
A view of the mic closet at Nashville’s County Q studio.
Compare notes with Nashville producer-engineer Mike Purcell, who runs down the essentials of a pro-level home-studio mic collection.
A well-rounded mic closet could take a lifetime to build. I’m constantly trying different things, but there’s always a core set of mics I come back to because they’re reliable and provide good results. Many of these mics work on a wide range of instruments. By knowing my mics, I can make a choice that’s going to enhance the sound of an instrument—especially guitar.
In this story, I’ve listed several options for each mic type covering a range of prices from low to high. A higher cost usually indicates that the quality of components and workmanship are better, leading to a more consistent product. Lower cost generally means quality control isn’t as strict and that mics may differ more from their published specs.
You’ve probably heard this before, but the three main types of mics are dynamic (or moving coil), condenser (or capacitor), and ribbon mics. Let’s work our way through each category.
Dynamic Mics
Dynamic mics are composed of a voice coil suspended in a magnet. Incoming sound moves the voice coil within the magnetic field and a current is created. This is passed through a transformer to step up the voltage, and then sent to a mic preamp.
Dynamic mics are the mainstay of live sound because of their durability and ability to be used on loud sound sources without overloading. These are desirable characteristics in the studio when we’ve got to place mics close to a flailing drummer or mike up a Marshall Super Lead 100 full stack.
Dynamic mics exhibit the following characteristics:
- They are less sensitive to transients and high frequencies (7k and up.) They capture these frequencies, but at a lower level than a condenser.
- They color the sound in the midrange between 3-5k, adding a slight bump in this area.
- On loud sound sources, they exhibit a type of mild compression or soft clipping, useful on amps, drums, and vocals.
- They are cardioid, or unidirectional, and are the most sensitive in the front with maximum rejection off the back. (There are divisions of cardioid: hyper, super, etc. In all cases, they are most sensitive at the front, with rejection off the back or sides.)
- They exhibit a proximity effect. As directional mics are placed closer to a sound source, they pick up more low end, 100 Hz and below. Dynamic mics are designed to use the proximity effect, so as they move farther from a sound source, they will sound thinner.
“Dynamic mics are the mainstay of live sound because of their durability and ability to be used on loud sound sources without overloading.”
Even though dynamics all exhibit these same general characteristics, each mic will color the sound differently. Some dynamic mics work better on drums. They have an increased low-frequency response, a dip in the lower mids, and a bump in the presence range—essentially an EQ curve that sounds good on bass drums and toms. Others may have a more pronounced bump in the upper mids, making them a great choice for guitar amplifiers. While dynamic mics are typically used for the close miking of drums and guitar amplifiers, they are also well-suited to some vocalists.
A well-rounded mic closet in a home studio that cuts four- or five-piece bands would have at least 8 to 10 dynamics. Modern production dynamic mics top out around $600, and most are under $250.
Dynamics mics to consider:
- Shure SM57 ($99 street): The most common mic in the world. It’s cheap, incredibly durable, and sonically consistent from mic to mic. It can take the highest sound pressure level (SPL) you can throw at it and work on any instrument in a pinch. It’s often used for snare drums or guitar amps. Many of Tom Petty’s vocals were recorded with an SM57.
- Shure SM58 ($99 street): The big brother to the SM57. It has a built-in pop filter/windscreen and a slightly different low-end response. There are hundreds of cheap knockoffs of the Shure SM57 and SM58. Stick with the originals and you’ll be much happier over the long run.
- Sennheiser e 609 ($99 street): An inexpensive supercardioid mic. The supercardioid pattern indicates it is much more directional than a cardioid. This can be useful when miking a snare drum, to reject sound off the sides of the mic. The e 609 also has a slightly less harsh frequency response, so can be useful on edgy or bright guitars.
- Shure Beta 52A ($199 street), Audix D6 ($199 street), AKG D112 ($229 street): These are a newer generation of dynamic mics that are designed for bass drums. Plus, they work well on toms—although Audix also makes the D4 and D2, which are tailored towards smaller drum frequencies (rack tom, floor tom). And they work well on bass amplifiers.
- Sennheiser MD 421-II ($399 street): Excellent kick and tom microphone. The frequency response of the 421 works well on drums. It’s also commonly used on guitar amps and vocals.
- Shure SM7B ($399 street): Another variation using the SM57/58 diaphragm, this mic has electronics that allow you to tailor its frequency response. The SM7 is often used in broadcast and is a go-to choice for vocals by rap and metal artists.
Side note: Many manufacturers offer a drum-mic package—a great solution if you’re starting out. These usually include several dynamics for the close mics and a few condensers for the overheads and/or hi-hat. Plus, these mics can also be used for recording other instruments.
Here are a few examples of drum packages:
- Audix FP7 ($399 street): A seven-piece mic kit, with five dynamics and two condensers. Audix also offers larger drum packages.
- Avantone PRO CDMK-8 ($899 street): This eight-piece kit includes five dynamics and three condensers.
- AKG Drum Set Premium ($2,329 street): Another eight-piece set, with five dynamics and three condensers.
Condenser Mics
Condenser mics consist of a thin, charged diaphragm suspended over a metal plate. As sounds strikes the diaphragm, it moves and causes electrons to flow through the plate. This signal is amplified by internal electronics and passed through a transformer or field-effect transistor (FET) and is sent to a mic preamp.
