
Sorry Kermit, it is easy being green. From recycling and repurposing old gear, to the larger movement for harvesting sustainable woods, we explore ways players can soften their impact on the natural world.
Guitar players love making messes. Slathering on too much fuzz at inopportune times, peaking VU meters, and rendering separation useless in the studio. It goes with the territory. True, sometimes you need complete isolation or the pristine precision of a Steely Dan record, but more often than not, there's something special about getting gross with your guitar.
But that's just aesthetics.
Unfortunately, guitarists also generate a lot of physical waste. Old strings, picks, batteries, and tubes need to be disposed of. Blown speakers, frayed wires, trashed amps, unwanted enclosures, and fried electronics need to be discarded as well. For better or worse, modern music making generates a small mountain of unwanted junk.
But don't fret—pun intended—these are solvable problems. Options and innovations abound.
In this modest dissertation, we focus on three areas: recycling waste, innovative repurposing of discarded materials, and—at what first glance might seem like a side point—sustainable harvesting of wood.
Part I talks about garbage. Some things, like guitar strings and metal amp chassis, are easy to recycle and might even have marketable value. But others, like old tubes and single-use batteries, raise difficult questions and could be too much trouble—or just too expensive—to recycle.
Part II profiles two innovative businesses—Wallace Detroit Guitars and Analog Outfitters—that do incredible things while repurposing old materials. Each company, in its own manner, has found a way to turn trash into treasure.
Part III is about wood. Most guitars are made of wood and many of those woods are rare and expensive. But two of those woods, rosewood and ebony, are becoming scarce. That scarcity has raised enough alarm that CITES—the international body that deals with such matters—has imposed new, strict regulations. But it isn't as bleak as it sounds. We focus our attention on the important initiatives being made to develop a more sustainable model for both the growing and harvesting of these precious tonewoods.
"Above all, don't put metal in your trash." —Christopher Bosso, professor of public policy at Northeastern University
In this story, we speak with entrepreneurs, captains of industry, tenured professors, and other experts to give you an overview of these complex and sometimes complicated issues. There's a lot more to say, but consider this a thorough introduction. Ultimately, guitar players make messes, but for the most part, those messes—at least the non-musical ones—can be cleaned up.
Part I: Responsible Junk Disposal
Broken strings, worn out picks, dead batteries, fried circuits, non-functioning gear, stripped cables, and blown tubes—what should you do with all that junk?
Strings
Electric guitar strings are made from different types of metal and that's true for most acoustic guitar strings, too (with the obvious exception of nylon). Those metals include steel, nickel, cobalt, bronze, and various other alloys.
But guitar strings don't last forever. They wear out, break, or get crusty and gross, and at some point, you must change them. Most players change their strings on a regular basis. Many pros change them every gig.
What should you do with your old strings? Should you throw them in the trash?
"Anything with metal in it should be recycled," Christopher Bosso, a professor of public policy at Northeastern University says. "It has material value and local recycling programs actually give money for that."
D'Addario recently made string recycling easier for guitar players, with their Playback program, which allows players to drop off unwanted strings at more than 400 music retail spots around the U.S., including all Guitar Center locations. As an incentive, those who join the program earn points for recycling that can be used toward new strings or gear.
Through the Playback string recycling program, D'Addario and partner TerraCycle have recycled over 1.2 million strings in 2017. A reported 1.5 million pounds of strings are accumulated in landfills each year.
You can also take matters into your own hands. Ben Juday, the founder of Analog Outfitters, a company that builds amplifiers from repurposed Hammond organs, recommends having special bins for metal waste. "I have a couple of 5-gallon pails in my garage," he says. "Any scrap or bit of wire, brass or copper, or any little bit—anything from guitar strings to cans to little pieces of steel—I put in there and either put it out for the scrappers or take it to the scrapyard."
Scrapyards pay for junk metal, melt it down, and resell it. But don't expect to get rich recycling strings. "You would have to have a heck of a lot," Bosso says. "Scrapyards deal with significant amounts. Obviously, there's an aggregator. Cities and towns that do that place big magnets over their recyclables and anything that's metal gets pulled to a separate place. It's then sold by the ton or gets separated into the different types of metals, depending on where it is in the waste stream. More recyclables than we care to admit don't actually end up being recycled. But anything that has metal in it is of value in the marketplace. The real trick is, how do you get that into the right stream? If you put your strings into a recycling container or where the collection bin is, that's better than tossing it into the trash. Above all, don't put metal in your trash."
Batteries
Most effects pedals used to run on batteries, though the industry trend seems to be moving away from that. "I've probably sold close to 1,000 pedals and I've only had two people ask about batteries," Eric Junge, the owner of Hungry Robot Pedals, told us in an earlier interview ("Stompbox Savants," September 2016"). "I think the general consensus is, most people aren't using batteries anymore," he added. "A lot of my designs are very tight internally—I couldn't even fit a battery into a couple of them. So my take is, 'Am I going to make this pedal bigger for the 0.1 percent of the public that's going to use a battery?'"
