
From $99 to $4000, we look at 18 tools for micing your cab.
Think about the inspiration we’ve all had from hearing an amazing electric guitar recording. I know it’s literally altered my career path, and I’m sure countless others will have similar stories. But getting that perfect sound from the speaker to tape is no easy task. There are infinite combinations of pickups, strings, amps, cables, instruments and players, each with their own tonality (and an endless number of opinions, too!). However, right up there in the order of importance is certainly the choice of microphone. Each selection will add a little something different to the sound, and no one choice is always the right one.
The Mics
Shure SM57 List: $170 Certainly a classic, this reliable, rugged dynamic mic has a frequency response of 40Hz–15kHz. Its relatively tight cardioid polar pattern and ability to take high volumes make it a first-call on many sessions. Due to its aggressive mid-range growl, it’s a perfect companion to blend with “darker” mics. When it comes to bang for the buck, the SM57 is hard to beat. Download Audio | Royer R-121 List: $1395 The R-121 is a dynamic Ribbon mic with a Figure-8 polar pattern. Like other ribbons, it’s warm, creamy and natural. Unlike most other ribbons, it was built to take a max SPL rating of 135dB, making it a great cabinet mic. Also, by turning it around and reversing the phase, the back is sonically brighter at distances of two feet and closer. We found its face-front sound to be one of our favorites overall for warmth and character—a perfect blend with an SM57. Download Audio | Neumann U 87 (Ai) List: $3998 Another legendary classic, this large diaphragm mic has three polar patterns (cardioid, omni, figure-8). We used an older model in cardioid mode, but the new Ai version has circuitry to increase the headroom by 10dB. With the rear switch attenuated, the U 87 can take up to 127dB and has a frequency response of 20Hz–20kHz. You can hear the “beef” on both clean and distorted parts, and very nice attitude on distorted sound. Download Audio |
Shure SM58 List: $188 Almost always thought of as a vocal mic, sometimes you just have to put one up on a cabinet. Like the SM57, its price, midrange peak, 50Hz–15kHz frequency response and ability to handle massive gain make it a mic drawer classic. Essentially a 57 with a different grill and more girth, it sounded surprisingly good on the clean parts. Download Audio | Earthworks QTC1 (Same as QTC40) List: $1295 An omni? Sure, why not! The QTC’s small diaphragm gives it a realistic and accurate sound. A super-wide frequency range of 4Hz–40kHz and max acoustic input of 142dB SPL make it a great option. It had a very natural sound—what you heard in the room is what came out of the speakers. Download Audio | Sennheiser MD 421 List: $598 A cardioid mic with a five-position bass rolloff (to help eliminate proximity effect), this mic is a classic tone heard for decades now. Its frequency response of 30Hz–17kHz and ability to take very high SPLs give it a full, round sound. It works great with other mics, and by itself sounded warm and full, with slightly rolled off highs. Download Audio |
Beyerdynamic M 160 List: $799 The M 160 is a hypercardioid, dynamic ribbon mic that has two ribbons arranged one above the other a half-millimeter apart. It’s got a max SPL of 129dB and a frequency response of 40Hz–18 kHz. Its big, ribbony sound is always a favorite for good reason. Download Audio | Audix i5 List $179 The i5 is a dynamic, general-purpose mic with a cardioid polar pattern. It has a frequency response of 50Hz–16kHz and a max SPL of 140dB—so it can take it hard. It sounds like a 57, but with additional presence and upper mid clarity, and would make a great partner with a MD 421 or Royer. Download Audio | Audio-Technica AT4060 List: $1665 This is a large cardioid, vacuum tube condenser with a large, 2-micron-thick gold diaphragm and separate power supply. It features 20Hz–20kHz specs and can take up to 131dB SPL, which is a lot for a tube mic. While it may not be the best call by itself, it would make a nice mic to put back around 3–4 feet for some additional room sound. Download Audio |
