PRS Pedal Reviews: Horsemeat Transparent Overdrive, Mary Cries Optical Compressor, and Wind Through the Trees Dual Analog Flanger

Paul Reed Smith may hate pedals, but his first foray into the realm delivers nothing but gems.
Inside each box containing a brand new PRS pedal, there’s a little fold-out card with a picture of Paul Reed Smith and a simple caption: “I hate pedals.” It’s not hard to imagine Smith’s indifference to stompboxes. PRS guitars are immaculately executed, ultra-playable instruments that reflect a focus on elemental interactions between fingers, strings, and fretboard. Indeed, for much of Paul Reed Smith’s career, stompboxes were probably held in the same regard as a broken toaster—a needless impediment to the communication of unadulterated tone.
Certainly, there is a visceral thrill to playing a guitar without effects—particularly one as nice as the average PRS. But while that’s true, stompboxes are, to many musicians, equally artful and thrilling vehicles of expression. And more than a few pedals have done their magic with a PRS guitar at the other end of a cable.
PRS’ three debut pedals—an optical compressor, overdrive, and dual flanger—do not feel like willy-nilly concessions to market pressures. In fact, in keeping with PRS tradition and ethos, these pedals seem selected and designed to offer minimal intrusion on the guitar/amp relationship if the player chooses that route. But they also have the bandwidth to be bold and even positively extroverted. Unsurprisingly, they are also built to a very high standard of quality and reflect an intense attention to detail.
PRS Horsemeat, Mary Cries & Wind Through the Trees Demos | First Look
Horsemeat Transparent Overdrive
Horsemeat isn’t a pretty name, but I’m guessing it alludes to making short work—mincemeat, if you will—of the Klon Centaur in a head-to-head battle. It’s hard to know exactly how much inspiration PRS derived from the Klon. PRS emphatically insists that Horsemeat is a very original design. And its circuit board is flipped, making it impossible to determine similarities in topology. It shares at least one important design element with the Klon, in the form of germanium clipping diodes. In a very general sense, germanium diodes tend to contribute soft-edged compression and a high capacity for distortion. But without knowing how other components in the circuit modify the performance of the diodes, you have to rely on your ears. And alongside my favorite Klon clone, Horsemeat sounds like a very different animal indeed.
Next to the Klon clone—which serves here as a familiar baseline rather than a direct comparison—the Horsemeat’s headroom and the leeway to work with it via picking dynamics or the flexible and practical control array is striking.
Though the Horsemeat can get aggressive, moving through the gain control’s range yields many nuanced shades. At maximum gain levels (and with relatively neutral treble, bass, and voice settings), the Horsemeat exhibits a lot of Marshall-plexi-like characteristics. There’s a distinct sense of size, a viscerally satisfying growl to the voice, and lots of top-end response that gives first- and second-string output heat and room to breathe. If you keep the output level at a reasonable setting, the compression in the distortion never feels oppressive or muddy. Instead, the pedal’s natural compression tends to lend cohesion. And even at advanced output level settings (and there is a lot of room to run in that respect), the distortion remains articulate.
“Moving through the gain control’s range really yielded shades of gain rather than heaps of extra crunch and aggression.”
Reducing gain reveals an impressive capacity for touch sensitivity. I can’t remember the last gain device I used that responded so well to variations in fingerpicking intensity. Guitar volume attenuation, too, yields rich and very pretty clean tones. And if you’re frustrated by your single-coil pickup’s tendency to bleed high end with volume reduction, you’ll be tickled by how readily the Horsemeat can replace some of that sparkle.
The bass and treble controls not only have a lot of range, but offer very colorful and varied tones within those areas. You can extract exceptionally bright tones out of the Horsemeat (in fact, extra-trebly settings rather than high-gain sounds struck me as the pedal’s most “extreme” settings). The voice control, which shapes frequency response in the clipping stage, helps you color the pedal’s tones in even more specific ways. Aggressively clockwise settings sound and feel hot and explosive, while the lower-to-middle third of its range have a sweetness that works with the pedal’s intrinsic dynamism to add soulful movement to chord melodies.
The Verdict
It’s hard to imagine an overdrive user that wouldn’t dig working with the Horsemeat. Players that prefer the squish in overdriven Fender tweed circuits might find the output a touch too even across frequencies. But I suspect a lot of players that love the more articulate side of a Marshall’s voice or really obsess over relative transparency will find a soulmate in this fine and varied drive machine.