Condenser mics exhibit these characteristics:
- They are active devices that require a power source, most commonly provided by +48V Phantom Power.
- Some are capable of multiple polar pickup patterns: cardioid, omnidirectional, figure eight, and everything in between.
- They may include a passive attenuation device (PAD), a switchable attenuator that prevents overload when the mic is used on loud sound sources.
- They may include a switchable high-pass filter (HPF), used to roll off unwanted low-end frequencies.
- They are the most sensitive mics, making them ideal for recording quiet instruments.
- They have the widest frequency response and are good at capturing frequencies across the audible spectrum.
- They color sound less than other mics and are good when you want to accurately capture the timbre of an instrument.
Condenser mics are divided into two categories: small diaphragm condensers (SDC) and large diaphragm condensers (LDC). SDCs have a diaphragm of less than 1" and tend to be more responsive to transients and high frequencies. Their off-axis response is also more even.
LDCs have a 1" or greater diaphragm. They sound fuller, but off-axis mic response can be uneven. LDCs, because of their overall size, can be harder to position in tight miking situations.
“Because of their sensitivity and wide frequency response, condenser mics are used for drum overheads and ambience, acoustic stringed instruments, piano, ensembles, amplifiers, and vocals.”
Matched microphone sets require that the frequency response and sensitivity of the two microphones are very similar. This allows them to record a balanced stereo image. So, a well-rounded mic closet will have a matched set of SDCs and LDCs, and a few assorted condensers for other purposes.
SDCs to consider:
- Rode NT5 ($219 single/$429 pair street): Rode is an Australian manufacturer that makes quality products at affordable prices. I’ve been impressed with all their equipment, and the NT5 is no exception.
- Shure SM81 ($399 street): A good, durable utility mic. Inexpensive. Not as open sounding as other SDCs. I use these for snare bottoms and hi-hats. They have a PAD and HPF.
- Warm Audio WA84 ($399 single/$749 pair street): Warm Audio is a relative newcomer to the pro audio world. They’ve been making reproductions of classic gear and offering them at lower prices. In general, I’ve been impressed with the quality of their products. These PAD-equipped mics are their version of the KM-184, at half the cost.
- AKG C451 B ($639 single/$1,395 pair street): Very responsive to transients and can take high SPL. These PAD and HPF mics yield an edgier sound. I love these on mandolin or banjo.
- Miktek C5 ($699 /$1,399 pair street): These mics include a switchable omni capsule, allowing for cardioid and omnidirectional use for spaced pair miking.
- Neumann KM184 ($849 single/$1,595 pair street): Smooth sounding all-around mic with an articulate and defined high-frequency response. One of my favorite go-to mics when I need a stereo recording of an instrument.
LDCs to consider:
With LDCs, manufacturers have families of mics that use the same basic components, but the higher-end mics will offer pattern selection or other features. Within the family, the sound will be similar. Examples are the AKG C214 and C414, and the Shure KSM32 and KSM44.
- Rode NT1000 ($329 street): I am a huge fan of Rode, and the NT1000 routinely beats out more expensive mics for vocals. This cardioid mic is solidly built and big sounding without harshness..
- AKG C214 ($465 street): The little brother to the AKG C414, this cardioid-only example with a PAD and HPF exhibits the same general frequency response, but it doesn’t have all the features of the 414.
- Audio Technica AT4033A ($399 street): One of my favorite inexpensive mics, the 4033 has a pleasant defined midrange and clarity that brings instruments through the mix. These may not be good when trying to capture extended low frequencies. Audio-Technica calls this cardioid mic a medium-diaphragm condenser.
- Miktek C1 and C7e ($599 and $899 street): Miktek is a Nashville-based manufacturer that has developed a line of mics that perform far outside their price class. The C1 has a PAD, HPF, and is cardioid only, while the C7e is multipattern.
- Neumann TLM 103 ($1,195 street): The TLM 103 is a smaller footprint package that utilizes Neumann’s classic U 87 capsule and transformer-less circuitry at a more affordable price. These sound great on vocals and acoustic stringed instruments, if you’re looking for a bigger sound.
- AKG C414 ($1,279 street): The 414 is another industry standard found in many studios. Based on the classic AKG CK12 capsule, the 414 has a wide frequency response. It is bright and present and can sound amazing on some singers and overly bright on others. It works well on pianos and acoustic guitars where you need a sheen on them.
- Neumann U 87 Ai ($3,695 street): The U 87 is a flagship standard that you can find in almost any studio. Multipattern select, HPF and PAD equipped, it’s got a fat low end, smooth high frequencies without harshness, and a thick, musical midrange. An incredibly flexible mic with excellent fidelity, it’s got a price tag to match its functionality. I’ve used these on toms for a huge sound, but you have to really trust the drummer if you’re putting this mic in range of their sticks
Ribbon Mics
Ribbon mics function by suspending a very thin conductive metal strip between two magnets. Sound waves strike the metal strip, causing it to vibrate. The vibration in the magnetic field creates a current in the magnets. This is sent through a transformer, and then the signal is sent to a mic preamp.
“Never run +48V phantom power to a ribbon mic. While most modern ribbons are phantom safe, it can destroy vintage ribbon mics.”