Coles 4038 List: N/A The 4038 is a studio ribbon mic designed by the BBC for broadcasting and recording. It’s bidirectional (figure-8) with a frequency response of 30Hz–15kHz and can take up to 125dB SPL—although we had to move this back to 11 inches for breakup factor. Another classic ribbon sound with the softened highs and warm overall tone, there’s no denying this one. Download Audio | Audio-Technica AT4047/SV List: $745 This good-looking condenser mic has a wide frequency response of 20Hz–18kHz and the ability to take up to 159dB SPL with the 10dB pad in. There’s a switchable 80Hz hi-pass filter as well, and it features a gold plated dualdiaphragm capsule design. It captured both crisp highs and a well-rounded bottom. Download Audio | AKG 414 B-ULS List: $1349 Wow, another classic. The 414 has five switchable polar patterns (omni, wide cardioid, cardioid, hyper cardioid, figure-8) and a large, 1-inch diaphragm. It’s got 20Hz–20kHz frequency response and a max SPL of up to 158 with -18dB of attenuation switched in. We set it to cardioid, no pad. This mic cuts through a mix well and has lots of attitude. Download Audio |
EV RE20 List: $750 Often referred to as the “donkey dick” mic, this large diaphragm dynamic cardioid monster routinely seen and heard on radio/TV broadcasts has a frequency response of 45Hz–18kHz. Commonly used in guitar session work, it makes a great complement to other mics, such as the 57. We used a PL15, which is basically the same model. It’s got great low end in both the clean and distorted parts… smooth upper mids and not too much high end. Download Audio | Shure SM7B List: $619 This dynamic is often viewed as a radio mic, but it has a smooth sound and 50Hz–20kHz frequency response. There are bass roll-off and mid-range emphasis switches, but we set it flat. With an immediately pleasing sound both clean and distorted, it’s got a bottom-heavy focus that works great alone or in conjunction with a brighter mic—great attitude. Download Audio | M-Audio Luna List: $399 Now available as the Luna II, this cardioid condenser has a large, solid brass capsule, Class-A electronics and a 10dB pad, which lets it handle up to 140dB SPL. It has a good, full low end and smooth mids, especially on the distorted tracks, and is well balanced. Download Audio |
Heil PR 40 List: $375 A dynamic supercardioid mic from Heil Sound, it features a large low-mass aluminum diaphragm, a heavy steel case and a wide frequency response from 28Hz–18kHz. Very nice bottom and high end, almost nondescript in a positive way. It sounds really cool with a Coles 4038, or the like. Download Audio | B&K 4006 List: $1925 (as DPA 4006) Now labeled under the DPA name, this high-end, phantom-powered omni mic is often used in classical recordings. Its got an extremely linear frequency response from 20Hz–20kHz, and can take up to 143dB max SPL. It sounds quite natural, with non-extended highs and lows that give you back just what you put in front of it. Download Audio | Reslo List: N/A A classic English ribbon mic from the early sixties, it’s got a frequency response of 40Hz–15kHz… no wonder it can be heard on some of those classic Beatles recordings. The output sounds like analog tape through an old tube console. Download Audio |
Below, Grammy Award Winning engineer/producer Pete Moshay and I put a nice selection of mics up on an electric guitar session, all ranging in street price from $99 to over $4000. From the desert island Shure SM57 to a vintage Coles 4038 ribbon, there’s something for everyone.
The Method
I recorded two guitar licks directly into Pro Tools HD at 24-bit, 48kHz using a Creation Audio Labs MW1 and a stock early-nineties American Standard Telecaster, set to the middle pickup position. We then fed that output into a Mesa Boogie MKIV (Full power, Triode and Simul-Class settings) head and a Boogie 4x12 cabinet with Black Shadow speakers in Moshay’s A-frame live room (plugged into a balanced power source).
Using our ears to pick the best speaker, we then placed each mic directly on axis, about two inches from the grill, just to the left outside the center of the cone. We used a Little Labs IBP to run the signal from Pro Tools to the amp, bringing the +4dB line level signal to guitar level. Each lick was recorded first on the Boogie’s Channel 1 clean setting, then on Channel 3 with some tube saturation. We used a Focusrite ISA 828 on Medium impedance (which we felt imparted the least coloration on the varied mic impedances), running the signal directly into Pro Tools with the preamp’s A/D converters, all clocked with an Apogee Electronics Big Ben. No patch bay was used.
