
For part two of our crash course in harmony for bassists, we’re talkin’ triads.
As bass players, our job is often to indicate and support what is happening rhythmically and harmonically in the music we’re playing. And to do that, it’s important for us to understand the basics of tonality and how it works. In fact, every bass player must have a strong knowledge of harmony to do their job correctly. This month, we’ll continue last month’s harmony crash course with some more ways to brush up on your ear skills, in italics below, so you can do your low-end job effectively.
The basic building block of harmony is the dyad, which gives us our basic intervals. But the basic building block of tonality is the triad, a grouping of three or more tones (root, 3rd, and 5th) that give us the four chord qualities—major, minor, diminished, and augmented—which you’re probably already familiar with.
Just as with intervals, we should train our ears to recognize chord qualities instantly. Start with two qualities (major and minor). Once you can identify those two correctly about 95 percent of the time, add another. Keep going until you can identify all four qualities consistently.
Another great exercise is to take a melody (either major or minor) and convert it to the opposite quality. Start out with something you know well, like “Twinkle, Twinkle, Little Star.” This may take a while at first, but the goal is to keep on doing these until you can convert most stuff on the fly instantly.
“This feeling of resolution, in some ways, is the whole point.”
Each chord quality has its own distinct sound, but major and minor are related, and both feel very grounded. Because of the 5th in each, our ears can easily hear which note in the chord is strongest (the root), which gives major and minor a sense of gravity. This feeling persists even if we change the order of the notes (invert the chord).
Have a friend or an app play inversions of major or minor triads. Find the root of each chord by singing it. Work towards being able to identify these triads in root position (root in the bass), first inversion (3rd in the bass), or second inversion (5th in the bass).
Pay attention to bass lines that land on a root, 3rd, or 5th on the first beat of the bar and then practice coming up with your own examples.
Diminished and augmented triads are much more ambiguous. Without a perfect fifth (diminished has a b5 and augmented has a #5), no tone in particular sounds strongest. Thus, both chords lack gravity. In fact, to most of us, every tone sounds equal, like being lost in the woods where every direction appears the same. Both seem to want to move towards something else more stable. When this occurs, it gives a sense of release, or resolution. This feeling of resolution, in some ways, is the whole point.
The top part of a dominant seventh or V7 chord is a diminished triad. For example, a C7 consists of the notes C–E–G–Bb. If you remove the C, we’re left with an E diminished triad. This is where the moving sound, or the desire to resolve, comes from. The important takeaway is that we’re making something very stable—a major chord—and making it less stable when we add the b7, because of the diminished sound, which in turn sets up the need to resolve.
Listening for V–I: On a guitar or keyboard play any major chord, then add a b7 (transforming I to V7) and try to hear where the progression “wants” to go next. Move to the new key (a fifth down) and repeat. After twelve V–I progressions you’ll arrive back at the original key.
The Dominant Gateway: On bass, try playing a walking bass pattern over the cycle of fifths, strategically using a b7 to move to the next key. This foreshadowing is a great voice-leading skill.
That's all for our crash course in harmony. If you take your time with these exercises, you should notice not only your ears improving, but your bass playing too!
- Top 5 Bass Rig Rundowns ›
- Flashy Is Fun, But the Bass Has a Deeper Function - Premier Guitar ›
- How NOT to Play Bass like a Guitar Player Playing Bass - Premier ... ›
The Mick Ronson Cry Baby Wah, meticulously recreated from his own pedal, offers fixed-wah tones with a custom inductor for a unique sound.
The Mick Ronson Cry Baby Wah taps into the vibrant, melodic character of one of rock ’n’ roll’s most gifted songwriters. Few guitar players have been able to combine a keen musical instinct with a profound grasp of how to bring a composition together like Mick Ronson. Laden with expressive resonance, his arrangements layered deliberately chosen tones and textures to build exquisite melodies and powerful riffs. The Cry Baby Wah, set in a fixed position to serve as a filter, was key to the tone-shaping vision that Ronson used to transform the face of popular music through his work with David Bowie and many others as both an artist and a producer.