A good mic closet should have several ribbon mics, and possibly more depending on the style of production. Ribbon mics have seen a resurgence over the past 20 years and there is a wide variety available, ranging from $200 to $1,500 and more. Ribbons are used on guitar amps, as drum overhead or room mics, and on horns, acoustic guitars, percussion, and vocals.
Ribbon mics exhibit these characteristics:
- The thin ribbon allows them to be very sensitive to transients.
- They color the sound. They are warm sounding and add character.
- They are the least sensitive type of mic and ill-suited for quiet sound sources.
- They’re very fragile. A puff of wind (or the air coming out of a kick drum) can damage the mic.
- They are bi-directional/figure eight. They pick up sound from the front and back of the mic at the same level. Exceptions exist, like the Beyerdynamic M 160.
- Caution: Never run +48V phantom power to a ribbon mic. While most modern ribbons are phantom safe, it can destroy vintage ribbon mics. (Once again, there are exceptions. Active ribbon mics, like the AEA N22 Nuvo, exist. These do have internal amplification similar to a condenser and require phantom power.)
Ribbon mics to consider:
- Pinnacle Microphones Fat Top ($229/$519 pair street): The Fat Top is a current iteration of the original Cascade Fat Head. I’ve used Fat Heads for years. They’re wonderful on guitar amps and percussion.
- Stager SR-66/SR-2N ($699/$649 street): Stager Microphones is a small boutique operation in Nashville. They use neodymium magnets in these models, for increased magnetism in a lighter package. The transformers are hand-wound and designed to get the best transfer of sound from ribbon to mic preamp. The SR-66 is a long-ribbon package, offering a flatter frequency response. The SR-2N is a midrange-forward short-ribbon design.
- Coles Electroacoustics 4038 ($1,485 street): The Coles 4038 is designed by the British Broadcasting Corporation in the 1950s and the tech specs have never changed. A lot of work went into engineering this mic. It has a flat frequency response up to 15k and is very responsive to transients.
- Royer R-121 ($1,499 street): Royer Labs is one of the best-known manufacturers of ribbon mics. They’ve pioneered innovations in ribbon mic technology that allow them to be used on very loud sound sources without damage to the microphone. The R-121 is one of the most popular mics in existence and exhibits all the classic characteristics of a ribbon mic.
What about tube microphones?
Tube mics are a subset of condenser mics. Up until the 1960s, condensers used a tube for the amplification of the low-level diaphragm signal. Tubes sound nice, but have a lot of issues: heat, high power requirements, and they can suffer from microphonics. In the ’60s, a solid-state replacement for the tube was created: the FET, or field effect transistor. The FET emulates tube characteristics and has two benefits: smaller size and reduced power requirements. The first solid-state condenser mic designs used the same circuit except for the FET substitution, but they sounded different, crisper. They had lost the tube character.
Tube mics are revered for their warmth, wide frequency response, and pleasing sound. They are most commonly used for vocals, but I’ve used them for every instrument. There’s a robust market for inexpensive tube mic modification. Sometimes it’s as easy as swapping a tube, while others do capsule and component level changes. These mods can greatly enhance the sound of an inexpensive tube mic. A good mic closet should have at least one curated tube mic. They start at about $499 and can range upwards of $30,000.
Some manufacturers with tube mics in the below-$1,000 price range include Avantone, Warm Audio, Golden Age, and Lauten Audio. My recommendation is to audition several and find the one that will have the broadest application for your recording situation. They won’t sound exactly like their pricier counterparts, but they’ll give you a flavor in your mic closet that’s only possible with a tube microphone.
Tube mics to consider:
- Mojave MA-300SN ($1,399): Mojave was created by David Royer of Royer Labs. They use quality components for mics that meet exacting standards. The 300SN is a tube large-diaphragm condenser mic. It features a continuously variable pattern select, which ranges from omni to figure eight. The MA300SN has a warm low end with an open top.
- Miktek CV4 ($1,699 street): Miktek’s line of hand-built mics includes this large diaphragm condenser with nine polar patterns. I’ve used these on vocals and stringed instruments with great success.
- Peluso 22 47 SE ($2,149 street): Peluso Microphone Lab is a boutique company that hand builds each mic. The 22 47 is a reproduction of the venerable Neumann U 47. The 22 47 is a great choice for vocals and acoustic instruments, and I find myself using less EQ when recording with this mic. Their interpretations of other classic mics are also available.
Photo by Nick Sonsini
- Telefunken ELA M 251 (repro: $10,996/vintage: $25,000-plus street): Around 3,700 units of the original 251 were manufactured from 1960 to ’65, but a modern reproduction is available. It has an open top end without harshness, a smooth, rich midrange, and low-end warmth with punchiness. It’s an excellent vocal mic and excels on harmonically rich instruments.
Now, Go Forth and Record
You’ve got to start somewhere when building your mic closet. If you’re not tracking full bands, I’d recommend starting with a couple dynamics (like the SM57) and a set of LDCs. With these mics, you’ll be able to cover basic overdub sessions. From there, borrow mics from friends, explore the world of ribbon and tube mic sounds, and discover what works best for your home studio.
What About DIs?