The only adjustments made were to maintain a consistent signal where the peaks hit around -3–4 dB, using a 1kHz tone sent into the amp at approximately -25dB. With all the various types, models and dynamic ranges of the mics, it’s not a perfect science to get exact measurements and levels, but we tried to keep everything as even as possible.
Shure SM57
Certainly a classic, this reliable, rugged dynamic mic has a frequency response of 40Hz–15kHz. Its relatively tight cardioid polar pattern and ability to take high volumes make it a first-call on many sessions. Due to its aggressive mid-range growl, it’s a perfect companion to blend with “darker” mics. When it comes to bang for the buck, the SM57 is hard to beat.
$99 street
shure.com
Royer R-121
The R-121 is a dynamic Ribbon mic with a Figure-8 polar pattern. Like other ribbons, it’s warm, creamy and natural. Unlike most other ribbons, it was built to take a max SPL rating of 135dB, making it a great cabinet mic. Also, by turning it around and reversing the phase, the back is sonically brighter at distances of two feet and closer. We found its face-front sound to be one of our favorites overall for warmth and character—a perfect blend with an SM57.
$1,295 street
royerlabs.com
Neumann U 87 Ai
Another legendary classic, this large diaphragm mic has three polar patterns (cardioid, omni, figure-8). We used an older model in cardioid mode, but the new Ai version has circuitry to increase the headroom by 10dB. With the rear switch attenuated, the U 87 can take up to 127dB and has a frequency response of 20Hz–20kHz. You can hear the “beef” on both clean and distorted parts, and very nice attitude on distorted sound.
$3,650 street
en-de.neumann.com
Shure SM58
Almost always thought of as a vocal mic, sometimes you just have to put one up on a cabinet. Like the SM57, its price, midrange peak, 50Hz–15kHz frequency response and ability to handle massive gain make it a mic drawer classic. Essentially a 57 with a different grill and more girth, it sounded surprisingly good on the clean parts.
$99 street
shure.com
Earthworks QTC1
An omni? Sure, why not! The QTC’s small diaphragm gives it a realistic and accurate sound. A super-wide frequency range of 4Hz–40kHz and max acoustic input of 142dB SPL make it a great option. It had a very natural sound—what you heard in the room is what came out of the speakers.
$1,998 street
earthworksaudio.com
Sennheiser MD 421
A cardioid mic with a five-position bass rolloff (to help eliminate proximity effect), this mic is a classic tone heard for decades now. Its frequency response of 30Hz–17kHz and ability to take very high SPLs give it a full, round sound. It works great with other mics, and by itself sounded warm and full, with slightly rolled off highs.
$399 street
en-us.sennheiser.com
Beyerdynamic M 160
The M 160 is a hypercardioid, dynamic ribbon mic that has two ribbons arranged one above the other a half-millimeter apart. It’s got a max SPL of 129dB and a frequency response of 40Hz–18 kHz. Its big, ribbony sound is always a favorite for good reason.
$699 street
north-america.beyerdynamic.com
Audix i5
The i5 is a dynamic, general-purpose mic with a cardioid polar pattern. It has a frequency response of 50Hz–16kHz and a max SPL of 140dB—so it can take it hard. It sounds like a 57, but with additional presence and upper mid clarity, and would make a great partner with a MD 421 or Royer.
$99 street
audixusa.com
Audio-Technica AT4060
This is a large cardioid, vacuum tube condenser with a large, 2-micron-thick gold diaphragm and separate power supply. It features 20Hz–20kHz specs and can take up to 131dB SPL, which is a lot for a tube mic. While it may not be the best call by itself, it would make a nice mic to put back around 3–4 feet for some additional room sound.
$1,699 street
audio-technica.com
Coles 4038
The 4038 is a studio ribbon mic designed by the BBC for broadcasting and recording. It’s bidirectional (figure-8) with a frequency response of 30Hz–15kHz and can take up to 125dB SPL—although we had to move this back to 11 inches for breakup factor. Another classic ribbon sound with the softened highs and warm overall tone, there’s no denying this one.
$1,438 street
Audio-Technica AT4047/SV
This good-looking condenser mic has a wide frequency response of 20Hz–18kHz and the ability to take up to 159dB SPL with the 10dB pad in. There’s a switchable 80Hz hi-pass filter as well, and it features a gold plated dualdiaphragm capsule design. It captured both crisp highs and a well-rounded bottom.