We wanted to make that incredible Cry Baby Wah sound available to all players, and legendary producer Bob Rock—a friend and collaborator of Ronson’s—was there to help. He generously loaned us Ronson’s own Cry Baby Wah pedal, an early Italian-made model whose vintage components imbue it with a truly singular sound. Ronson recorded many tracks with this pedal, and Rock would go on to use it when recording numerous other artists. With matched specs, tightened tolerances, and a custom inductor, our engineers have recreated this truly special sound.
“You place the wah, and leave it there, and that's the tone,” Rock says. “It's all over every record he ever made, and I’ve used it on every record since I got it. Dunlop’s engineers spent the time and sent me the prototypes, and we nailed that sound.”
Mick Ronson Cry Baby Wah highlights:
- Tailor-made for Ronson’s signature fixed-wah tones• Carefully spec’d from his own wah pedal
- Custom inductor replicates higher frequency response and subtler peak
- Fast initial sweep with Instant reactivity
- Distinctive EQ curve from period-accurate components
- Special finish inspired by Ronson’s monumental work
The Mick Ronson Cry Baby Wah is available now at $249.99 street from your favorite retailer.
For more information, please visit jimdunlop.com.
What if you could have the best of both—or multiple—worlds? Our columnist investigates.
This column is a fun and educational thought experiment: What if I took inspiration from the well-known Fender amps out there, combined the best from them, and applied a few of my own twists? After all, this is how amps developed. I read somewhere that “Fender made the first Marshall, and Marshall made the first reissue Fender.” It's funny, because it's true: The Marshall JTM45 was based on the narrow-panel tweed Fender Bassman 5F6-A.
Before we start, I’d like to share my respect for the real entrepreneurs who get into the gear industry. The financial and commercial challenges are of existential magnitude, and I can only imagine the complexity of scaling up production lines. For now, let’s start with the easy part: designing the amps of our dreams.
The Smarter Deluxe Reverb
The idea behind this amp is to enhance the black-panel Deluxe Reverb by making it simpler, yet more versatile. First, we’d need an extra 2 cm of cabinet height for better clearance between the output transformer and the magnet of a heavy-duty 12" speaker. The extra ambience and fullness from the slightly larger cabinet would be appreciated by many who find the Deluxe too small on larger stages. I’d offer both 2x10 and 1x12 speaker baffles of birch plywood that are more durable than MDF particle boards.
For the 2x10 version, there would be simple on/off switches on the lower back plate to disconnect the speaker wires. That way, players could disable one speaker to easily reduce volume and headroom, or select between two different sounding speakers. Also, these switches will enable super-easy speaker comparisons at home. There would be a 4- and 8-ohm impedance selector based on a multi-tap output transformer that is the size of a Vibrolux Reverb 125A6A transformer—one size bigger than the Deluxe´s 125A1A. This would tighten up the low-end response to accommodate the bigger cabinet.
Like the Princeton Reverb, the amp would be single-channel with reverb and tremolo, but with only one input jack. I would keep the Deluxe’s tone stack, and add a bright switch and a mid-control with a larger 20-25K mid-pot value instead of the Fender-default 10K. This would enable players to dial in many more tones between a scooped American sound and a British growl. The power amp section is 100 percent Deluxe Reverb, which would allow 6L6 tube swaps without the need to change anything else. The full power of the 6L6 will not be utilized due to the lower 6V6 plate voltages, but it gives you some extra headroom. To reduce costs and complexity, I would use a diode rectifier and transistors in the reverb circuitry, like the modern Blues Junior. This saves two tubes and creates less trouble down the road. The tremolo would be based on the Princeton Reverb’s bias-based tremolo circuit, since it sweeps deeper than the Deluxe Reverb’s optoisolator tremolo.