Direct boxes, or DIs, are an integral part of any studio. They are used to connect (Hi-Z) instruments with low-impedance (Lo-Z) microphone preamps. Hi-Z devices, such as guitars and basses, have 1/4" outputs. The DI provides a 1/4" input to connect to your guitar and an XLR output which connects to a preamp. DIs also have a 1/4" output jack. This is used to pass the signal through the DI and connect to an amplifier. Often, a bass or guitar is recorded to two tracks—one signal from the DI and the other from an amplifier.
There are two types of DIs: passive and active. Passive devices have of an internal transformer that changes the impedance of the signal. Active DIs require a power source for their internal electronics and will have less signal degradation than a passive device. A good home studio should have at least one active DI and two passive DIs.
Modern DAW interfaces usually have built-in Hi-Z inputs via 1/4" jacks that allow you to connect directly to your interface. These negate the need for a DI.
Here are several DI boxes to consider:
- Radial StageBug S-B2 ($89 street): Radial is well known for their technology in direct box design. This is a passive DI with a small footprint.
- Radial Pro48 ($129 street): These active devices are full-range DIs with a bandwidth of 20 Hz to 20k.
- Rupert Neve Designs RNDI-1($299 street): Like most Neve designs, this active device is engineered for the highest fidelity audio and sounds great.
Digital Modeling Mics
Digital microphone modeling systems are a relatively new development. They combine a specially designed microphone with modeling software that allows you to record audio that sounds as if you had used a different microphone. The software models a variety of classic or vintage mics. The two frontrunners in this new tech are the Slate Digital VMS Virtual Microphone System and Universal Audio’s Sphere L22 Microphone Modeling System (which was developed in conjunction with Townsend Labs).
They use a sonically transparent microphone designed to interface with their modeling software. The signal is passed from the mic through a neutral mic pre (one that doesn’t color the sound too much) to your DAW input. The plugin is applied to the audio and an output mic model is selected. The result sounds as if it had been recorded with the selected mic.
Slate and UA accomplish this by testing and measuring a microphone’s behavior and mapping that behavior out in software. The software knows the characteristics of the recording mic and processes the audio, applying the differences to the signal. The recorded signal now sounds as if it was recorded with a $20,000 Neumann U 67 (or whichever mic you’ve selected).
The benefit of these systems is that it is non-destructive. Just like amp modeling plugins, there is a dry sound recorded in your DAW, and the processing is applied with a plugin. You have the ability to modify it throughout the recording process, finding the sound that works with your final production.
These systems offer a huge range of sounds and offer mic selections that would not be available in your average home studio. And each system offers a selection of recognized mic models with an established track record.
The lowdown:
• Slate Digital VMS Virtual Microphone System (mic and software $499 street): This system’s ML-2 is a small diaphragm mic. Once recorded, sound is processed via the VMS plugin (compatible with AAX, VST2, VST3, and AU formats). The VMS software includes 13 mic models, ranging from the AKG C12 to the Shure SM7B. Two add-on mic bundles are available for purchase from Slate: Blackbird Mics ($199 street), featuring five mics from Nashville’s Blackbird Studio, and Classic Tubes ($299 street), featuring five modeled mics.
• Universal Audio Sphere L22 Microphone Modeling System ($1,199 to $1,499 street): UA’s Sphere L22 was developed in conjunction with Townsend Labs. The Sphere software works the same as VMS, tuned for the provided mic and offering 34 output mic models.
The Sphere system uses a dual-capsule mic. This allows the software to take the signal from both capsules and create a 3D sonic picture of the modeled microphone. In theory, this should offer off-axis behavior similar to the originals. The mic can use both capsules to create a stereo recording, too.
The software is available in UAD, AAX, VST2, VST3, and AU formats. It offers more tweakable parameters than the VMS. So, if you’re a knob twister and like to fine-tune your sounds, the Sphere is a good choice. The additional controls come with a higher price tag.
- Tone Tips: Modelers vs. Traditional Rigs, Part 2 ›
- Amp Mic’ing vs. Impulse Responses ›
- The Recording Guitarist: Mic Makes Right ›
- Color Coding Sessions Can Save Your Butt - Premier Guitar ›
- How to Get More Out of Your Mics with Modelers - Premier Guitar ›
Onstage, Tommy Emmanuel executes a move that is not from the playbook of his hero, Chet Atkins.
Recorded live at the Sydney Opera House, the Australian guitarist’s new album reminds listeners that his fingerpicking is in a stratum all its own. His approach to arranging only amplifies that distinction—and his devotion to Chet Atkins.
Australian fingerpicking virtuoso Tommy Emmanuel is turning 70 this year. He’s been performing since he was 6, and for every solo show he’s played, he’s never used a setlist.
“My biggest decision every day on tour is, ‘What do I want to start with? How do I want to come out of the gate?’” Emmanuel explains to me over a video call. “A good opener has to have everything. It has to be full of surprise, it has to have lots of good ideas, lots of light and shade, and then, hit it again,” he says, illustrating each phrase with his hands and ending with a punch.“You lift off straightaway with the first song, you get airborne, you start reaching, and then it’s time to level out and take people on a journey.”