$699 street
audio-technica.com
AKG C414
Wow, another classic. The 414 has five switchable polar patterns (omni, wide cardioid, cardioid, hyper cardioid, figure-8) and a large, 1-inch diaphragm. It’s got 20Hz–20kHz frequency response and a max SPL of up to 158 with -18dB of attenuation switched in. We set it to cardioid, no pad. This mic cuts through a mix well and has lots of attitude.
$1,155 street
akg.com
Electro-Voice RE20
Often referred to as the “donkey dick” mic, this large diaphragm dynamic cardioid monster routinely seen and heard on radio/TV broadcasts has a frequency response of 45Hz–18kHz. Commonly used in guitar session work, it makes a great complement to other mics, such as the 57. We used a PL15, which is basically the same model. It’s got great low end in both the clean and distorted parts… smooth upper mids and not too much high end.
$449 street
electrovoice.com
Shure SM7B
This dynamic is often viewed as a radio mic, but it has a smooth sound and 50Hz–20kHz frequency response. There are bass roll-off and mid-range emphasis switches, but we set it flat. With an immediately pleasing sound both clean and distorted, it’s got a bottom-heavy focus that works great alone or in conjunction with a brighter mic—great attitude.
$399 street
shure.com
M-Audio Luna
Now available as the Luna II, this cardioid condenser has a large, solid brass capsule, Class-A electronics and a 10dB pad, which lets it handle up to 140dB SPL. It has a good, full low end and smooth mids, especially on the distorted tracks, and is well balanced.
m-audio.com
Heil PR 40
A dynamic supercardioid mic from Heil Sound, it features a large low-mass aluminum diaphragm, a heavy steel case and a wide frequency response from 28Hz–18kHz. Very nice bottom and high end, almost nondescript in a positive way. It sounds really cool with a Coles 4038, or the like.
$299 street
heilsound.com
DPA 4006
Now labeled under the DPA name, this high-end, phantom-powered omni mic is often used in classical recordings. Its got an extremely linear frequency response from 20Hz–20kHz, and can take up to 143dB max SPL. It sounds quite natural, with non-extended highs and lows that give you back just what you put in front of it.
$2,339 street
dpamicrophones.com
Reslo
A classic English ribbon mic from the early sixties, it’s got a frequency response of 40Hz–15kHz… no wonder it can be heard on some of those classic Beatles recordings. The output sounds like analog tape through an old tube console.
[Updated 12/12/21]
Lutefish, the real-time music collaboration device and platform, is excited to announce a suite of new features designed to simplify setup, streamline collaboration, and offer more flexible subscription options for Lutefish Stream users. These latest updates, Audio Presets, Automatic Session Recall, Improved Scheduling with Contact Visibility, and a new Yearly Subscription Plan, are all about making it easier than ever for musicians to jam together, no matter where they’re based.
Save Time and Stay in the Flow with Audio Presets & Session Recall
Musicians can now save and reuse their exact audio settings, reducing setup time and ensuring every session sounds exactly as they want.
- Automatic Session Recall: When users leave a session, their current audio levels are automatically saved and restored when they rejoin.
- User-Defined Audio Presets: Each user can create and name up to five custom presets, like “Band Practice,” “Studio Mic Setup,” or “Quick Jam,” making it effortless to jump back in with the perfect sound.
“These tools are all about saving time and hassle,” said Patrick Finn, Business Manager at Lutefish. “Musicians want to make music, not spend time rebalancing levels every session. With presets and recall, we’re giving them time back and helping them sound their best, every time.”
Smarter Scheduling and Contact Visibility
The latest update to Lutefish also made it easier to find collaborators and book sessions. Users can now:- View all their contacts at a glance when scheduling a session.
- Instantly identify which contacts own a Lutefish Stream device—so they will always know who’s ready to jam.
Go Yearly and Save 20%
Lutefish now offers a Yearly Subscription Plan, providing users with the same great access as the monthly plan at a 20% discount.
This option is now available within the Lutefish app and web platform, and current monthly users are eligible for a discount with an upgrade to a yearly subscription.
