Name: Steve Kellett
Hometown: Petaling Jaya, Malaysia
Guitar: Made-in-Japsn Japan Telecaster
Here’s the tale of my Fender Made-in-Japan Telecaster: I bought this guitar in 1996 in Hong Kong from the Tom Lee Music Annual Warehouse Clearance Sale. I didn’t hear about the sale until the last day, so by the time I rocked up to the rented factory unit in the depths of Mong Kok, where they were holding the sale, there were only two guitars left: a wrecked, cheap acoustic and a made-in-Japan export model foto flame ’50s Telecaster.
As you can see from Photo 2, the guitar originally had a cherry sunburst finish on the body, but as it dated from ’94 and was one of the first-run foto flames, it had a plain maple V-shaped neck and maple fretboard with vintage-sized frets.
Originally, it had the low-end export electronics: bar-magnet pickups and dime-sized pots. I played it like this for two or three years, and then I got the itch to upgrade the pickups. So, I found a Seymour Duncan Jerry Donahue bridge pickup and a ’52 Fender reissue neck pickup, which I fitted.
Shortly after that, the tone pot disintegrated, so I bought a set of U.S. CTS pots and fitted those. This involved reaming out the holes in the control plate to accommodate the slightly larger pot shafts. To do this, I used a round file and elbow grease. About this time, I also acquired a set of brass bridge saddles to replace the original steel ones. The Telecaster Discussion Page Reissue online guitar forum has a lot to answer for.
Fast forward to about 2010, and the foto flame did what foto flame does: it started to crack. As you can see in Photo 2, it got pretty bad. I tried to address it using superglue, but that just made matters worse.
Photo 2
A couple of months ago, I had just had a local luthier do some repair work on a late ’60s Antoria Soundmaster. When he’d completed that, I asked if he could take the Tele and use veneer to properly achieve the effect that the foto flame had originally achieved. Well, he couldn’t find any decent figured maple veneer locally, but instead we selected some figured movingui and a tobacco sunburst finish base. Photo 1 shows the final result.
While he was at it, he also replaced the neck pickup cover with an open-topped cover exposing the polepieces, and a 4-way switch, giving series and parallel options for the pickup combination. We figured that the original white pickguard wouldn’t look that great with the new finish, so I picked up both black and faux tortoise-shell guards from Musiclily, and after the refinish, we figured that the black guard looked the best. The finished guitar can be seen in Photo 1. What can I say? It is like having a new guitar.
Send your guitar story to submissions@premierguitar.com.
- Reader Guitar of the Month: The Wolf ›
- Reader Guitar of the Month: A National Treasure ›
- Reader Guitar of the Month: Bertha ›
- Reader Guitar of the Month: A Doubleneck Bass and Guitar - Premier Guitar ›
- In Flames Rig: Björn Gelotte, Chris Broderick & Liam Wilson - Premier Guitar ›
Over the decades with Hüsker Dü, Sugar, and solo, Bob Mould has earned a reputation for visceral performances.
Mould’s album landed in a world of cloistered listeners, so he never knew how it impacted people. For a musician from punk and hardcore scenes, it was a disquieting experience. So when he got back out on the road in 2023 and 2024, playing solo electric sets, the former Hüsker Dü and Sugar frontman was determined to reconnect with his listeners. After each show, he’d hang out at the merch table and talk. Some people wanted their records or shirts signed, some wanted a picture. Others shared dark stories and secret experiences connected to Mould’s work. It humbled and moved him. “I’m grateful for all of it,” he says.
These are the in-person viscera of a group of people connecting on shared interests, versus, says Mould, “‘I gotta clean the house today, so I’m going to put on my clean the house playlist that a computer designed for me.” “Everything has become so digitized,” he laments. “I grew up where music was religion, it was life, it was essential. When people come to shows, and there’s an atmosphere, there’s volume, there’s spilled drinks and sweat–that’s what music ritual is supposed to be.”
His experiences on tour after the pandemic heartened Mould, but they also gave him traction on new ideas and direction for a new record. He returned to the simple, dirty guitar-pop music that spiked his heart rate when he was young: the Ramones’ stupid-simple pop-punk ecstasy, New York Dolls’ sharp-edged playfulness, Pete Townshend’s epic, chest-rattling guitar theatrics. In other words, the sort of snotty, poppy, wide-open rock we heard and loved on Hüsker Dü’s Flip Your Wig and Candy Apple Grey.
Mould’s time on the road playing solo in 2023 sparked the idea for Here We Go Crazy.
Photo by Ryan Bakerink
Mould started writing new songs in the vein of his original childhood heroes, working them into those electric solo sets in 2023 and 2024. Working with those restraints—guitar chords and vocal melodies—put Mould on track to make Here We Go Crazy, his new, 15th solo record.
Lead single and opener “Here We Go Crazy” is a scene-setting piece of fuzzy ’90s alt-rock, bookended by the fierce pounding of “Neanderthal.” “When Your Heart is Broken” is a standout, with its bubblegum chorus melody and rumbling, tense, Who-style holding pattern before one of the album’s only solos. Ditto “Sharp Little Pieces,” with perhaps the record’s chewiest, darkest guitar sounds.
“It’s a very familiar-sounding record,” he continues. “I think when people hear it, they will go, ‘Oh my god, this is so Bob Mould,’ and a lot of that was [influenced by] spending time with the audience again, putting new stuff into the set alongside the songbook material, going out to the table after the show and getting reactions from people. That sort of steered me towards a very simple, energetic, guitar-driven pop record.”
Of his new album, Mould says, “I think when people hear it, they will go, ‘Oh my god, this is so Bob Mould.’”