In May 2023, Emmanuel played two shows at the Sydney Opera House, the best performances from which have been combined on his new release, Live at the Sydney Opera House. The venue’s Concert Hall, which has a capacity of 2,679, is a familiar room for Emmanuel, but I think at this point in his career he wouldn’t bring a setlist if he was playing Wembley Stadium. On the recording, Emmanuel’s mind-blowingly dexterous chops, distinctive attack and flair, and knack for culturally resonant compositions are on full display. His opening song for the shows? An original, “Countrywide,” with a segue into Chet Atkins’ “El Vaquero.”
“When I was going to high school in the ’60s, I heard ‘El Vaquero’ on Chet Atkins’ record, [1964’s My Favorite Guitars],” Emmanuel shares. “And when I wrote ‘Countrywide’ in around ’76 or ’77, I suddenly realized, ‘Ah! It’s a bit like “El Vaquero!”’ So I then worked out ‘El Vaquero’ as a solo piece, because it wasn’t recorded like that [by Atkins originally].
“The co-writer of ‘El Vaquero’ is Wayne Moss, who’s a famous Nashville session guy who played ‘da da da’ [sings the guitar riff from Roy Orbison’s ‘Pretty Woman’]. And he played on a lot of Chet’s records as a rhythm guy. So once when I played ‘El Vaquero’ live, Wayne Moss came up to me and said, ‘You know, you did my part and Chet’s at the same time. That’s not fair!’” Emmanuel says, laughing.
Atkins is the reason Emmanuel got into performing. His mother had been teaching him rhythm guitar for a couple years when he heard Atkins on the radio and, at 6, was able to immediately mimic his fingerpicking technique. His father recognized Emmanuel’s prodigious talent and got him on the road that year, which kicked off his professional career. He says, “By the time I was 6, I was already sleep-deprived, working too hard, and being forced to be educated. Because all I was interested in was playing music.”
Emmanuel talks about Atkins as if the way he viewed him as a boy hasn’t changed. The title Atkins bestowed upon him, C.G.P. (Certified Guitar Player), appears on Emmanuel’s album covers, in his record label (C.G.P. Sounds), and is inlaid at the 12th fret on his Maton Custom Shop TE Personal signature acoustic. (Atkins named only five guitarists C.G.P.s. The others are John Knowles, Steve Wariner, Jerry Reed, and Atkins himself.) For Emmanuel, even today most roads lead to Atkins.
When I ask Emmanuel about his approach to arranging for solo acoustic guitar, he says, “It was really hit home for me by my hero, Chet Atkins, when I read an interview with him a long time ago and he said, ‘Make your arrangement interesting.’ And I thought, ‘Wow!’ Because I was so keen to be true to the composer and play the song as everyone knows it. But then again, I’m recreating it like everyone else has, and I might as well get in line with the rest of them and jump off the cliff into nowhere. So it struck me: ‘How can I make my arrangements interesting?’ Well, make them full of surprises.”
When Emmanuel was invited to contribute to 2015’s Burt Bacharach: This Guitar’s in Love with You, featuring acoustic-guitar tributes to Bacharach’s classic compositions by various artists, Emmanuel expresses that nobody wanted to take “(They Long to Be) Close to You,” due to its “syrupy” nature. But for Emmanuel, this presented an entertaining challenge.
He explains, “I thought, ‘Okay, how can I reboot “Close to You?’ So even the most jaded listener will say, ‘Holy fuck—I didn’t expect that! Wow, I really like that; that is a good melody!’ So I found a good key to play the song in, which allowed me to get some open notes that sustain while I move the chords. Then what I did is, in every phrase, I made the chord unresolve, then resolve.
Tommy Emmanuel's Gear
“I’m writing music for the film that’s in my head,” Emmanuel says. “So, I don’t think, ‘I’m just the guitar,’ ever.”
Photo by Simone Cecchetti
Guitars
- Three Maton Custom Shop TE Personals, each with an AP5 PRO pickup system
Amps
- Udo Roesner Da Capo 75
Effects
- AER Pocket Tools preamp
Strings & Picks
- Martin TE Signature Phosphor Bronze (.012–.054)
- Martin SP strings
- Ernie Ball Paradigm strings
- D’Andrea Pro Plec 1.5 mm
- Dunlop medium thumbpicks
“And then to really put the nail in the coffin, at the end, ‘Close to you’ [sings melody]. I finished on a major 9 chord which had that note in it, but it wasn’t the key the song was in, which is a typical Stevie Wonder trick. All the tricks I know, the wonderful ideas that I’ve stolen, are from Michael Jackson, Stevie Wonder, Lionel Richie, James Taylor, Carole King, Neil Diamond. All of the people who wrote really incredibly great pop songs and R&B music—I stole every idea I could, and I tried to make my little two-and-a -half minutes as interesting and entertaining as possible. Because entertainment equals: Surprise me.”
I share with Emmanuel that the performances on Live at the Sydney Opera House, which include his popular “Beatles Medley,” reminded me of another possible arrangement trick. In Harpo Marx’s autobiography, Harpo Speaks, I preface, Marx writes of a lesson he learned as a performer—to “answer the audience’s questions.” (Emmanuel says he’s a big fan of the book and read it in the early ’70s.) That happened for me while listening to the medley, when, after sampling melodies from “She’s a Woman” and “Please Please Me,” Emmanuel suddenly lands on “While My Guitar Gently Weeps.”
I say, “I’m waiting for something that hits more recognizably to me, and when ‘While My Guitar’ comes in, that’s like answering my question.”