That said, some players still rely on batteries and they are recyclable, although most communities are not set up to handle them. "In an ideal world, you would take these single-use batteries and figure out a way to recycle them," Bosso says. "But hardly any states have recycling programs for single-use batteries. Car batteries do have a very high recycle rate. That's because they contain a valuable metal, lead, and they're big, and most times they are replaced by professionals at repair shops. You have a collection process, market value, and there is actually a process to extract the metal and other stuff from the batteries. There is a very high rate of recycling for car batteries as contrasted to consumer batteries."
In 1996, legislation was passed to phase out the use of mercury in batteries, making it legal in most states to dispose of single-use alkaline batteries via the regular trash. But single-use batteries can still be recycled at local recycling centers, along with rechargeable batteries and other electronic waste, which are restricted from being tossed in with regular trash.
Destroyed Amps, Fried Circuits, and the Forgotten Gear Graveyard
Anyone who's played long enough—and loud enough—has probably fried their fair share of circuits, amps, and speakers. (For example, I fried the output circuitry on my Peavey Heritage 2x12 combo twice. Smoke billowed from the chassis and everything. The second time was at an audition. I didn't get the gig.) You can leave your old gear in the garage. You can convert it into a lamp or coffee table. Or—believe it or not—you can sell it. Reverb even has a category for non-functioning gear. "Keep in mind," the site claims, "there are still plenty of buyers out there who are in the market for project guitars and other fixer-upper items."
Juday agrees. "I partly got my start by buying broken equipment, fixing it, and reselling it back in my repair days. There are people who want broken gear for a bargain." But if no one wants it, bring the metal parts to the scrapyard. "Take out the speaker and metal chassis and take that to a local scrapyard. They weigh it and pay you for the scrap metal. That metal is chopped up, melted down, and turned into new steel. However, there really isn't a good way to recycle the wooden cabinet. Your best bet is to break it down with a sledgehammer and throw the wooden enclosure away."
Circuit boards and non-functioning electronics are recyclable as well. Your local scrapyard will take them. However, the EPA also lists several retailers—including Staples and Best Buy—that have buy-back and drop-off programs. "If you want to see some interesting videos," Juday says, "search 'circuit board recycling.' You would not believe what they're able to do by grinding them up and melting them down. A circuit board has all kinds of precious metals—like gold and silver—and also harmful metals like lead and cadmium. They can all be recovered through the recycling process."
Tubes, Cables, and Picks
What should you do with blown tubes? Short of converting them into shot glasses, not much. "People say, 'You should recycle them,'" Bosso says. "But the response is, 'Where do I take them? What's going to happen to them?' It's a pain in the ass to do it. Cities and towns will hold the occasional eWaste day. You bring them your eWaste and what happens, frankly, is oftentimes it is put in a big container and shipped off to developing countries where someone might try to get the metals out of it."
"Anything with metal in it should be recycled." —Christopher Bosso, professor of public policy at Northeastern University
Juday agrees. "There's not a good way of recycling tubes, which is unfortunate," he says. "The good news is they don't have very much metal in them. They do have some precious metal in there, like tungsten and other metals, but it's in such small quantities that it's not really worth anything."
Your frayed cables can be disposed of like other metals and the copper wiring can be reused for various projects. Some even claim you can use old braided and shielded cable as solder wick (Visit Instructibles.com for " How to Recycle an Old Dead Cable" article.), but the verdict is out on that.
There's also not much you can do with your old, beaten, worn-out picks. "Some plastics are recyclable," Bosso says. "They have some value in the marketplace because they can be reused. But a lot of plastics increasingly don't have much market value, so cities and towns may end up incinerating it."
However, there is a trend for converting old credit cards, vinyl records, and other hard plastics into picks. If you feel a connection to your last credit card—or maybe if you've paid it off—you can continue using it to make music.
Part II: Making Treasure out of Trash
Wallace Guitars uses reclaimed wood from abandoned Detroit buildings and houses. According to CEO Mark Wallace, old-growth pine dated between 1860 and 1930 yields favorable tonal characteristics.
Wallace Guitars
Wallace Detroit Guitars, based in Detroit, Michigan, builds guitars out of wood salvaged from the city's many abandoned properties. "When you're in Detroit, it's hard not to notice that there are a lot of vacant properties," Mark Wallace, the company's founder and CEO says. "It looks like these places should be torn down, thrown into a dumpster, and nobody should ever think about them. But what's exciting to me is that we're actually finding really incredible wood in those houses and turning that into instruments that stand up next to any handmade instrument."
Most of the wood comes from the Architectural Salvage Warehouse of Detroit, a local non-profit that functions as an unusual lumber yard. "We're not breaking into houses we don't own," Wallace says. "I walk into a warehouse that looks like a scene in Indiana Jones and it's full of reclaimed wood. I can see the wood, I can see the species, and they track which property a piece of wood came out of."