Mould recorded the LP in Chicago with longtime bandmates Jason Narducy and Jon Wurster at the late, great Steve Albini’s Electrical Audio. Then Mould retreated to San Francisco to finish the record, chipping away at vocals and extra guitar pieces. He mostly resisted the pull of “non-guitar ornamentation”: “It’s a rhythm guitar record with a couple leads and a Minimoog,” he says. “It’s sort of cool to not have a 64-crayon set every time.”
Mould relied on his favorite, now-signature late-’80s Fender Strat Plus, which sat out on a runway at O’Hare in 20-below cold for three hours and needed a few days to get back in fighting shape. In the studio, he ran the Strat into his signature Tym Guitars Sky Patch, a take on the MXR Distortion+, then onto a Radial JD7. The Radial split his signal and sent it to three combo amps: a Fender Hot Rod DeVille, a Fender ’68 Custom Deluxe Reverb reissue, and a Blackstar Artisan 30, each with a mic on it. The result is a brighter record that Mould says leaves more room for the bass and kick drum. “If you listen to this record against Patch the Sky, for instance, it’s night and day,” he says. “It’s snug.”
Mould explains that the record unfolds over three acts. Tracks one through five comprise the first episode, crackling with uncertainty and conflict. The second, spread over songs six to eight, contrasts feelings of openness with tight, claustrophobic tension. Here, there are dead ends, addictions, and frigid realities. But after “Sharp Little Pieces,” the album turns its corner, barreling toward the home stretch in a fury of optimism and determination. “These last three [songs] should give us more hope,” says Mould. “They should talk about unconditional love.”
The record closes on the ballad “Your Side,” which starts gentle and ends in a rush of smashed chords and cymbals, undoubtedly one of the most invigorating segments. “The world is going down in flames, I wanna be by your side/We can find a quiet place, it doesn’t need to be the Albert Hall,” Mould starts. It’s a beautiful portrait of love, aging, and the passage of time.
Bob Mould's Gear
Mould paired his trusty Fender Strat Plus with a trio of smaller combo amps to carve out a more mid-focused rhythm-guitar sound in the studio.
Photo by Mike White
Guitars
- Late 1980s Fender American Standard Strat Plus (multiple)
Amps
- Fender Hot Rod DeVille
- Blackstar Artisan Series amps
- Fender '68 Custom Deluxe Reverb
Effects
- Tym Guitars Sky Patch
- TC Electronic Flashback
- Electro-Harmonix Freeze
- Wampler Ego
- Universal Audio 1176
- Radial JD7
Strings, Picks, & Power Supply
- D'Addario NYXLs (.011-.046)
- Dunlop .46 mm and .60 mm picks
- Voodoo Labs power supply
And though the record ends on this palette of tenderness and connection, the cycle is likely to start all over again. Mould understands this; even though he knows he’s basking in act three at the moment, acts one and two will come along again, and again. Thankfully, he’s figured out how to weather the changes.
“When things are good, enjoy them,” he says. “When things are tough, do the work and get out of it, somehow.”
- YouTube
Many of the tracks on Here We Go Crazy were road-tested by Mould during solo sets. Here, accompanied only by his trusty Fender Strat, he belts “Breathing Room.”
Reader: Federico Novelli
Hometown: Genoa, Italy
Guitar: The Italian Hybrid
Reader Federico Novelli constructed this hybrid guitar from three layers of pine, courtesy of some old shelves he had laying around.
A few years ago, at the beginning of Covid, an idea for a new guitar flashed through my mind. It was a semi-acoustic model with both magnetic and piezo pickups that were mounted on a soundboard that could resonate. It was a nice idea, but I also had to think about how to make it in my tiny cellar without many power tools and using old solid-wood shelves I had available.
I have been playing guitar for 50 years, and I also dabble in luthiery for fun. I have owned a classical guitar, an acoustic guitar, and a Stratocaster, but a jazz guitar was missing from the list. I wanted something that would have more versatility, so the idea of a hybrid semi-acoustic guitar was born.
I started to sketch something on computer-aided design (CAD) software, thinking of a hollowbody design without a center block or sides that needed to be hot-worked with a bending machine. I thought of a construction made of three layers of solid pine wood, individually worked and then glued together in layers, with a single-cutaway body and a glued-in neck.
For the soundboard and back, I used a piece of ash and hand-cut it with a Japanese saw to the proper thickness, so I had two sheets to fit together. Next, I sanded the soundboard and bottom using two striker profiles as sleds and an aluminum box covered in sandpaper to achieve a uniform 3 mm thickness. A huge amount of work, but it didn't cost anything.
“It was a nice idea, but I also had to think about how to make it in my tiny cellar without many electric tools and out of old solid-wood shelves I had available.”
The soundboard has simplified X-bracing, a soundhole with a rosewood edge profile, and an acoustic-style rosewood bridge. For the neck, I used a piece of old furniture with straight grain, shaped it to a Les Paul profile, and added a single-action truss rod. The only new purchase: a cheap Chinese rosewood fretboard.
Then, there was lots of sanding. I worked up to 400-grit, added filler, primer, and transparent nitro varnish, worked the sandpaper up to 1,500-grit, and finally polished.
Our reader and his “Italian job.”
For electronics, I used a Tonerider alnico 2 humbucker pickup and a piezo undersaddle pickup, combined with a modified Shadow preamp that also includes a magnetic pickup input, so you can mix the two sources on a single output. I also installed a bypass switch for power on/off and a direct passive output.
I have to say that I am proud and moderately satisfied both aesthetically and with the sounds it produces, which range from jazz to acoustic and even gypsy jazz. However, I think I will replace the electronics and piezo with Fishman hardware in the future.