The Bassman Pro Reverb
My second amp would be a large, warm-sounding amp with preamp distortion abilities. I really like the Vibro-King and tweed Bassman 5F6-A circuit designs, where the volume control is placed alone before a 12AX7 preamp tube stage and then followed by the EQ section. This means that a high volume-knob setting allows a strong signal to enter the 12AX7, creating a distorted signal at the tube’s output. This distorted signal then enters the bass, mid, and treble pots afterward, which can lower the still-distorted signal amplitude before the phase inverter and power amp section. With this preamp design, you can achieve a heavily cranked tone at low volumes based on preamp distortion and clean power amp operation. This trick is not possible with the typical AB763 amps, where the volume and EQ work together at the same stage. If you set the volume high and the bass, mids, and treble low, they cancel each other before hitting the next tube stage.
“This amp could do it all: pleasant cleans and distortion at both moderate and loud levels.”
I would use a Pro Reverb-sized 2x12 cabinet for this amp, with the output impedance selector and speaker switches I mentioned earlier. The amp would have dual 6L6s in push/pull, and a Super Reverb-sized 125A9A output transformer for a firm low end at 40-watt power output. I would go for cathode bias in this amp, for a compressed, low-wattage, tweed-style response, to add even more dirt next after the hot preamp section. There is only one jack input into the single channel, with reverb, tremolo, and full EQ controls (bright switch, bass, mid, and treble). Since this would be a more costly amp, I’d use a tube rectifier and tube-driven reverb. This amp could do it all: pleasant cleans and distortion at both moderate and loud levels. It wouldn’t stay loud and clean, though. For that, we would need a third amp, which we will maybe get back to later.
I’d be excited to hear your thoughts about these amps, and if I should follow my dreams to build themI would use a Pro Reverb-sized 2x12 cabinet for this amp, with the output impedance selector and speaker switches I mentioned earlier. The amp would have dual 6L6s in push/pull, and a Super Reverb-sized 125A9A output transformer for a firm low end at 40-watt power output. I would go for cathode bias in this amp, for a compressed, low-wattage, tweed-style response, to add even more dirt next after the hot preamp section. There is only one jack input into the single channel, with reverb, tremolo, and full EQ controls (bright switch, bass, mid, and treble). Since this would be a more costly amp, I’d use a tube rectifier and tube-driven reverb. This amp could do it all: pleasant cleans and distortion at both moderate and loud levels. It wouldn’t stay loud and clean, though. For that, we would need a third amp, which we will maybe get back to later.
I’d be excited to hear your thoughts about these amps, and if I should follow my dreams to build them!
Over the decades with Hüsker Dü, Sugar, and solo, Bob Mould has earned a reputation for visceral performances.
The 15th studio album from the legendary alt-rocker and former Hüsker Dü singer and 6-stringer is a rhythm-guitar record, and a play in three acts, inspired by sweaty, spilled-beer community connection.
Bob Mould wrote his last album, Blue Heart, as a protest record, ahead of the 2020 American election. As a basic rule, protest music works best when it's shared and experienced communally, where it can percolate and manifest in new, exciting disruptions. But 2020 wasn’t exactly a great year for gathering together.
Mould’s album landed in a world of cloistered listeners, so he never knew how it impacted people. For a musician from punk and hardcore scenes, it was a disquieting experience. So when he got back out on the road in 2023 and 2024, playing solo electric sets, the former Hüsker Dü and Sugar frontman was determined to reconnect with his listeners. After each show, he’d hang out at the merch table and talk. Some people wanted their records or shirts signed, some wanted a picture. Others shared dark stories and secret experiences connected to Mould’s work. It humbled and moved him. “I’m grateful for all of it,” he says.
