
Looking for more classic growl in a simple, contemporary overdrive? CopperSound’s Alex Guaraldi explains how to swap the clipping LEDS in an ultra-affordable EarthQuaker Devices Plumes for germanium diodes, in nine easy steps.
Pedals offer a lot of opportunities for DIY projects. One of the coolest and easiest is removing the LED clipping diodes in a modern overdrive pedal and replacing them with old-school-sounding germanium ones. The result will be a more raw, aggressive tone. For this project, I used the popular and affordable EarthQuaker Devices Plumes ($99 street). Whether your version is the original with through-hole-type components or the current model with surface-mount components, you’ll easily be able to perform this mod because both versions contain through-hole-type LEDs.
Tools Required
These tools and supplies are available online. StewMac, for example, sells soldering irons, a desoldering pump, and other tools for instrument work, while nut drivers and germanium diodes can be acquired via a number of sources, including Amazon.
• Soldering iron
• Solder
• Desoldering pump
• No. 2 Phillips-head screwdriver
• Small flathead screwdriver
• 8 mm (5/16") nut driver/wrench
• 10 mm (25/64") nut driver/wrench
• 11 mm (7/16") nut driver/wrench
• 14 mm(9/16") wrench
• Flush cutters
• Small needle-nose pliers
• Germanium diodes
Step 1: Remove back cover.
Using a No. 2 Phillips-head screwdriver, remove the four screws holding the back cover on.
Step 2: Remove external hardware.
The fastest way to swap diodes may be to do it from the component side, without even removing the circuit board from the enclosure. But for easier access and less difficulty, I’m going to remove the entire printed circuit board (PCB) from the enclosure. Since almost everything is mounted directly to the PCB, this should be easy.
Using a small flathead screwdriver, remove the knobs from the potentiometer shafts. Only loosen the knob set screws enough to slide the knobs off. No need to be searching the floor for tiny screws.
Next, using an 8 mm (5/16") nut driver or wrench, remove the nut from the toggle switch. Then, using a 10 mm (25/64”) nut driver or wrench, remove the three nuts and washers from the potentiometers.
Photo 1
For the last piece of external hardware located on the face—the footswitch—we’ll actually want to go inside and disconnect its plug from the board.
On the bottom left side of the PCB, there will be a white rectangular connector. We need to unplug the female end from the male end. This is where small needle-nose pliers can help. A small screwdriver or even fingers may do the trick, too. Finesse is key. We don’t want to break the wires from the female connector.
Photo 2
Once dislocated, we can go back to the face and remove the footswitch using a 14 mm (9/16") wrench.
Step 3: Remove external hardware on the back heel.
The last external hardware to remove is the audio jack bushings.
Photo 3
Removing these will allow the PCB to slide out of the enclosure. Using an 11mm (7/16") nut driver or wrench, remove the bushings and beveled washers from the audio jacks. Now, the circuit board is free to be removed from the enclosure.
Step 4: Remove the PCB from the enclosure.
The four controls and two audio jacks that interface with the enclosure may create some resistance when trying to remove the PCB. Typically, it’s from the collars of the audio jacks. Using a small screwdriver in one of the top corners and gently prying the PCB back usually does the trick.
Photo 4
Step 5: Locating the clipping LEDs.
Now that the PCB is removed from the enclosure, we need to locate the clipping LEDs from the top side. They are the two small red silos at the center of the pedal.
Photo 5
Then, we need to locate the pads (the exposed metal on the PCB) for them on the bottom side, and, once again, they are centrally located.
Photo 6
Step 6: Removing the clipping LEDs.
Now that we’ve located the LEDs, let’s go ahead and remove them. Quick note: The Plumes I worked on was a new unit consisting primarily of surface mount device (SMD) components. The LEDs are located between the pots and switch, so they can be difficult to access from the bottom side. The easiest way to remove the LEDs is to actually snip them from the top side, after noting how they are soldered in place.
Photo 7
We’re not planning on using them, and they’re cheap enough to purchase again, so breaking them is no worry. We just need to be sure not to damage any of the nearby components. The best approach may be to break the shell/bulb of the LEDs. Doing this will expose the two leads.
