet-destroying.ā
Charles Saufley - Gear Editor
My first fuzz, A Sovtek Big Muff, remains tied for first place among many favorites. The pedalās most famous virtuesācorpulence and sustaināare among the reasons I treasure it. But the way the Sovtek pairs with a Rickenbacker 330 and Fender Jaguar, which were once my two primary guitars for performance and recording, made it invaluable in various projects for a long time. Neither the Ricky nor the Jag are sustain machines, but the wailing mass of theBig Muff makes their focused voices an assetāinspiring tight, concise fuzz phrases, hooks, and riffs as well as articulate chords.
A silicon Fuzzrite clone built by good pal Jesse Trbovich (long-time member ofKurt Vileās Violators) runs second place to the Sovtek in terms of tenure, and is a very different fuzz. Itās a piercing, hyper-buzzy thing, but a perfect match for a squishy 1960s Fender Bassman head and 2x12 I adore. Perversely, I sometimes couple it with a Death By Audio Thee Ffuzz Warr Overload or Wattson FY-6 Shin-Ei Super-Fuzz clone. These tandems create chaos and chance, but sing loud and melodiously tooāat least when Iām not intentionally bathing in feedback. The Jext Telez Buzz Tone, a clone of the mid-ā60s Selmer circuit, is often my go-to now. Itās a low-gain affair compared to the other fuzzes here, and I use it in its even-lower-gain (and vintage-correct) 3-volt setting. Itās pretty noisy, but it is thick, dynamic, detailed, raunchy, and plenty trashy when the occasion demands it. Itās also a very cool overdrive when you back off the gas.Jason Shadrick - Managing Editor
I rarely need fuzz in my everyday gigs, but it's one of the most fun effects to explore when I'm noodling around. At a NAMM show a few years ago I plugged into Mythos' Argo and as soon as I hit a note my eyes lit up. The sound of the fuzz wasn't unwieldy or hard to manage. It gave me the illusion of control while the octave was the magic dust on top. I knew right then I wasn't leaving the show without one. After I spent some time with it, I became enamored by how much more the Argo can do.
It's inspired by the Prescription Electronics C.O.B. (Clean Octave Blend), so the control set is similar. The octave is always present in the signal path, but you can dial it out with the blend knob. The fuzz and volume knobs are self explanatory, but dialing the fuzz and octave knobs all the way down gives you a killer boost pedal. I find my favorite settings are at the extremes of the fuzz and blend ranges. Typically, both are either all the way up or all the way down. Another great experiment is to turn the fuzz down and then pair it with a separate drive pedal. And in octave mode, Argo is one of those pedals that inspires you to head directly for the neck pickup and stay above the 12th fret.