“It’s also Paul and John, Paul and John, George,” Emmanuel replies. “You think, ‘That’s great, that’s great pop music,’ then, ‘Wow! Look at the depth of this.’”Often Emmanuel’s flights on his acoustic guitar are seemingly superhuman—as well as supremely entertaining.
Photo by Ekaterina Gorbacheva
A trick I like to employ as a writer, I say to Emmanuel, is that when I’m describing something, I’ll provide the reader with just enough context so that they can complete the thought on their own.
“You can do that musically as well,” says Emmanuel. He explains how, in his arrangement of “What a Wonderful World,” he’ll play only the vocal melody. “When people are asking me at a workshop, ‘How come you don’t put chords behind that part?’ I say, ‘I’m drawing the melody and you’re putting in all the background in your head. I don’t need to tell you what the chords are. You already know what the chords are.’”
“Wayne Moss came up to me and said, ‘You know, you did my part and Chet’s at the same time. That’s not fair!’”
Another track featured on Live at the Sydney Opera House is a cover of Paul Simon’s “American Tune” (which Emmanuel then jumps into an adaptation of the Australian bush ballad, “Waltzing Matilda”). It’s been a while since I really spent time with There GoesRhymin’ Simon (on which “American Tune” was first released), and yet it sounded so familiar to me. A little digging revealed that its melody is based on the 17th-century Christian hymn, “O Sacred Head, Now Wounded,” which was arranged and repurposed by Bach in a few of the composer’s works. The cross-chronological and genre-lackadaisical intersections that come up in popular music sometimes is fascinating.
“I think the principle right there,” Emmanuel muses, “is people like Bach and Beethoven and Mozart found the right language to touch the heart of a human being through their ears and through their senses ... that really did something to them deep in their soul. They found a way with the right chords and the right notes, somehow. It could be as primitive as that.
Tommy Emmanuel has been on the road as a performing guitarist for 64 years. Eat your heart out, Bob Dylan.
Photo by Jan Anderson
“It’s like when you’re a young composer and someone tells you, ‘Have a listen to Elton John’s “Candle in the Wind,”’ he continues. “‘Listen to how those notes work with those chords.’ And every time you hear it, you go, ‘Why does it touch me like that? Why do I feel this way when I hear those chords—those notes against those chords?’ I say, it’s just human nature. Then you wanna go, ‘How can I do that!’” he concludes with a grin.
“You draw from such a variety of genres in your arrangements,” I posit. “Do you try to lean into the side of converting those songs to solo acoustic guitar, or the side of bridging the genre’s culture to that of your audience?”
“I stole every idea I could, and I tried to make my little two-and-a-half minutes as interesting and entertaining as possible. Because entertainment equals: Surprise me.”
“If I was a method actor,” Emmanuel explains, “what I’m doing is—I’m writing music for the film that’s in my head. So, I don’t think, ‘I’m just the guitar,’ ever. I always think it has to have that kind of orchestral, not grandeur, but … palette to it. Because of the influence of Stevie Wonder, Billy Joel, and Elton John, especially—the piano guys—I try to use piano ideas, like putting the third in the low bass a lot, because guitar players don’t necessarily do that. And I try to always do something that makes what I do different.
“I want to be different and recognizable,” he continues. “I remember when people talked about how some players—you just hear one note and you go, ‘Oh, that’s Chet Atkins.’ And it hit me like a train, the reason why a guy like Hank Marvin, the lead guitar player from the Shadows.... I can tell you: He had a tone that I hear in other players now. Everyone copied him—they just don’t know it—including Mark Knopfler, Eric Clapton, Jimmy Page, all those people. I got him up to play with me a few times when he moved to Australia, and even playing acoustic, he still had that sound. I don’t know how he did it, but it was him. He invented himself.”
YouTube It
Emmanuel performs his arrangement of “What a Wonderful World,” illustrating how omitting a harmonic backdrop can have a more powerful effect, especially when playing such a well-known melody.
Our columnist has journeyed through blizzards and hurricanes to scoop up rare, weird guitars, like this axe of unknown origin.
Collecting rare classic guitars isn’t for the faint of heart—a reality confirmed by the case of this Japanese axe of unknown provenance.
If you’ve been reading this column regularly, you’ll know that my kids are getting older and gearing up for life after high school. Cars, insurance, tuition, and independence are really giving me agita these days! As a result, I’ve been slowly selling off my large collection of guitars, amps, and effects. When I’m looking for things to sell, I often find stuff I forgot I had—it’s crazy town! Finding rare gear was such a passion of mine for so many years. I braved snowstorms, sketchy situations, shady characters, slimy shop owners, and even hurricane Sandy! If you think about it, it’s sort of easy to buy gear. All you have to do is be patient and search. Even payments nowadays are simple. I mean, when I got my first credit card…. Forget about it!
Now, selling, which is what I mainly do now, is a different story. Packing, shipping, and taking photos is time consuming. And man, potential buyers can be really exhausting. I’ve learned that shipping costs are way higher, but buyers are still the same. You have the happy buyer, the tire kicker, the endless questioner, the ghoster, and the grump. Sometimes there are even combinations of the above. It’s an interesting lesson in human psychology, if you’re so inclined. For me, vintage guitars are like vintage cars and have some quirks that a modern player might not appreciate. Like, can you play around buzzing or dead frets? How about really tiny frets? Or humps and bumps on a fretboard? What about controlling high feedback and squealing pickups by keeping your fingers on the metal parts of the guitar? Not everyone can be like Jack White, fighting his old, red, Valco-made fiberglass Airline. It had one working pickup and original frets! I guess my point is: Buyer beware!
