Premier Guitar features affiliate links to help support our content. We may earn a commission on any affiliated purchases.

Mod Garage: The Scott Henderson S-Style Wiring

Mod Garage: The Scott Henderson S-Style Wiring

Fig. 1

illustration courtesy of SINGLECOIL (www.singlecoil.com)

This guitar wiring is special in that the two tone controls are freely assigned, and the tone control is bypassed in the two in-between positions. Let’s go under the hood.

Hello and welcome back to Mod Garage. This month, we’ll have a look at the Scott Henderson Strat-style wiring and what it means to bypass the tone control for certain pickup-switching positions.

Bypassing the tone control in a guitar circuit has become popular in recent years, so let’s explore how to do it. We’ve discussed this before in the context of using no-load pots for the tone control. A no-load pot will be electrically out of the circuit when it’s fully opened, so the pot is no longer part of the wiring, and will add no load to the circuit. This way you will have no high-end dampening and the tone is a tad louder, which can be a good thing or not, depending on your personal preferences.

This works great but requires that you open the tone pot(s) if you want this very direct sound. Some players like to have a kind of preset without tone control so there is no additional action they have to take. So, the basic idea of bypassing the tone controls is to transfer it to the pickup-selector switch rather than using no-load pots. There’s no law against combining this mod with no-load pots for the tone control, so you still have the opportunity to use it for sounds where the tone control is engaged.

The credits for this wiring are given to John Suhr, but it’s unknown if he came up with this special wiring during his time as a Senior Master Builder in the Fender Custom Shop, or later, after he started his own business in 1997.

The preset idea is not a new one. Fender has used it since the early ’50s, and the basic idea behind it is still the same. Imagine the following scenario: You’re playing the bridge pickup on your guitar with the corresponding tone pot set to 7 to add some warmth to your tone. In the middle of a song, you need to switch to another pickup that is connected to the same tone pot, but you need the tone pot fully opened to cut through the mix with this pickup setting. Two steps are required now: You need to switch to the desired pickup position, and you need to open the tone pot. Wouldn’t it be nice to have this happen by only dialing in the other pickup position? This is exactly the idea behind bypassing the tone control.

To illustrate, I chose the personal S-style wiring of the award-winning fusion, jazz, and blues guitarist Scott Henderson. The credits for this wiring are given to John Suhr, but it’s unknown if he came up with this special wiring during his time as a senior master builder in the Fender Custom Shop, or later, after he started his own business in 1997.

Henderson is best known for his solo work but also for his band Tribal Tech, as well as for playing with Chick Corea and the Zawinul Syndicate. Henderson released his first solo album, Dog Party, in 1994 and has six solo albums to date. He’s also a teacher at the Guitar Institute of Technology, now known as the Musicians Institute in Hollywood, California. His signature S-style guitar is built by the Suhr company. Henderson and John Suhr got to know each other while Suhr was still working at the Fender Custom Shop, and Henderson became one of the first endorsers for Suhr Guitars.

Henderson wanted an exclusive tone control for the bridge pickup and full clarity in the two in-between pickup positions, so this wiring is exactly what he was looking for.

Henderson’s personal wiring is basically a standard Stratocaster wiring you all know:

  • bridge pickup alone
  • bridge and middle pickup together in parallel
  • middle pickup alone
  • middle and neck pickup together in parallel
  • neck pickup alone

What makes this wiring special is that the two tone controls are freely assigned, and the tone control is bypassed in the two in-between positions. So, the switching matrix for the Henderson wiring goes like this:

  • bridge pickup alone with tone control #1
  • bridge and middle pickup together in parallel with no tone control
  • middle pickup alone with tone control #2
  • middle and neck pickup together in parallel with no tone control
  • neck pickup alone with tone control #2

Henderson wanted an exclusive tone control for the bridge pickup and full clarity in the two in-between pickup positions, so this wiring is exactly what he was looking for. Another benefit is that the bypass of the tone controls for the in-between positions is slightly compensating for the little volume loss, which is the nature of the (passive) beast when you combine two pickups in parallel.

In a Strat with two tone controls, changing the standard 5-way pickup selector switch for a 5-way super-switch is mandatory because you can’t do all this with only two switching stages. We don’t need all four switching stages of the 5-way super-switch, so one stage will stay unconnected.

Technically, these are 4P5T wafer switches, and they’re available as open frame as well as PCB-based versions. These switches are physically a lot larger than the standard ones, so depending on what guitar you have, you can run into massive problems to make them fit without rerouting your electronic compartment. Always check this before you buy such a switch to avoid any unpleasant surprises. To make the open version from Fender fit, you need at least 21 mm of space for the switch, but it’s better to have 25 mm to avoid any problems with the soldering terminals.