The most plentiful species of wood found in old Detroit houses, other than oak, is old-growth pine. "There are 60,000 vacant properties in Detroit and most of them have pine in the joist. I knew that if I could turn a pine two-by-four into a great guitar, I would have a supply that would last a very long time. I didn't know if it was going to work—so we spent a lot of time prototyping—because pine has different characteristics from swamp ash, maple, or anything you traditionally make a guitar out of. What I discovered, which was really thrilling, is that the pine that comes out of houses that were built between 1860 and 1930 is generally pine that was grown in old-growth forests and it's very different from pine that is grown in modern forests. Typically, if you're trying to produce a two-by-four to sell at Lowe's or Home Depot, you're going to use trees that are spaced out a certain distance to maximize light and rainfall. You're going to hit them full of fertilizers to make them grow straight. You're going to trim them so they don't have any knots in them. In the old forests, every tree is competing with every other tree. They are fighting for sunlight and grow in a context of scarcity of natural resources. The reason that matters is that the growth rings you get from the old growth forests are much tighter than the growth rings you get from a modern forest. What I have is pine, and because it's so damn old, it's much more similar to ash, almost to maple, than pine you would typically expect to see in 2017. I've got this really beautiful stuff that has this really interesting performance characteristic to it."
The bodies are made from bonded-together two-by-fours and come in two styles: long grain and end grain. "The long-grain style is like racing stripes," Wallace says. "If we find trims made out of mahogany or walnut or something, we chop that up, plane it down, and slab it together. In terms of the standard pine, I really like showing off the history of the wood: the stains and the nail holes. [For the end grain], we do a long grain back and that forms the neck pocket. We then do a 5/8" cap on top where we expose the grain."
But working with these woods does pose unique challenges. "The big one is metal. Even if you use a metal detector, you still never know what's buried inside. We burn up a lot more blades than others do. Making sure the wood is dry to a consistent level is really important to us as well. Some of this stuff has been sitting outside for years."
Wallace guitars are constructed piecemeal by different teams of luthiers around Detroit. One group does the glue-ups, one does the planing, another does the sanding and finishing coat. The necks and set-ups are done separately as well, and the necks are made from maple. "I can't find enough consistent maple to do a reclaim," Wallace says. "We use Michigan maple and try to keep it in the state, but they're not reclaimed."
Illinois-based Analog Outfitters builds, or "up-cycles," amplifiers, cabinets, effects, and MIDI controllers out of parts scavenged from old Hammond Organs.
Analog Outfitters
Analog Outfitters, based just north of Champaign, in Rantoul, Illinois, builds amplifiers out of parts scavenged from old Hammond organs. "I started in 2002 as a repair/live sound company and did a lot of work on Hammond organs," Ben Juday, the company's founder says. "People would try to give me these old organs and I took a lot of them. They had no market value—people were just throwing them away—and I started messing around with them. In 2011, we started manufacturing amplifiers and it's continued since then."
Juday only dismantles organs that people don't want—he gets most of them for free—and his biggest expense is hauling them back to his warehouse. "Sometimes people are upset with us for destroying these old instruments," he says. "But you've got to realize, the ones that we destroy literally [would otherwise] end up on the side of the road, in the rain, and in the landfill."
He tries to salvage, or "up-cycle," as he calls it, as much as he can from the organs as well. "We reuse the wood, the copper wiring, the amplifiers, and [even] the tubes whenever we can," he says. "Hammond used redwood, mahogany, walnut, and a lot of really good woods—some of which you can't even get any more. We use these premium woods in our wooden enclosures. We're not able to use all recycled materials, obviously, and I've never actually calculated the percentage, but a high percentage of the materials in our products are repurposed."
"If you saw our warehouse, we probably have about 100 organs that are not disassembled and another 200 that are." —Ben Juday, Analog Outfitters
But Juday is motivated by more than just green considerations; he also thinks old organs, particularly their output transformers, sound great. He says vintage transformers, like vintage pickups, possess a special mojo not usually found in newer gear. "Many vintage transformers have that same magic sound and it has to do with how they were wound," he says. "They used methods that are more expensive to do and today people have taken shortcuts. The thing to remember about a guitar amp—a tube guitar amp—is that the output transformer is the most important part of the whole amp. It's like the transmission in your car. I don't care how good your engine is, if you don't have a way to harness that power with a good transmission, you're not going anywhere. It's the same thing with a guitar amp. The output transformer takes the energy created by that amplifier and couples it to your speaker. If you don't have a good coupling device, you're never going to get the tone that you want."
Building amps from repurposed materials isn't simple or cheap. "It's not like we just flip a few wires," Juday says. It's a painstaking process that involves transporting, dismantling, cataloging, and warehousing the reclaimed materials. "If you saw our warehouse, we probably have about 100 organs that are not disassembled and another 200 that are—the transformers are here, the amp chassis are here, the speakers go over here, the wood is catalogued here, the wiring goes here. It's a pretty involved process." Plus, reworking an existing chassis also involves a lot of metal work, like drilling new holes and stripping away unwanted parts. "It probably takes more labor to do it the way we do, but the best form of recycling is repurposing and we really are repurposing a lot of those old parts."
Here's Analog Outfitters Scanner that was reviewed by PG and is used onstage by Doyle Bramhall II.
Analog Outfitters doesn't just build amps. They make the Scanner, which repurposes the vibrato and reverb units from old Hammond organs. They make a MIDI controller from repurposed keyboards. They use the organ's wood—when they're not using decommissioned street signs—to make speaker cabinets and enclosures. But they can't use everything.