“They all sound great—all made from the same type of wood and all wired similarly—but since real quality control didn’t really exist at that time, the fate of guitars was left up to chance.”
Take, for instance, the crazy-cool guitar presented here. It’s a total unknown as far as the maker goes, but it is Japanese and from the 1960s. I’ve had a few similar models and they all feature metal pickguards and interesting designs. I’ve also seen this same guitar with four pickups, which is a rare find. But here’s the rub: Every one of the guitars I’ve had from the unknown maker were all a bit different as far as playability. They all sound great—all made from the same type of wood and all wired similarly—but since real quality control didn’t exist at that time, the final state of guitars was left up to chance. Like, what if the person carving necks had a hangover that day? Or had a fight that morning? Seriously, each one of these guitars is like a fingerprint. It’s not like today where almost every guitar has a similar feel. It’s like the rare Teisco T-60, one of Glen Campbell’s favorite guitars. I have three, and one has a deep V-shaped neck, and the other two are more rounded and slim. Same guitars, all built in 1960 by just a few Teisco employees that worked there at the time.
When I got this guitar, I expected all the usual things, like a neck shim (to get a better break-over string angle), rewire, possible refret, neck planing, and other usual stuff that I or my great tech Dave D’Amelio have to deal with. Sometimes Dave dreads seeing me show up with problems I can’t handle, but just like a good mechanic, a good tech is hard to come by when it comes to vintage gear. Recently, I sold a guitar that I set up and Dave spent a few more hours getting it playable. When it arrived at the buyer’s home, he sent me an email saying the guitar wasn’t playable and the pickups kept cutting out. He took the guitar to his tech who also said the guitar was unplayable. So what can you do? Every sale has different circumstances.
Anyway, I still have this guitar and still enjoy playing it, but it does fight me a little, and that’s fine with me. The pickup switches get finicky and the volume and tone knobs have to be rolled back and forth to work out the dust, but it simply sounds great! It’s as unique as a snowflake—kinda like the ones I often braved back when I was searching for old gear!
Sleep Token announces their Even In Arcadia Tour, hitting 17 cities across the U.S. this fall. The tour, promoted by AEG Presents, will be their only headline tour of 2025.
Sleep Token returns with Even In Arcadia, their fourth offering and first under RCA Records, set to release on May 9th. This new chapter follows Take Me Back To Eden and continues the unfolding journey, where Sleep Token further intertwines the boundaries of sound and emotion, dissolving into something otherworldly.
As this next chapter commences, the band has unveiled their return to the U.S. with the Even In Arcadia Tour, with stops across 17 cities this fall. Promoted by AEG Presents, the Even In Arcadia Tour will be Sleep Token’s only 2025 headline tour and exclusive to the U.S. All dates are below. Tickets go on sale to the general public on Friday, March 21st at 10 a.m. local time here. Sleep Token will also appear at the Louder Than Life festival on Friday, September 19th.
Sleep Token wants to give fans, not scalpers, the best chance to buy tickets at face value. To make this possible, they have chosen to use Ticketmaster's Face Value Exchange. If fans purchase tickets for a show and can't attend, they'll have the option to resell them to other fans on Ticketmaster at the original price paid. To ensure Face Value Exchange works as intended, Sleep Token has requested all tickets be mobile only and restricted from transfer.
*New York, Illinois, Colorado, and Utah have passed state laws requiring unlimited ticket resale and limiting artists' ability to determine how their tickets are resold. To adhere to local law, tickets in this state will not be restricted from transfer but the artist encourages fans who cannot attend to sell their tickets at the original price paid on Ticketmaster.
For more information, please visit sleep-token.com.
Even In Arcadia Tour Dates:
- September 16, 2025 - Duluth, GA - Gas South Arena
- September 17, 2025 - Orlando, FL - Kia Center
- September 19, 2025 - Louisville, KY - Louder Than Life (Festival)
- September 20, 2025 – Greensboro, NC - First Horizon Coliseum
- September 22, 2025 - Brooklyn, NY - Barclays Center
- September 23, 2025 - Worcester, MA - DCU Center
- September 24, 2025 - Philadelphia, PA - Wells Fargo Center
- September 26, 2025 - Detroit, MI - Little Caesars Arena
- September 27, 2025 - Cleveland, OH - Rocket Arena
- September 28, 2025 - Rosemont, IL - Allstate Arena
- September 30, 2025 - Lincoln, NE - Pinnacle Bank Arena
- October 1, 2025 - Minneapolis, MN - Target Center
- October 3, 2025 - Denver, CO - Ball Arena
- October 5, 2025 - West Valley City, UT - Maverik Center
- October 7, 2025 - Tacoma, WA - Tacoma Dome
- October 8, 2025 - Portland, OR - Moda Center
- October 10, 2025 - Oakland, CA - Oakland Arena
- October 11, 2025 - Los Angeles, CA - Crypto.com Arena
The Rickenbacker 481’s body style was based on the 4001 bass, popularly played by Paul McCartney. Even with that, the guitar was too experimental to reach its full potential.