Lutefish’s mission has always been to empower musicians to connect and collaborate without boundaries. With these new updates, Lutefish Stream continues to break down barriers—whether you’re jamming with a friend across town or collaborating with a bandmate 500 miles away.
For more information and to start jamming today, visitlutefish.com.
Empress Effects is proud to announce the release of the Bass ParaEq, a bass-specific parametric EQ pedal.
Building on the success of their acclaimed ParaEq MKII series, which has already gained popularity with bassists, the Bass ParaEq offers the same studio-grade precision but with features tailored for bass instruments.
Basses of all types – including electric and upright basses with active and passive electronics – can benefit from the Bass ParaEq’s tone-sculpting capabilities.
The new pedal follows the success of the Empress Bass Compressor and ParaEq MKII Deluxe, which have become some of the company’s best-reviewed and top-selling products. The Bass Compressor’s popularity confirmed what Empress had long suspected: bassists are eager for tools built with their needs in mind, not just adaptations of guitar gear.
The Bass ParaEq retains the line’s powerful 3-band parametric EQ and studio-style features while introducing a bass-optimized frequency layout, a selectable 10MΩ Hi-Z input for piezo-equipped instruments, a dynamically-adjusted low shelf, and automatic balanced output detection—perfect for live and studio use alike.
The Bass ParaEq also offers an output boost, adjustable by a dedicated top-mounted knob and activated by its own footswitch, capable of delivering up to 30dB of boost. It’s perfect for helping your bass punch through during key moments in live performance.
Whether dialing in clarity for a dense mix or compensating for an unfamiliar venue, the Bass ParaEq offers precise tonal control in a compact, road-ready form. With 27V of internal headroom to prevent clipping from even the hottest active pickups, the Bass ParaEq is the ultimate studio-style EQ designed to travel.
Key features of the Bass ParaEq include:
- Adjustable frequency bands tailored for bass instruments
- Selectable 10MΩ Hi-Z input for upright basses and piezo pickups
- Auto-detecting balanced output for long cable runs and direct recording
- Three sweepable parametric bands with variable Q
- High-pass, low-pass, low shelf, and high shelf filters
- Transparent analog signal path with 27V of internal headroom
- Buffered bypass switching
- Powered by standard 9V external supply, 300mA (no battery compartment)
The Bass ParaEq is now shipping worldwide. It can be purchased from the Empress Effects website for $374 USD and through authorized Empress dealers globally.
Few musical acts did more to put their fame and fortune to good use than punk rock icon Wayne Kramer. Known for his enduring commitment to activism, especially in justice reform, his life story embodies the defiant, DIY ethos of punk, directly inspiring generations of bands and musicians who followed. Now, fans and fellow musicians alike can attempt to emulate Kramer’s incendiary sound with the new, limited-edition pedal.
Designed before his death in February 2024, Wayne Kramer—together with friend Jimi Dunlop (Dunlop CEO) and Daredevil Pedals owner Johnny Wator —the pedal features artwork from artist and activist Shepard Fairey (Obey Clothing founder). A majority of profits from the sale of the pedal goes directly to Kramer’s charity supporting the rehabilitation of incarcerated people of all ages, genders, and backgrounds.
In honor of his close friend, Tom Morello—the innovative guitarist behind Rage Against the Machine, Audioslave, the Nightwatchman, and more—demoed the pedal, showcasing its sound and shining light on Wayne Kramer’s incredible legacy.
Tom Morello Introduces MC5 Wayne Kramer-Inspired Pedal For Charity: MXR Jail Guitar Doors Drive
"What they've tried to bake into the MXR® Jail Guitar Doors Drive distortion pedal is not just Wayne's sound but Wayne's attitude, and the grit and the rawness of Detroit and of the MC5," said Morello, one of Kramer’s best friends, during his demo of the pedal. "This is the guitar pedal that was used on the song 'Heavy Lifting' that I recorded with Wayne for the last MC5 record.
"Named after the late rocker's charity—which provides instruments and art workshops to incarcerated individuals as rehabilitation tools—the MXR® Jail Guitar Doors Drive pedal aims to capture all of the high-voltage energy of Wayne Kramer's sound. It features two uniquely voiced gain circuits cascaded together with a singular pot controlling both the output level of each circuit and the overall saturation level of the distortion.