"People try to give us organs from the '70s," Juday says. "We have to say no, because the wood that they used was particle chipboard, which is essentially junk, and the amps were transistor based. So those 1970s organs are of no value to us. We don't have the room to take those and to try to recycle them. But anything from the '50s or '60s, that used real solid wood and vacuum tube components, has value to us."
Part III: Wood
Bob Taylor walks in the Cameroon bush during a visit in 2017. Taylor Guitars—in partnership with Madinter Trade, a Spain-based supplier of tonewoods—recently purchased an ebony mill in Cameroon, an African country on the Gulf of Guinea.
Photo courtesy of Taylor Guitars
In January 2017, CITES, the Convention on International Trade in Endangered Species, which, according to their website, is "an international agreement between governments whose aim is to ensure that international trade in specimens of wild animals and plants does not threaten their survival," listed the entire Dalbergia genus—i.e. every species of rosewood—as Appendix II. That means, in a nutshell, that rosewood is considered a species at risk and its international usage is regulated.
Needless to say, that sent the guitar world into a tizzy.
"Basically, what happened is there has been growing demand for rosewood, mainly from China," Eric Meier, the author of WOOD! Identifying and Using Hundreds of Woods Worldwide and the administrator of The Wood Database, says. "I'm not trying to completely blame the Chinese, but they have a growing middle class and a cultural tradition of rosewood furniture. The resurgence in demand for rosewood furniture is an unprecedented amount of global demand, which was the main contributing factor. Obviously, there are other factors as well, but that was the main contributing factor for the CITES decision. CITES controls how and when wood moves across international borders."
However, according to Meier, the regulation does have a provision for touring musicians. "This doesn't affect Brazilian rosewood, which has always been restricted," he says. "But for the other species of rosewood they've put the limit at 10 kilograms (about 22 pounds) and non-commercial. Basically, as long as you're not selling the instrument—it isn't a commercial transaction, you're just traveling with it—then it's exempted."
"One small piece of rosewood on the guitar makes it a CITES-controlled product, forever." —Bob Taylor, Taylor Guitars
That isn't the case if you want to sell a guitar, even if you're selling a used instrument. "It's affected the guitar business in a negative way," Bob Taylor, the founder and CEO of Taylor Guitars, says. "People think that the 'guitar business' is conducted only by corporations. That is a false idea, because guitars are durable and last for a century or more. In that time, those guitars will have many owners. In today's world, individuals sell used guitars all day every day, often across borders. This doesn't happen with flooring, or even most furniture, for example. It's just as illegal for a person with a 20-year-old guitar to sell it across a border without all the proof and paperwork as it is for Taylor Guitars to do so with a new guitar. As the CITES rosewood regulation is currently written, it criminalizes people who have no idea or even the ability to know about the legality of a certain guitar. One small piece of rosewood on the guitar makes it a CITES-controlled product, forever. You can see the problem with this. It's relatively easy for Taylor Guitars to comply because we are a business and we deal in new guitars. We know exactly what pieces of wood are in them, their botanical names, where they came from, and we have the accompanying proof. We also know the management authorities around the world. We have the good fortune of a good reputation. We know how to file the paperwork. It isn't easy, but we can comply. It's very hard for an individual, who is the third owner of a guitar to comply, because he has to know all this, too, and prove it."
The challenge is greater for smaller, boutique builders—especially those who have been in business for a long time. "Most of the sources that we have always gotten wood from—and 'we' means the guitar-building community at large—are places that have done this forever," Amilcar Dohrn-Melendez, the materials buyer for Ryan Guitars, says. "A lot is older material, which is really good for us, and is the stuff that's harder to track. Kevin [Ryan] has been building for 30 years and he has material that is that old. Most shops do. When you get serious about building guitars, a lot of your investment early on is to get those source materials. You can use them forever and the longer they cure, the better. Guitar builders are wired to be like squirrels and keep gathering stuff. But how do you find out who the person you bought it from bought it from if you bought it 10 years ago? You can imagine, if it was longer than 15 or 20 years ago, it's just a wash in terms of how any of us kept track."
"We're married to ebony because it works," says Bob Taylor. "Substitutes don't work as well. Plus, they have their own sustainability problems." This majestic ebony tree resides in a forest in Cameroon, in Central Africa.
Photo courtesy of Taylor Guitars
Ebony is another wood the guitar building community is concerned about, especially since it's one of the best woods to use for fretboards. "As a builder, one of the things I would say about ebony is that structurally it takes frets really well," Dohrn-Melendez says. "The density and how stiff it is—even compared to rosewood—frets just grab on and hold on like you want them to."
"We're married to ebony because it works," Taylor adds. "Substitutes don't work as well. Plus, they have their own sustainability problems. It's good to realize that guitars aren't the only instruments that depend upon ebony. Violins, cellos, contra-basses, also use it. I think it's better to conserve and regrow ebony than to look for alternatives."