Mary Cries Optical Compressor
Like the Horsemeat, the Mary Cries comp hints at a possible PRS design team directive: That a guitar’s fundamental voice should always be able to be its best, most exciting self. That’s no surprise for a company whose instruments are typically so rich and sonorous. But like the Universal Audio Teletronix LA-2A optical studio compressor that inspired it, the Mary Cries succeeds so well that it could probably make a busted kazoo shine.
“The Mary Cries could probably make a busted kazoo shine.”
If you ever use a real LA-2A in a studio, you’ll never forget the way it fattens, flatters, and warms a signal. You’ll also be struck by how economical the layout is. Apart from a compression ratio switch, there’s a peak reduction knob (typically just called the compression control) and a make-up gain or output gain control. Even a novice can competently use an LA-2A using ears and intuition.
Building a pedal-sized optical compressor circuit does not automatically make it the equivalent of an LA-2A. That verges on the impossible. But the Mary Cries excels at the same tasks: adding body and excitement to a signal and enabling quick adjustments without overthinking the process. The Mary Cries reduces the control scheme of an LA-2A to just the compression and output gain controls (which are the controls studio engineers use most). But just as a studio LA-2A can dramatically recast a sound with these simple interactions, the Mary Cries has the capacity to completely alter the feel and force of an instrument—beyond adding sustain and mitigating the effects of nasty peaks.
Even modest compression settings on the Mary Cries also have the effect of thickening and tightening low- and low-mid frequencies, giving the perception of extra mass and resonance without overpowering the top end. Mary Cries also colors trebles with bell-like sustain that tends to decay in almost perfect balance with the fatter low end. Players often use comps to achieve balance between frequency band extremes, but the Mary Cries’ cohesiveness, if you’ll permit a food analogy, has the feel of a sauce where every ingredient shines brilliantly.
This ability to gather and highlight fundamentals and overtones in a balanced whole does wonders for simple and extended chords. And these tone composites can purr and growl gorgeously depending on where you situate your output gain. Incidentally, Mary Cries is a magnificent clean boost when you kick up the output gain and reduce the compression to a minimum.
The Verdict
Mary Cries does a superb job of sounding and feeling transformative with very little fuss. It’s beautifully built, which manifests itself in the unit’s exceptionally quiet performance. At 219 bucks, it may seem expensive to players accustomed to other superficially simple comps. But I suspect even a cursory side-by-side play with many of these units would reveal much about Mary Cries’ nuance, elegance, and value.
Wind Through the Trees Dual Analog Flanger
Compared to its relatively streamlined siblings the Mary Cries and the Horsemeat, the analog, LFO-driven Wind Through the Trees flanger looks like a handful to manage. But for all the knobs that populate the Wind’s enclosure, it’s surprisingly intuitive.
Many contemporary, digitally attuned players will insist that a pedal this full of possibilities should come with presets. But the Wind Through the Trees’ analog interface is fluid and clear enough that you can move between varied settings with relative ease. That makes exploring the pedal’s myriad textures a flat-out joy—particularly because you can home in on very specific modulation profiles to suit a musical moment.
“One of the Wind Through the Trees greatest strengths is its ability to generate very mellow and hauntingly subliminal modulations.”
Flange is not an effect players typically associate with subtlety. But one of the Wind Through the Trees’ greatest strengths is its ability to generate very mellow and hauntingly subliminal modulations. These subtleties are made possible by the Wind Through the Trees very interactive, sensitive, and rangy controls. And, in my experience at least, the LFO mix, wet/dry output, and the very clearly labeled “added highs” controls are key to these textures.
Using these controls, you can, for instance, fashion a very understated modulation on LFO 1, blend in just a touch of twitchy, deep, high-rate modulation from LFO 2, add a touch of haze or brightness to taste with the added highs control, and then mix the sum into your signal with the very sensitive dry/wet knob. These are obviously not revolutionary means of control, but the way they work on the Wind Through the Trees feels surgical and gives you a real sense of command where some flangers feel monochromatic or purely chaotic.
But if chaos—or at least the surreal—is what you crave, the Wind Through the trees can deliver. For instance, very effective, weird-but-musical textures can be crafted by dialing closely adjacent but just offset rate and depth settings in the two LFOs, then setting their respective manual (or waveform delay) controls in opposition and cranking the regen to extra whooshy levels. Using the same scheme but mixing slow and fast rate settings in the two LFOs yields even stranger and more complex variations that combine hints of rotary speaker and ring modulation. And backgrounding these wild combinations by subtracting high end and using a dryer mix adds mysterious animation to chords and melody lines.