These are the in-person viscera of a group of people connecting on shared interests, versus, says Mould, “‘I gotta clean the house today, so I’m going to put on my clean the house playlist that a computer designed for me.” “Everything has become so digitized,” he laments. “I grew up where music was religion, it was life, it was essential. When people come to shows, and there’s an atmosphere, there’s volume, there’s spilled drinks and sweat–that’s what music ritual is supposed to be.”
His experiences on tour after the pandemic heartened Mould, but they also gave him traction on new ideas and direction for a new record. He returned to the simple, dirty guitar-pop music that spiked his heart rate when he was young: the Ramones’ stupid-simple pop-punk ecstasy, New York Dolls’ sharp-edged playfulness, Pete Townshend’s epic, chest-rattling guitar theatrics. In other words, the sort of snotty, poppy, wide-open rock we heard and loved on Hüsker Dü’s Flip Your Wig and Candy Apple Grey.
Mould’s time on the road playing solo in 2023 sparked the idea for Here We Go Crazy.
Photo by Ryan Bakerink
Mould started writing new songs in the vein of his original childhood heroes, working them into those electric solo sets in 2023 and 2024. Working with those restraints—guitar chords and vocal melodies—put Mould on track to make Here We Go Crazy, his new, 15th solo record.
Lead single and opener “Here We Go Crazy” is a scene-setting piece of fuzzy ’90s alt-rock, bookended by the fierce pounding of “Neanderthal.” “When Your Heart is Broken” is a standout, with its bubblegum chorus melody and rumbling, tense, Who-style holding pattern before one of the album’s only solos. Ditto “Sharp Little Pieces,” with perhaps the record’s chewiest, darkest guitar sounds.
“It’s a very familiar-sounding record,” he continues. “I think when people hear it, they will go, ‘Oh my god, this is so Bob Mould,’ and a lot of that was [influenced by] spending time with the audience again, putting new stuff into the set alongside the songbook material, going out to the table after the show and getting reactions from people. That sort of steered me towards a very simple, energetic, guitar-driven pop record.”
Of his new album, Mould says, “I think when people hear it, they will go, ‘Oh my god, this is so Bob Mould.’”
Mould recorded the LP in Chicago with longtime bandmates Jason Narducy and Jon Wurster at the late, great Steve Albini’s Electrical Audio. Then Mould retreated to San Francisco to finish the record, chipping away at vocals and extra guitar pieces. He mostly resisted the pull of “non-guitar ornamentation”: “It’s a rhythm guitar record with a couple leads and a Minimoog,” he says. “It’s sort of cool to not have a 64-crayon set every time.”
Mould relied on his favorite, now-signature late-’80s Fender Strat Plus, which sat out on a runway at O’Hare in 20-below cold for three hours and needed a few days to get back in fighting shape. In the studio, he ran the Strat into his signature Tym Guitars Sky Patch, a take on the MXR Distortion+, then onto a Radial JD7. The Radial split his signal and sent it to three combo amps: a Fender Hot Rod DeVille, a Fender ’68 Custom Deluxe Reverb reissue, and a Blackstar Artisan 30, each with a mic on it. The result is a brighter record that Mould says leaves more room for the bass and kick drum. “If you listen to this record against Patch the Sky, for instance, it’s night and day,” he says. “It’s snug.”
Mould explains that the record unfolds over three acts. Tracks one through five comprise the first episode, crackling with uncertainty and conflict. The second, spread over songs six to eight, contrasts feelings of openness with tight, claustrophobic tension. Here, there are dead ends, addictions, and frigid realities. But after “Sharp Little Pieces,” the album turns its corner, barreling toward the home stretch in a fury of optimism and determination. “These last three [songs] should give us more hope,” says Mould. “They should talk about unconditional love.”
The record closes on the ballad “Your Side,” which starts gentle and ends in a rush of smashed chords and cymbals, undoubtedly one of the most invigorating segments. “The world is going down in flames, I wanna be by your side/We can find a quiet place, it doesn’t need to be the Albert Hall,” Mould starts. It’s a beautiful portrait of love, aging, and the passage of time.