So here it is, the Henderson wiring as seen in Fig. 1. This wiring uses three 250k pots, a 0.047 µF tone cap, and no treble-bleed network on the volume pot.

That’s it for now. Next month, we’ll continue the tone-pot-bypass journey by looking at a Telecaster wiring, so stay tuned.

Until then ... keep on modding!

Reader: Federico Novelli
Hometown: Genoa, Italy
Guitar: The Italian Hybrid

Reader Federico Novelli constructed this hybrid guitar from three layers of pine, courtesy of some old shelves he had laying around.

Through a momentary flash, an amateur Italian luthier envisioned a hybrid design that borrowed elements from his favorite models.

A few years ago, at the beginning of Covid, an idea for a new guitar flashed through my mind. It was a semi-acoustic model with both magnetic and piezo pickups that were mounted on a soundboard that could resonate. It was a nice idea, but I also had to think about how to make it in my tiny cellar without many power tools and using old solid-wood shelves I had available.

I have been playing guitar for 50 years, and I also dabble in luthiery for fun. I have owned a classical guitar, an acoustic guitar, and a Stratocaster, but a jazz guitar was missing from the list. I wanted something that would have more versatility, so the idea of a hybrid semi-acoustic guitar was born.

I started to sketch something on computer-aided design (CAD) software, thinking of a hollowbody design without a center block or sides that needed to be hot-worked with a bending machine. I thought of a construction made of three layers of solid pine wood, individually worked and then glued together in layers, with a single-cutaway body and a glued-in neck.

For the soundboard and back, I used a piece of ash and hand-cut it with a Japanese saw to the proper thickness, so I had two sheets to fit together. Next, I sanded the soundboard and bottom using two striker profiles as sleds and an aluminum box covered in sandpaper to achieve a uniform 3 mm thickness. A huge amount of work, but it didn't cost anything.

“It was a nice idea, but I also had to think about how to make it in my tiny cellar without many electric tools and out of old solid-wood shelves I had available.”

The soundboard has simplified X-bracing, a soundhole with a rosewood edge profile, and an acoustic-style rosewood bridge. For the neck, I used a piece of old furniture with straight grain, shaped it to a Les Paul profile, and added a single-action truss rod. The only new purchase: a cheap Chinese rosewood fretboard.

Then, there was lots of sanding. I worked up to 400-grit, added filler, primer, and transparent nitro varnish, worked the sandpaper up to 1,500-grit, and finally polished.

Our reader and his “Italian job.”

For electronics, I used a Tonerider alnico 2 humbucker pickup and a piezo undersaddle pickup, combined with a modified Shadow preamp that also includes a magnetic pickup input, so you can mix the two sources on a single output. I also installed a bypass switch for power on/off and a direct passive output.

I have to say that I am proud and moderately satisfied both aesthetically and with the sounds it produces, which range from jazz to acoustic and even gypsy jazz. However, I think I will replace the electronics and piezo with Fishman hardware in the future.

Read MoreShow less

Billy Corgan and The Machines of God announce 'A Return to Zero Tour' kicking off on June 7th, featuring classic tracks and deep cuts from iconic albums. Tickets available for presale on April 1st. Don't miss this unforgettable experience! Tour dates include Baltimore, Boston, New York, and more.

Read MoreShow less
- YouTube

Cut the cord! PG contributor Tom Butwin goes hands-on with three compact wireless guitar systems from Positive Grid, NUX, and Blackstar. From couch jams to club gigs, find the right unit for your rig and playing style.

Read MoreShow less

An easy guide to re-anchoring a loose tuning machine, restoring a “lost” input jack, refinishing dinged frets, and staunching a dinged surface. Result: no repair fees!

Pardon my French, but I’m about to misethe hell out of some en scenein this article about do-it-yourself guitar repair. Buckle-vous up.

The Guitarist is in the middle of double-tracking a solo. It’s not quite right. Creative juices are flowing, but at any moment, the gate could slam shut. Their social media feed is stagnant, and the algorithm thirsts for content. The studio is 80 bucks an hour. That new boutique fuzz pedal would sound great on this track, surely? It would, of course, as these things are the cure for all problems, but it rests just out of reach.

Desperate for a solution, the Guitarist rests their perfect new guitar against the warm tube amp–only for a moment … but a horrible amplified bwaang from wood, string, and concrete’s violent meeting breaks the temporary silence as gravity muscles potential into the kinetic. The Guitarist breathes a defeated “aw, man,” like a loosened balloon farting hopelessly across an empty room. The gate closes, juices no longer loose, locked, impenetrable by any transistor-based effect. And it’s time to assess the damage.”

Read MoreShow less