The Verdict
At about 350 bucks, the Wind Through the Trees is the most expensive of the new PRS pedals. And it’s understandable that some might perceive that price as high for an effect that’s, ostensibly, specialized. But the Wind Through the Trees proves how expansive a flanger can be when done right. There are lovely chorus-like sounds, plenty of intense vintage phase tones, and the deep but elegant and intuitive control set makes crafting complex modulations feel effortlessly creative.
Players accustomed to presets on a pedal with such broad capabilities may be bummed by their absence. And it’s true that moving between vastly different flange settings in the midst of a performance won’t always be a piece of cake. But in the context of song creation and in the studio, where you have the luxury of hunting for the perfect modulation color, Wind Through The Trees can be a potent musical companion.
- First Look: PRS SE Silver Sky John Mayer - Premier Guitar ›
- Factory Tour: PRS Guitars - Premier Guitar ›
- When Exactly Did "Boutique Pedals" Become a Thing? - Premier ... ›
- Messiah Guitars Introduces Dandelion Fuzz & Quiggly Octofuzz - Premier Guitar ›
- Paul Reed Smith Ends the Tonewood Debate - Premier Guitar ›
- PG Explained: Guitar Pedals/Effects - Premier Guitar ›
Vox’s Valvenergy Tone Sculptor
Two new pedals from the Valvenergy series use a Nutube valve to generate unique dynamics and tone ranges that can be used to radical ends.
When tracking in a studio or DAW, you’re likely to use compression and EQ on most things. Many enduringly amazing and powerful records were made using little else. And though many musicians regard both effects as a bit unglamorous and utilitarian, EQs and comps are as capable of radical sounds as more overtly “weird” effects—particularly when they are used in tandem.
I spent a day workshopping ideas in my studio using just the Vox Valvenergy Smooth Impact compressor and Tone Sculptor EQ, and a dash of amp tremolo and reverb to taste. In the process, I produced more arresting sounds than I had heard from my guitars in many days. There were radical direct-to-desk-style Jimmy Page/Beatles distortion tones, sun-sized, cosmic electric 12-string, Bakersfield twang that could burn through crude, and many other sweet and nasty colors. Most decent EQ and compressor combinations can achieve variations on all those themes. But the Smooth Impact and Tone Sculptor also reveal interesting personalities in unexpected places.
The individuality and energy in the Vox Valvenergy pedals is attributable, in part, to the Nutube vacuum tube used in the circuit. Though it looks little like a vacuum tube as most guitarists know them, the thin, wafer-like Nutube is, in fact, a real vacuum tube like those used in fluorescent displays. Fluorescent display tubes have limitations. A maximum operating voltage of around 40 volts means they aren’t useful for bigger power tube applications like a 6L6, which has an operating voltage of about 400 volts. But it can work quite well as a preamp tube in concert with an op amp power section, which is how the Nutube is used in the new Valvenergy pedals, as well as older Vox products like the Vox MV50 and Superbeetle amps.
Valvenergy Tone Sculptor
When you think about “cinematic” effects, you likely imagine big reverb or modulation sounds that create a vivid picture and feeling of space or motion. But narrow, hyper-focused EQ profiles can evoke very different and equally powerful images. Radical EQ settings can add aggression, claustrophobic intimacy, and stark, explosive dark-and-light contrasts more evocative of Hitchcock’s Psycho than Ridley Scott’s Blade Runner.
Any of these moods can be summoned from the Valvenergy Tone Sculptor. Six sliders cut or boost 10 dB frequency bands spanning 100 Hz to 5.6 kHz. A seventh slider cuts or boosts the master output by 12 dB. This platter of options might not sound like much. But you can use these seven controls together to very specific ends.
“Radical EQ settings can add aggression, near-claustrophobic intimacy, and stark, explosive dark-and-light contrasts.”