Bob Mould's Gear
Mould paired his trusty Fender Strat Plus with a trio of smaller combo amps to carve out a more mid-focused rhythm-guitar sound in the studio.
Photo by Mike White
Guitars
- Late 1980s Fender American Standard Strat Plus (multiple)
Amps
- Fender Hot Rod DeVille
- Blackstar Artisan Series amps
- Fender '68 Custom Deluxe Reverb
Effects
- Tym Guitars Sky Patch
- TC Electronic Flashback
- Electro-Harmonix Freeze
- Wampler Ego
- Universal Audio 1176
- Radial JD7
Strings, Picks, & Power Supply
- D'Addario NYXLs (.011-.046)
- Dunlop .46 mm and .60 mm picks
- Voodoo Labs power supply
And though the record ends on this palette of tenderness and connection, the cycle is likely to start all over again. Mould understands this; even though he knows he’s basking in act three at the moment, acts one and two will come along again, and again. Thankfully, he’s figured out how to weather the changes.
“When things are good, enjoy them,” he says. “When things are tough, do the work and get out of it, somehow.”
- YouTube
Many of the tracks on Here We Go Crazy were road-tested by Mould during solo sets. Here, accompanied only by his trusty Fender Strat, he belts “Breathing Room.”
Reader: Federico Novelli
Hometown: Genoa, Italy
Guitar: The Italian Hybrid
Reader Federico Novelli constructed this hybrid guitar from three layers of pine, courtesy of some old shelves he had laying around.
Through a momentary flash, an amateur Italian luthier envisioned a hybrid design that borrowed elements from his favorite models.
A few years ago, at the beginning of Covid, an idea for a new guitar flashed through my mind. It was a semi-acoustic model with both magnetic and piezo pickups that were mounted on a soundboard that could resonate. It was a nice idea, but I also had to think about how to make it in my tiny cellar without many power tools and using old solid-wood shelves I had available.
I have been playing guitar for 50 years, and I also dabble in luthiery for fun. I have owned a classical guitar, an acoustic guitar, and a Stratocaster, but a jazz guitar was missing from the list. I wanted something that would have more versatility, so the idea of a hybrid semi-acoustic guitar was born.
I started to sketch something on computer-aided design (CAD) software, thinking of a hollowbody design without a center block or sides that needed to be hot-worked with a bending machine. I thought of a construction made of three layers of solid pine wood, individually worked and then glued together in layers, with a single-cutaway body and a glued-in neck.
For the soundboard and back, I used a piece of ash and hand-cut it with a Japanese saw to the proper thickness, so I had two sheets to fit together. Next, I sanded the soundboard and bottom using two striker profiles as sleds and an aluminum box covered in sandpaper to achieve a uniform 3 mm thickness. A huge amount of work, but it didn't cost anything.
“It was a nice idea, but I also had to think about how to make it in my tiny cellar without many electric tools and out of old solid-wood shelves I had available.”
The soundboard has simplified X-bracing, a soundhole with a rosewood edge profile, and an acoustic-style rosewood bridge. For the neck, I used a piece of old furniture with straight grain, shaped it to a Les Paul profile, and added a single-action truss rod. The only new purchase: a cheap Chinese rosewood fretboard.
Then, there was lots of sanding. I worked up to 400-grit, added filler, primer, and transparent nitro varnish, worked the sandpaper up to 1,500-grit, and finally polished.
Our reader and his “Italian job.”
For electronics, I used a Tonerider alnico 2 humbucker pickup and a piezo undersaddle pickup, combined with a modified Shadow preamp that also includes a magnetic pickup input, so you can mix the two sources on a single output. I also installed a bypass switch for power on/off and a direct passive output.
I have to say that I am proud and moderately satisfied both aesthetically and with the sounds it produces, which range from jazz to acoustic and even gypsy jazz. However, I think I will replace the electronics and piezo with Fishman hardware in the future.