Along those lines, Taylor—in partnership with Madinter Trade, a Spain-based supplier of tonewoods—purchased an ebony mill in Cameroon. Learning about woods at their source changed Taylor's opinion about what types of ebony were suitable for use. "When we first arrived, we found out from suppliers that they cut down many trees to find one with a pure black heart. Not all ebony trees are pure black and many trees were simply left to rot. That was not acceptable to us. I thought the wood was beautiful, and I felt I was in a position—not as a supplier of ebony, but as a maker of guitars—to change perception. Today, we are repurposing much of the colored wood into sides and backs. We had to build a lot of capabilities, but it's a great use of that material, and we don't have to depend upon using it solely on fingerboards."
Taylor Guitars is committed to replanting and conserving ebony through the Cameroon Project. The first stage of the project planted 15,000 seedlings in the Crelicam nursery, with the goal of supplying instrument manufacturers with high-quality ebony in the future.
Photo courtesy of Taylor Guitars
Part of the challenge, in terms of sustainability, is that trees take a long time to grow. "Some of the controversy in Madagascar was someone cut down protected trees in the national forest," Meier says. "The trees were 200 or 300 years old. Yes, trees can grow back, but if you just consider that that was a 200-year-old tree—there is an element of timing. Is it realistically going to be sustainable in our lifetime?"
However, in spite of that, Taylor is planting new trees. "We have a huge project to replant ebony and it's in full swing," Taylor says. "In fact, we just signed a public-private partnership with the government of Cameroon on November 14, 2017, at the United Nations Climate Change Conference in Bonn, Germany, to cooperate on our initiative. We are partnered with the Congo Basin Institute in Yaoundé, Cameroon, which has UCLA as the driving partner. Professor Tom Smith, the director of the Center for Tropical Research, has spent 35 years working in Cameroon on forest-related science. There is top-notch science being implemented with them as our partner. Together, we are making progress planting ebony as well as fruit and medicine trees in villages, and the villages own these projects. This first stage of the project will plant 15,000 ebony trees. My partner Vidal de Teresa from Madinter Trade in Spain oversees the work."
One thing that isn't possible—at least not on a significant scale—is growing these tropical trees in greenhouses. "What you need is good site location, good soil, and good seeds," Taylor says. "Hawaii is a contender to grow ebony, rosewood, and mahogany. There's a lot of mahogany already on Hawaii, so we know it grows well there. There is also the topic of improving the species through planting shoots from a good tree, thus copying that tree's qualities. With time, we may be able to crossbreed trees as well to make certain varieties that serve us well, just like it's done with edible plants. While we haven't crossbred anything yet, we have grown new trees from cuttings of trees we like."
"The environment that these trees grow in has so much to do with what they become as trees and, then by proxy, how we can use them as builders," Dohrn-Melendez says. "It's a difficult thing to manufacture. For example, you have to have a rainforest if you want to grow Brazilian rosewood. You might not have to go to Brazil, but Nebraska isn't going to cut it."
[Updated 8/10/21]
- The Environmentally Conscious Guitarist - Premier Guitar ›
- DIY: How to Install Onboard Effects - Premier Guitar ›
- Tone Tips: Is Rock Guitar Eating Itself? - Premier Guitar ›
- How Pedal Buyers and Builders Can Help Save the Planet - Premier ... ›
- The String Tension Follies Experiment, Continued - Premier Guitar | The best guitar and bass reviews, videos, and interviews on the web. ›
- How to Pick your Pick - Premier Guitar | The best guitar and bass reviews, videos, and interviews on the web. ›
- String Myths, Part 1 - Premier Guitar ›
- String Myths, Part 1 - Premier Guitar ›
- The Recording Guitarist: Should You Change Your Electric's Strings Before Tracking? - Premier Guitar ›
- The Recording Guitarist: Should You Change Your Electric's Strings Before Tracking? - Premier Guitar ›
The two-in-one “sonic refractor” takes tremolo and wavefolding to radical new depths.
Pros: Huge range of usable sounds. Delicious distortion tones. Broadens your conception of what guitar can be.
Build quirks will turn some users off.
$279
Cosmodio Gravity Well
cosmod.io
Know what a wavefolder does to your guitar signal? If you don’t, that’s okay. I didn’t either until I started messing around with the all-analog Cosmodio Instruments Gravity Well. It’s a dual-effect pedal with a tremolo and wavefolder, the latter more widely used in synthesis that , at a certain threshold, shifts or inverts the direction the wave is traveling—in essence, folding it upon itself. Used together here, they make up what Cosmodio calls a sonic refractor.
Two Plus One
Gravity Well’s design and control set make it a charm to use. Two footswitches engage tremolo and wavefolder independently, and one of three toggle switches swaps the order of the effects. The two 3-way switches toggle different tone and voice options, from darker and thicker to brighter and more aggressive. (Mixing and matching with these two toggles yields great results.)
The wavefolder, which has an all-analog signal path bit a digitally controlled LFO, is controlled by knobs for both gain and volume, which provide enormous dynamic range. The LFO tremolo gets three knobs: speed, depth, and waveform. The first two are self-explanatory, but the latter offers switching between eight different tremolo waveforms. You’ll find standard sawtooth, triangle, square, and sine waves, but Cosmodio also included some wacko shapes: asymmetric swoop, ramp, sample and hold, and random. These weirder forms force truly weird relationships with the pedal, forcing your playing into increasingly unpredictable and bizarre territories.