For example, bumping the high-midrange and the master output produces narrow cocked-wah-like filter sounds with enough push to produce extra amp overdrive—effectively turning the Tone Sculptor into a buzzy, almost fuzz-like filter effect. But unlike a wah, you can carefully scoop high end or add a spoonful of bass to blunt harsh frequencies or give the tone a bit more weight. You can also broaden the palette of an amp/guitar pairing. I matched a particularly trebly Jazzmaster bridge pickup with a very hot and toppy Vox AC15-flavored amp for this test—a recipe that can be spiky on the best days. But with the Tone Sculptor in the line, I could utilize the same sharp, fuzzy, and filtered Mick Ronson wah tones while shaving some of the most piercing frequencies.
EQ pedals exist on many points along the cost spectrum. And at $219, the Tone Sculptor lives on the high side of the affordable range. Does it offer something less expensive models can’t deliver? Well, for one thing, I found it relatively quiet, which is nice whether you’re shaping toppy high-contrast effects or performing more surgical adjustments. And the sliders feel nuanced and nicely tapered rather than like a dull axe with a few basic frequency notches. But in many situations I also liked the color imparted by the circuit—generated, presumably, by the Nutube. “Color,” in audio terms, is a broad and subjective thing, and one should not necessarily expect the warm, tube-y glow of a vintage tube Pultec. Still, the Tone Sculptor has many forgiving, flattering qualities—typical of studio EQs—that enable fine tuning and experimentation with more radical and creative applications of the effect.
Valvenergy Smooth Impact
As with the Tone Sculptor, the Smooth Impact’s use of Nutube engenders certain expectations. It’s easy to surmise that because Smooth Impact has a vacuum tube in the circuit that it will behave like a little Teletronix LA-2A leveling amplifier. That’s a big ask for a $219 stompbox. On the other hand, the Smooth Impact exhibits some appealing characteristics of studio tube compression. At lower compression levels, it works well as a thickening agent—adding mass without much additional noise. And at higher compression levels it can sound snappy, crisp, and tight without feeling like you’ve bled every trace of overtone from your signal.
The Smooth Impact’s controls aren’t totally atypical. But because it lacks some familiar features like variable attack and release, yet is more complicated than a 1-knob DynaComp, you have to trust your ear to navigate interactions among the controls. The most unfamiliar of these is the 3-way vintage/natural/sag toggle. The first two are defined by preset attack and release settings: Vintage is slow attack and long release, and natural is the opposite. The sag mode’s compression is more like what you get from tube saturation, and it’s useful for adding thickness and complexity to a thin amp tone at modest compression levels.
Though the vintage and natural modes certainly have a different feel, they don’t always sound worlds apart. And like the sag mode, the thing they have in common is the way they enrich lifeless amp output at low to medium compression, with a bit of grind from the tube gain and a little extra makeup gain from the output. At the most aggressive settings, the tube gain can get a little crispy. And really crushing the compression can flatline your tone without adding much in the way of extra sustain. These are limitations common to many compressors with similar features. But unless I was chasing very ultra-snappy Prince and Nile Rodgers fast-funk caricatures, I enjoyed the Smooth Impact most in its in-between ranges, where mass, mild, harmonious drive, and low noise showcase the pedal’s sometimes studio-like personality.
Significantly smaller and lighter than original TAE. Easy to configure and operate. Great value. Streamlined control set.
Air Feel Level control takes the place of more surgical and realistic resonance controls. Seventy watts less power in onboard power amp. No Bluetooth connectivity with desktop app.
$699
Boss Waza Tube Amp Expander Core
Boss streamlines the size, features, and price of the already excellent Waza Tube Expander with little sacrifice in functionality.
Many of our younger selves would struggle to understand the urge—indeed, the need—to play quieter. My first real confrontation with this ever-more-present reality arrived when Covid came to town. For many months, I could only sneak into my studio space late at night to jam or review anything loud. Ultimately, the thing that made it possible to create and do my job in my little apartment was a reactive load box (in this case, a Universal Audio OX). I set up a Bassman head next to my desk and, with the help of the OX, did the work of a gear editor as well as recorded several very cathartic heavy jams, with the Bassman up to 10, that left my neighbors none the wiser.
Boss’ firstWaza Tube Amp Expander, built with an integrated power amp that enables boosted signal as well as attenuated sounds, was and remains the OX’s main competition. Both products have copious merits but, at $1,299 (Boss) and $1,499 (Universal Audio), each is expensive. And while both units are relatively compact, they aren’t gear most folks casually toss in a backpack on the way out the door. The new Waza Tube Expander Core, however, just might be. And though it sacrifices some refinements for smaller size, its much-more accessible price and strong, streamlined fundamental capabilities make it a load-box alternative that could sway skeptics.