The body style may have evoked McCartney, but this ahead-of-its-time experiment was a different beast altogether.
In the early days of Beatlemania, John Lennon andGeorge Harrison made stars out of their Rickenbacker guitars: John’s 325, which he acquired in 1960 and used throughout their rise, and George’s 360/12, which brought its inimitable sound to “A Hard Day’s Night” and other early classics.
By the early 1970s, the great interest the lads had sparked in 6- and 12-string Ricks had waned. But thankfully for the company, there was still high demand for yet another Beatles-played instrument: the 4001 bass.
Paul McCartney was gifted a 4001 by Rickenbacker in 1965, which he then used prominently throughout the group’s late-’60s recordings and while leading Wings all through the ’70s. Other rising stars of rock also donned 4000 series models, like Yes’Chris Squire, Pink Floyd’sRoger Waters, the Bee Gees’ Maurice Gibb, Creedence Clearwater Revival’s Stu Cook, and more.
And like that, a new star was born.
So, what’s a guitar company to do when its basses are selling better than its guitars? Voilà: The Rickenbacker 480. Introduced in 1972, it took the 4000-series body shape and created a standard 6-string out of it, using a bolt-on neck for the first time in the brand’s history.
The 481’s slanted frets predate the modern multi-scale phenomenon by decades. The eight-degree tilt of the frets is matched by an eight-degree tilt of the nut, pickups, and bridge.
“It was like a yo-yo at Rickenbacker sometimes,” factory manager Dick Burke says in Rickenbacker Guitars: Out of the Frying Pan Into the Fireglo. “We got quiet in the late ’60s, but when the bass started taking off in the ’70s, we got real busy again, so making a 6-string version of that was logical, I guess.”
The gambit worked, for a time. Sales of the 480 were strong enough at first that, in 1973, a deluxe model was introduced—the 481—and it’s one of these deluxe versions that we’re showcasing here.
“The 481 features slant frets—pointing ever-so-slightly toward the body of the guitar—and the eight-degree tilt of the frets is matched by an eight-degree tilt of the nut, pickups, and bridge.”
Take a close look and you’ll notice that the body shape isn’t the only remarkable feature. The 481 was Rickenbacker’s first production run to feature humbucker pickups. Here, you can see each humbucker’s 12 pole pieces dotting through the chrome cover, a variant casing only available from 1975 to 1976. (Interestingly enough, the pickups had first been developed for the 490, a prototype that never made it to public release, which would’ve allowed players to substitute different pickups by swapping loaded pickguards in and out of the body.)
The new pickups were also treated with novel electronics. The standard 3-way pickup-selector switch is here, but so is a second small switch that reverses the pickups’ phase when engaged.
The inventive minds at Rickenbacker didn’t stop there: The 481 features slant frets—pointing ever-so-slightly toward the body of the guitar—and the eight-degree tilt of the frets is matched by an eight-degree tilt of the nut, pickups, and bridge.
Long before the fanned fret phenomenon caught on in the modern, progressive guitar landscape, Rickenbacker had been toying around with the slant-fret concept. Originally available from 1970 forward as a custom order on other models, slant frets were all but standard on the 481 (only a small minority of straight-fret 481s were built).
The 481 was the deluxe version of the 480, which preceded it and marked the first time the company used a bolt-on neck.
Dick Burke, speaking separately to writer Tony Bacon in an interview published on Reverb, only half-recalls the genesis and doesn’t remember them selling particularly well: “Some musicians said that’s the way when you hold the neck in your left hand—your hand is slanted. So, we put the slanted frets in a few guitars. I don’t know how many, maybe a hundred or two—I don’t recall.”
Even proponents of the 481 do not necessarily sing the praises of the slanted fretboard. Kasabian’s Serge Pizzorno, a 481 superfan, told Rickenbacker Guitars author Martin Kelly, “I don’t just love the 481, it’s part of me.... The 481’s slanted frets have made my fingers crooked for life, but I don’t care, I’ll take that for it’s given me riff after riff after riff."
Initial 480-series sales were promising, but the models never really took off. Though they were built as late as 1984, the slant-fret experiment of the 481 was called off by 1979. And these slanted models have not, in the minds of most players or collectors, become anywhere near as sought-after as the classic 330s and 360s, or, for that matter, the 4001s.
For that reason, 481s—despite their novelty and their lists of firsts for Rickenbacker—can still be found for relatively cheap. Our Vintage Vault pick, which is being sold by the Leicester, England-based Jordan Guitars Ltd, has an asking price of 3,350 British pounds (or about 4,300 U.S. dollars), which is still well under half the going-rate of early 360s, 660s, and other more famous Ricks. Some lucky buyers have even found 481s on Reverb for less than $2,000, which is unheard of for other vintage models.
With its idiosyncratic charms, the 481 remains more within reach than many other guitars of a similar vintage.
Sources: Martin Kelly’s Rickenbacker Guitars: Out of the Frying Pan Into the Fireglo, Tony Bacon’s"Interview: Dick Burke on the Creation of the Rickenbacker 12-String | Bacon’s Archive" on Reverb, Reverb Price Guide sales data.