This is all housed in a trippy, beautifully decorated Hammond 1590BB-sized enclosure, with in/out, expression pedal, and power jacks. I had concerns about the durability of the expression jack because it’s not sealed to its opening with an outer nut and washer, making it feel more susceptible to damage if a cable gets stepped on or jostled near the connection, as well as from moisture. After a look at the interior, though, the build seems sturdy as any I’ve seen.
Splatterhouse Audio
Cosmodio’s claim that the refractor is a “first-of-its-kind” modulation effect is pretty grand, but they have a point in that the wavefolder is rare-ish in the guitar domain and pairing it with tremolo creates some pretty foreign sounds. Barton McGuire, the Massachusetts-based builder behind Cosmodio, released a few videos that demonstrate, visually, how a wavefolder impacts your guitar’s signal—I highly suggest checking them out to understand some of the principles behind the effect (and to see an ’80s Muppet Babies-branded keyboard in action.)
By folding a waveform back on itself, rather than clipping it as a conventional distortion would, the wavefolder section produces colliding, reflecting overtones and harmonics. The resulting distortion is unique: It can sound lo-fi and broken in the low- to mid-gain range, or synthy and extraterrestrial when the gain is dimed. Add in the tremolo, and you’ve got a lot of sonic variables to play with.
Used independently, the tremolo effect is great, but the wavefolder is where the real fun is. With the gain at 12 o’clock, it mimics a vintage 1x10 tube amp cranked to the breaking point by a splatty germanium OD. A soft touch cleans up the signal really nicely, while maintaining the weirdness the wavefolder imparts to its signal. With forceful pick strokes at high gain, it functions like a unique fuzz-distortion hybrid with bizarre alien artifacts punching through the synthy goop.
One forum commenter suggested that the Gravity Well effect is often in charge as much the guitar itself, and that’s spot on at the pedal's extremes. Whatever you expect from your usual playing techniques tends to go out the window —generating instead crumbling, sputtering bursts of blubbering sound. Learning to respond to the pedal in these environments can redefine the guitar as an instrument, and that’s a big part of Gravity Well’s magic.
The Verdict
Gravity Well is the most fun I’ve had with a modulation pedal in a while. It strikes a brilliant balance between adventurous and useful, with a broad range of LFO modulations and a totally excellent oddball distortion. The combination of the two effects yields some of the coolest sounds I’ve heard from an electric guitar, and at $279, it’s a very reasonably priced journey to deeply inspiring corners you probably never expected your 6-string (or bass, or drums, or Muppet Babies Casio EP-10) to lead you to.
The author in the spray booth.
Does the type of finish on an electric guitar—whether nitro, poly, or oil and wax—really affect its tone?
There’s an allure to the sound and feel of a great electric guitar. Many of us believe those instruments have something special that speaks not just to the ear but to the soul, where every note, every nuance feels personal. As much as we obsess over the pickups, wood, and hardware, there’s a subtler, more controversial character at play: the role of the finish. It’s the shimmering outer skin of the guitar, which some think exists solely for protection and aesthetics, and others insist has a role influencing the voice of the instrument. Builders pontificate about how their choice of finishing material may enhance tone by allowing the guitar to “breathe,” or resonate unfettered. They throw around terms like plasticizers, solids percentages, and “thin skin” to lend support to their claims. Are these people tripping? Say what you will, but I believe there is another truth behind the smoke.
It’s the shimmering outer skin of the guitar, which some think exists solely for protection and aesthetics, and others insist has a role influencing the voice of the instrument. Builders pontificate about how their choice of finishing material may enhance tone by allowing the guitar to “breathe,” or resonate unfettered. They throw around terms like plasticizers, solids percentages, and “thin skin” to lend support to their claims. Are these people tripping? Say what you will, but I believe there is another truth behind the smoke.
Nitrocellulose lacquer, or “nitro,” has long been the finish of choice for vintage guitar buffs, and it’s easy to see why. Used by Fender, Gibson, and other legendary manufacturers from the 1950s through the 1970s, nitro has a history as storied as the instruments it’s adorned. Its appeal lies not just in its beauty but in its delicate nature. Nitro, unlike some modern finishes, can be fragile. It wears and cracks over time, creating a visual patina that tells the story of every song, every stage, every late-night jam session. The sonic argument goes like this: Nitro is thin, almost imperceptible. It wraps the wood like silk. The sound is unhindered, alive, warm, and dynamic. It’s as if the guitar has a more intimate connection between its wood and the player's touch. Of course, some call bullscheiße.
In my estimation, nitro is not just about tonal gratification. Just like any finish, it can be laid on thick or thin. Some have added flexibility agents (those plasticizers) that help resist damage. But as it ages, old-school nitro can begin to wear and “check,” as subtle lines weave across the body of the guitar. And with those changes comes a mellowing, as if the guitar itself is growing wiser with age. Whether a tonal shift is real or imagined is part of the mystique, but it’s undeniable that a nitro-finished guitar has a feel that harkens back to a romantic time in music, and for some that’s enough.