Music makers looking to capture Kramer’s raw, fiery sound can pick up the new MXR® Jail Guitar Doors Drive pedal, exclusively on Reverb via The Official MXR Jail Guitar Doors Drive Reverb Shop for $199, here: https://reverb.com/shop/the-official-mxr-jail-guitar-doors-reverb-shop.
The veteran Florida-born metalcore outfit proves that you don’t need humbuckers to pull off high gain.
Last August, metalcore giants Poison the Well gave the world a gift: They announced they were working on their first studio album in 15 years. They unleashed the first taste, single “Trembling Level,” back in January, and set off on a spring North American tour during which they played their debut record, The Opposite of December… A Season of Separation, in full every night.
PG’s Perry Bean caught up with guitarists Ryan Primack and Vadim Taver, and bassist Noah Harmon, ahead of the band’s show at Nashville’s Brooklyn Bowl for this new Rig Rundown.
Brought to you by D’Addario.Not-So-Quiet As a Mouse
Primack started his playing career on Telecasters, then switched to Les Pauls, but when his prized LPs were stolen, he jumped back to Teles, and now owns nine of them.
His No. 1 is this white one (left). Seymour Duncan made him a JB Model pickup in a single-coil size for the bridge position, while the neck is a Seymour Duncan Quarter Pound Staggered. He ripped out all the electronics, added a Gibson-style toggle switch, flipped the control plate orientation thanks to an obsession with Danny Gatton, and included just one steel knob to control tone. Primack also installed string trees with foam to control extra noise.
This one has Ernie Ball Papa Het’s Hardwired strings, .011–.050.
Here, Kitty, Kitty
Primack runs both a PRS Archon and a Bad Cat Lynx at the same time, covering both 6L6 and EL34 territories. The Lynx goes into a Friedman 4x12 cab that’s been rebadged in honor of its nickname, “Donkey,” while the Archon, which is like a “refined 5150,” runs through an Orange 4x12.
Ryan Primack’s Pedalboard
Primack’s board sports a Saturnworks True Bypass Multi Looper, plus two Saturnworks boost pedals. The rest includes a Boss TU-3w, DOD Bifet Boost 410, Caroline Electronics Hawaiian Pizza, Fortin ZUUL +, MXR Phase 100, JHS Series 3 Tremolo, Boss DM-2w, DOD Rubberneck, MXR Carbon Copy Deluxe, Walrus Slo, and SolidGoldFX Surf Rider III.
Taver’s Teles
Vadim Taver’s go-to is this cherryburst Fender Telecaster, which he scored in the early 2000s and has been upgraded to Seymour Duncan pickups on Primack’s recommendation. His white Balaguer T-style has been treated to the same upgrade. The Balaguer is tuned to drop C, and the Fender stays in D standard. Both have D’Addario strings, with a slightly heavier gauge on the Balaguer.
Dual-Channel Chugger
Taver loves his 2-channel Orange Rockerverb 100s, one of which lives in a case made right in Nashville.
Vadim Taver’s Pedalboard
Taver’s board includes an MXR Joshua, MXR Carbon Copy Deluxe, Empress Tremolo, Walrus ARP-87, Old Blood Noise Endeavors Reflector, MXR Phase 90, Boss CE-2w, and Sonic Research Turbo Tuner ST-200, all powered by a Voodoo Lab Pedal Power 2 Plus.
Big Duff
Harmon’s favorite these days is this Fender Duff McKagan Deluxe Precision Bass, which he’s outfitted with a Leo Quan Badass bridge. His backup is a Mexico-made Fender Classic Series ’70s Jazz Bass. This one also sports Primack-picked pickups.
Rental Rockers
Harmon rented this Orange AD200B MK III head, which runs through a 1x15 cab on top and a 4x10 on the bottom.
Noah Harmon’s Pedalboard
Harmon’s board carries a Boss TU-2, Boss ODB-3, MXR Dyna Comp, Darkglass Electronics Vintage Ultra, and a Voodoo Lab Pedal Power 2 Plus. His signal from the Vintage Ultra runs right to the front-of-house, and Harmon estimates that that signal accounts for about half of what people hear on any given night.