Micro Manager
The TAE Core is around 7 1/2" wide, just over 7 " long, and fewer than 4 " tall, including the rubber feet. That’s about half the width of an original TAE or OX. The practical upside of this size reduction is obvious and will probably compel a lot of players to use the unit in situations in which they’d leave a full-size TAE at home. The streamlined design is another source of comfort. With just five knobs on its face, the TAE Core has fewer controls and is easier to use than many stompboxes. In fact, the most complicated part of integrating the TAE Core to your rig might be downloading the necessary drivers and related apps.
Connectivity is straightforward, though there are some limitations. You can use TAE Core wirelessly with an iOS or Windows tablet or smartphone, as long as you have the BT-DUAL adaptor (which is not included and sets you back around 40 bucks). However, while desktop computers recognize the TAE Core as a Bluetooth-enabled device, you cannot use the unit wirelessly with those machines. Instead, you have to connect the TAE Core via USB. In a perfectly ordered world, that’s not a big problem. But if you use the TAE Core in a small studio—where one less cable is one less headache—or you prefer to interface with the TAE Core app on a desktop where you can toggle fast and easily between large, multi-track sessions and the app, the inability to work wirelessly on a desktop can be a distraction. The upside is that the TAE Core app itself is, functionally and visually, almost identical in mobile and desktop versions, enabling you to select and drag and drop virtual microphones into position, add delay, reverb, compression, and EQ effects, choose various cabinets with different speaker configurations and sizes, and introduce new rigs and impulse responses to a tone recipe in a flash. And though the TAE Core app lacks some of the photorealistic panache and configuration options in the OX app, the TAE Core’s app is just as intuitive.Less Is More
One nice thing about the TAE Core’s more approachable $699 price is that you don’t have to feel too bad on nights that you “underutilize” the unit and employ it as an attenuator alone. In this role, the TAE Core excels. Even significantly attenuated sounds retain the color and essence of the source tone. Like any attenuator-type device, you will sacrifice touch sensitivity and dynamics at a certain volume level, yielding a sense of disconnection between fingers, gut, guitar, and amp. But if you’re tracking “big” sounds in a small space, you can generate massive-sounding ones without interfacing with an amp modeler and flat-response monitors, which is a joy in my book. And again, there’s the TAE Core’s ability to “expand” as well as attenuate, which means you can use the TAE Core’s 30-watt onboard power amp to amplify the signal from, say, a 5-watt Fender Champion 600 with a 6" speaker, route it to a 2x12, 4x12, or virtual equivalent in the app, and leave your bandmate with the Twin Reverb and bad attitude utterly perplexed.
The Verdict
Opting for the simpler, thriftier TAE Core requires a few sacrifices. Power users that grew accustomed to the original TAE’s super-tunable “resonance-Z” and “presence-Z” controls, which aped signal-chain impedance relationships with sharp precision, will have to make do with the simpler but still very effective stack and combo options and the “air feel level” spatial ambience control.The DC power jack is less robust. It features only MIDI-in rather than MIDI-in/-through/-out jacks, and, significantly, 70 watts less power in the onboard power amp. But from my perspective, the Core is no less “professional” in terms of what it can achieve on a stage or in a studio of any size. Its more modest feature set and dimensions are, in my estimation, utility enhancements as much as limitations. If greater power and MIDI connectivity are essentials, then the extra 600 bones for the original TAE will be worth the price. For many of us, though, the mix of value, operational efficiencies, and the less-encumbered path to sound creation built into the TAE Core will represent a welcome sweet spot that makes dabbling in this very useful technology an appealing, practical proposition.
Darkglass Electronics unveils ANAGRAM, a flagship bass platform designed to redefine tone, flexibility, and performance. The pedal’s extraordinarily deep feature set includes multiple effects and modeling, an on-board looper and tuner.
Best of all, ANAGRAM brings together these creative tools in a streamlined, rugged format that’s designed for ease of use. Onstage and in the studio, bassists can quickly access and fine-tune their sound via the ANAGRAM interface:
- 7-inch high-brightness touchscreen for clear and intuitive control.
- Three footswitches for live performance control.
- Six high-resolution endless rotary knobs for precise parameter adjustments.
- Flexible input and output configuration.