Enter the modern era, and we find a shift toward practicality—polyurethane and polyester finishes, commonly known as “poly.” These finishes, while not as romantic as nitro, serve a different kind of beauty. They are durable, resilient, and protective. If nitro is like a delicate silk scarf, poly is armor—sometimes thicker, shinier, and built to last. The fact that they reduce production times is a bonus that rarely gets mentioned. For the player who prizes consistency and durability, poly is a guardian. But in that protection, some say, comes a price. Some argue that the sound becomes more controlled, more focused—but less alive. Still, poly finishes have their own kind of charm. They certainly maintain that showroom-fresh look, and to someone who likes to polish and detail their prized possessions, that can be a big plus.
“With those changes comes a mellowing, as if the guitar itself is growing wiser with age.”
For those seeking an even more natural experience, oil and wax finishes offer something primal. These finishes, often applied by hand, mostly penetrate the wood as much as coating it, leaving the guitar’s surface nearly bare. Proponents of oil and/or wax finishes say these materials allow the wood to vibrate freely, unencumbered by “heavy” coatings. The theory is there’s nothing getting in the way—sort of like a nudist colony mantra. Without the protection of nitro or poly, these guitars may wear more quickly, bearing the scars of its life more openly. This can be seen as a plus or minus, I imagine.
My take is that finishes matter because they are part of the bond we have with our instruments. I can’t say that I can hear a difference, and I think a myth has sprouted from the acoustic guitar world where maybe you can. Those who remove their instrument’s finish and claim to notice a difference are going on memory for the comparison. Who is to say every component (including strings) went back together exactly the same? So when we think about finishes, we’re not just talking about tone—we’re thinking about the total connection between musician and instrument. It’s that perception that makes a guitar more than just wood and wire. The vibe makes it a living, breathing part of the music—and you.
Featuring a preamp and Dynamic Expansion circuit for punch and attack, plus switchable amp simulations.
"Like a missile seeking its target, Heatseeker will give you the explosive sound of rock! Inspired directly from the gear setup used by Angus Young,it features the most important sonic elements to match the tone of the short-pants-rock-God.
It’s no secret that a major role to his sound, along with the Marshall-brick walls, played one of the first wireless systems for guitar that quickly became a classic among guitar greats, the Schaffer Vega Diversity System."
The preamp along with the Dynamic Expansion circuit found in the wireless transmitter/receiver gave it its distinct sound. Besides boosting the signal, the preamp tightens up lower frequencies and slightly accentuates mid frequencies while the Dynamic Expansion circuit enhances the dynamic response and harmonics of the signal giving punch and attack to ensure that it will cut through the mix. Instead of opting for a prefix setting for the Dynamic Expansion circuit as found in the original unit, we have re-imagined our version with the enhanced knob on the Heatseeker to have more control over the guitar tone’s dynamic response. Setting it around 10 o‘clock is a good starting point to add some extra sparkle. Max it out to bring back to life even the most dull and colorless sounds.
Utilizing an all-analog JFET circuit, running on 27 volts via an internal voltage boost (DO NOT plug higher than 9V DC power supply), we have captured the tone and feel of three British tube amplifiers, synonymous with the sound of rock and roll, with an excellent clean-to-mean dynamic response. With the flip of a toggle switch, you can capture the sound and feel of a JTM45, 1959 Super Lead, or JMP 2203. A smart switching circuit follows the signal path and respective gain stages tuned for each amp and combines them with an actual Marshall style EQ and power amp simula-tion circuit for thundering rock tones. Angus Young usually plugs into Channel 1 or High Treble input of his JTM45s and Super Leads so we opted for that sound when we started visualizing Heatseeker on the drawing board. We have also extended the range of the presence control beyond the original so that the user will be able to match the pedal to any amp or gear setup. The master volume offers plenty of output so that you can also use the pedal as a preamp and plug it into a clean power amp or straight to your DAW. Note that the pedal doesn’t feature any speaker simulation circuit so we recommend using a separate hardware or software guitar speaker simulation when going direct to DAW or a full-range speaker.
A new feature to our booster/drive + amp-in-a-box line of pedals, recreating legendary sounds, is the switchable WoS (Wall of Sound) circuit. We have carefully tuned this circuit at the output of the AMP section of the Heatseeker to open up the soundstage by increasing the output, adding thundering lows, and thickening high mid frequencies. Imagine standing in front of a wall loaded with Marshall amp heads and 4x12 speaker cabinets, grabbing your SG, and hitting a chord. You will be blown away by the sound projection! In combination with the tube power amp simulation and the enhanced circuit of the right section, we’ve made sure that the pick attack will be as dynamic as it gets, so¥er picking will produce clean and slightly crunchy sounds, and hard picking will give explosive distorted sounds! While primarily designed for Angus Young sounds, Heatseeker will definitely open the door to countless other guitar-great tones that use these Marshall amps and/or the Schaffer Vega Diversity System. Think of KISS, Peter Frampton, and Van Halen to name a few.
Like our other dual overdrive/amp-in-a-box designs, Heatseeker features a passive effects loop to give you the option to connect your beloved pedals between the preamp/enhancer and amp-in-a-box circuit or use the two sections as separate and independent effects when using an external bypass switcher/looper. SND is the output of the BOOST/ENHANCE section, RTN is the input of the AMP section. SND is connected to RTN when no instrument jacks are inserted in the effects loop. Note that all pedals inserted in the passive effects loop are still in the signal chain when any or both sections of the Heatseeker are in bypass mode.
Heatseeker features a power-up bypass/engage pre-set function for the footswitches. You can change the default function by holding down the footswitch(es) during power-up. That way you can select which state your pedal will go to when you plug the power supply. This function comes in especially handy to people who use remote pedal switchers/loopers as they only set the state of the pedal once and then operate from the controller.
Street/MAP Price: $279
For more information, please visit crazytubecircuits.com.
Creed extend their sold-out Summer of ’99 Tour with 23 additional dates.
Produced by Live Nation, the dates begin July 9 at Rupp Arena in Lexington, KY and wrap August 20 at the Scotiabank Saddledome in Calgary, AB with support from 3 Doors Down, Daughtry, Mammoth WVH and Big Wreck. *Check individual dates for lineup in each market.
When it kicked off in 2024, The Summer of ’99 Tour quickly became “one of the most anticipated tours of the summer” (USA Today) and “one of the hottest rock tickets of the year” (Billboard) for a return that “may be something this industry has never seen” (Pollstar). To date, CREED’s Scott Stapp, Mark Tremonti, Brian Marshall, and Scott Phillips have performed over 60 sold-out concerts throughout North America, selling over 800,000 tickets and breaking venue records in multiple markets.
“Thirty years in, it’s been a blessing to pick up right where we left off with longtime fans and to meet the next generation for the first time. It’s been an incredible ride, and we aren’t done, so here’s to a ‘Summer’ that never ends. We’ll see you on the road,” states Scott Stapp.
Creed will close out 2024 with shows in Las Vegas, NV (Dec. 30 & Dec. 31) and their newly announced dates in 2025 will follow their already sold-out Summer of ’99 and Beyond cruise sailing April 9– April 13 from Miami to Nassau with Sevendust, Hoobastank, Lit, Hinder, Fuel and more. Also in April, the band - whose audience has included fans of mainstream, rock, and country for over 25 years - will perform at Stagecoach.
For more information on all Creed tour dates as well as the opportunity to purchase entry into Mark Tremonti’s guitar clinic can be found at https://creed.com.
Tour Dates
CREED: SUMMER OF ‘99 TOUR 2025 DATES:
3DD – 3 Doors Down / D – Daughtry / BW – Big Wreck / MWVH – Mammoth WVH
Wed Jul 09 | Lexington, KY | Rupp Arena – 3DD/MWVH
Fri Jul 11 | Syracuse, NY | Empower Federal Credit Union Amphitheater at Lakeview – 3DD/MWVH
Sat Jul 12 | Camden, NJ | Freedom Mortgage Pavilion – 3DD
Tue Jul 15 | Wantagh, NY | Northwell at Jones Beach Theater – D/MWVH
Wed Jul 16 | Scranton, PA | The Pavilion at Montage Mountain – D/MWVH
Sun Jul 20 | Columbus, OH | Schottenstein Center – 3DD/MWVH
Tue Jul 22 | Hartford, CT | Xfinity Theatre – 3DD/MWVH
Thu Jul 24 | Charleston, SC | Credit One Stadium – 3DD/MWVH
Sat Jul 26 | New Orleans, LA | Smoothie King Center – 3DD/MWVH
Sun Jul 27 | Memphis, TN | FedExForum – 3DD/MWVH
Tue Jul 29 | Wichita, KS | INTRUST Bank Arena – D/MWVH
Fri Aug 01 | Lincoln, NE | Pinnacle Bank Arena – D/MWVH
Sat Aug 02 | Ridgedale, MO | Thunder Ridge Nature Arena – D/MWVH
Mon Aug 04 | Albuquerque, NM | Isleta Amphitheater – D/MWVH
Wed Aug 06 | Chula Vista, CA | North Island Credit Union Amphitheatre – D/MWVH
Thu Aug 07 | Palm Desert, CA | Acrisure Arena at Greater Palm Springs – 3DD/MWVH
Sat Aug 09 | Mountain View, CA | Shoreline Amphitheatre – 3DD/MWVH
Sun Aug 10 | Stateline, NV | Lake Tahoe Outdoor Arena at Harveys – 3DD/MWVH (Not a Live Nation date)
Wed Aug 13 | Ridgefield, WA | RV Inn Style Resorts Amphitheater – 3DD/MWVH
Thu Aug 14 | Auburn, WA | White River Amphitheatre – 3DD/MWVH
Sat Aug 16 | Vancouver, BC | Rogers Arena – BW/MWVH
Tue Aug 19 | Edmonton, AB | Rogers Place – BW/MWVH
Wed Aug 20 | Calgary, AB | Scotiabank Saddledome – BW/MWVH
Previously Announced CREED Dates:
Sat Dec 28 | Durant, OK | Choctaw Casino & Resort (Sold Out)
Mon Dec 30 | Las Vegas, NV | The Colosseum
Tue Dec 31 | Las Vegas, NV | The Colosseum
Apr 9 – Apr 13 | Miami – Nassau | Summer of ’99 and Beyond Cruise (Sold Out)
Sat Apr 26 | Indio, CA | Stagecoach