With ultra-low latency, extensive customization, and seamless integration into the Darkglass ecosystem, it supports both studio precision and stage performance. Combining 15 years of innovation with cutting-edge processing power, ANAGRAM offers a purpose-built solution for bassists seeking unparalleled sound-shaping capabilities.
Anagram
Powered by a state-of-the-art hexacore processor and 32-bit/48kHz audio processing,ANAGRAM delivers ultra-low latency, pristine clarity, and studio-grade sound. Its intuitive blocks-based architecture lets players create signal chains in series (12 blocks) or parallel (24blocks) using a high-resolution touch display. ANAGRAM features three control modes—Preset,Scene, and Stomp—for instant switching, parameter adjustments, and traditional pedalboard-style operation. With a curated collection of distinct preamps, 50+ customizable effects, a looper, tuner, and user-generated IR support, ANAGRAM delivers unmatched creative flexibility.Seamless integration with the Darkglass Suite allows for expanded control and functionality. Additionally, Neural Amp Modeler (NAM) integration provides access to thousands
of high-quality amp and effect models, expanding tonal possibilities from analog warmth to futuristic textures.
"Anagram represents the culmination of years of research and development," says Marcos Barilatti, Managing Director of Darkglass Electronics. "We set out to create a product that not only pushes the boundaries of bass tone but also inspires musicians to explore new sonic territories."
Housed in a rugged anodized aluminum chassis, ANAGRAM is road-ready, compact, and powered via 9V or USB-C (PD). With flagship features at a compelling price, ANAGRAM represents the new standard for bassists seeking a modern platform for their performance.
Street $1199.99 USD
Alongside Nicolas Jaar’s electronics, Harrington creates epic sagas of sound with a team of fine-tuned pedalboards.
Guitarist Dave Harrington concedes that while there are a few mile markers in the music that he and musician Nicolas Jaar create as Darkside, improvisation has been the rule from day one. The experimental electronic trio’s latest record, Nothing, which released in February on Matador, was the first to feature new percussionist Tlacael Esparza.
Taking the record on tour this year, Darkside stopped in at Nashville’s Brooklyn Bowl, where Harrington broke down his complex signal chains for PG’s Chris Kies.
Brought to you by D’Addario.
Express Yourself
Harrington bought this mid-2000s Gibson SG at 30th Street Guitars in New York, a shop he used to visit as a kid. The headstock had already been broken and repaired, and Harrington switched the neck pickup to a Seymour Duncan model used by Derek Trucks. Harrington runs it with D’Addario NYXL .010s, which he prefers for their stretch and stability.
The standout feature is a round knob installed by his tech behind the bridge, which operates like an expression pedal for the Line 6 DL4. Harrington has extras on hand in case one breaks.
Triple Threat
Harrington’s backline setup in Nashville included two Fender Twin Reverbs and one Fender Hot Rod DeVille. He likes the reissue Fender amps for their reliability and clean headroom. Each amp handles an individual signal, including loops that Harrington creates and plays over; with each amp handling just one signal rather than one handling all loops and live playing, there’s less loss of definition and competition for frequency space.
Dave Harrington’s Pedalboards
Harrington says he never gives up on a pedal, which could explain why he’s got so many. You’re going to have to tune in to the full Rundown to get the proper scoop on how Harrington conducts his three-section orchestra of stomps, but at his feet, he runs a board with a Chase Bliss Habit, Mu-Tron Micro-Tron IV, Eventide PitchFactor, Eventide H90, Hologram Microcosm, Hologram Chroma Console, Walrus Monument, Chase Bliss Thermae, Chase Bliss Brothers AM, JHS NOTAKLÖN, two HexeFX reVOLVERs, and an Amped Innovations JJJ Special Harmonics Extender. A Strymon Ojai provides power.
At hip-level sits a board with a ZVEX Mastotron, Electro-Harmonix Cathedral, EHX Pitch Fork, Xotic EP Booster, two EHX 45000 multi-track looping recorders, Walrus Slöer, Expedition Electronics 60 Second Deluxe, and another Hologram Microcosm. A Live Wire Solutions ABY Box and MXR DC Brick are among the utility tools on deck.
Under that board rest Harrington’s beloved Line 6 DL4—his desert-island, must-have pedal—along with a controller for the EHX 45000, Boss FV-50H volume pedal, Dunlop expression pedal, Boss RT-20, a Radial ProD2, and another MXR DC Brick.