Photo 8
With these two leads exposed, we can easily remove each lead from the solder pads on the top side. Let’s apply heat to each pad and remove the leads with small needle-nose pliers. Jump to the alternate approach section in step seven if you experience solder removal difficulties. (Quick tips: Existing solder tends to flow better when a bit of fresh solder is applied to it. You’ll also want to heat the lead/pad and then grab the lead with the pliers. Grabbing the lead with the pliers first will take longer because the heat will transfer to the metal of the pliers. Don’t apply heat to a solder pad longer than needed. Doing this can compromise the pad.)
Once the leads are removed, we need to remove the remaining solder from the pads. This is where the desoldering pump (commonly referred to as a “solder sucker”) comes in. Apply a bit of fresh solder to the pads and remove it using the pump. YouTube is your friend here, for some quick desoldering pump lessons.
Step 7: Adding germanium diodes.
Check the polarity of the diode. For this mod, I chose 1n34a diodes, which are very common and available on Amazon. These diodes are polarized and have a positive and negative side. On the 1n34a, the negative lead is designated by the black band that wraps around the body of the diode (this is not the case for all germanium diodes). On PCBs, square pads denote positive. However, for the diode package that we’re adding, the square pad is negative.
Photo 9
Using Photo 10 for reference, gently bend one of the diode legs so that it’s parallel with the body of the diode. Place the bent legs into their correct pads—the negative side of the diode will go into the square pad and the positive into the circlular pad. Solder the pads from the bottom side of the PCB and snip the excess leg length with a pair of flush cutters. The excess leg length can also be removed with needle-nose pliers by bending the legs back and forth several times.
Photo 10
Alternate approach: If you’re experiencing trouble getting the remaining solder out of each pad, there’s a different approach to try. This approach may actually be helpful for this particular mod, because the pad spacing is small. If a pad connects to a ground plane (a layer of copper typically the size of the entire PCB that connects directly to the main ground pin on the DC jack) or several locations (other components in the schematic) it will require more heat because the applied heat wants to travel to all the connected areas. Typically, with clipping diodes, only one pad will experience this and give desoldering difficulties. In such a case, follow these steps:
1. Establish which pad has remaining solder. For this mod, the square pads are the positive pads, because they hosted LEDs. The diodes we’re adding want to have the negative side go into the square pad.
2. Cut the negative side of the germanium diode lead down to about 5 mm length. The negative side on the 1n34a is the lead closest to the black line indicator seen in Photo 9.
3. Heat the pad that has remaining solder in it and drop the short side lead into the solder.
4. Bend the other lead over like a horseshoe and mate it with the desoldered pad. (See Photo 10)
5. Solder the second side.
6. Repeat for the second diode, keeping in mind that the polarity of the diode needs to be opposite of the first diode that we soldered in as seen in Photo 11.
Photo 11
Step 8: Test.
Before putting everything back together, plugging the unit in as-is can be helpful. This way, if it isn’t working, we can go back and look at solder joints and any potential issues.
Photo 12
Step 9: Put everything back together.
Simply reverse the disassembly steps and enjoy!
A final note: If you love DIY projects or are interested in learning pedal design, my company, CopperSound, has a DIY section on its website, which also includes links to other DIY dealers. We offer integrated breadboards, component substitution boxes, adaptors for toggle switches, and even solder dispensers. For more information, please check out coppersoundpedals.com/DIYFeaturing torrefied solid Sitka Spruce tops, mahogany neck, back, and sides, and Fishman Presys VT EQ System, these guitars are designed to deliver quality tone and playability at an affordable price point.
Cort Guitars, acclaimed for creating instruments that exceed in value and quality, introduces the Essence Series. This stunning set of acoustic guitars is designed for musicians looking for the quintessential classic acoustic guitar with fabulous tone all at an exceptional price point. The Essence Series features two distinct body shapes: The Grand Auditorium and the OM Cutaway. Whatever the flavor, the Essence Series has the style to suit.
The Essence-GA-4 is the perfect Grand Auditorium acoustic. Wider than a dreadnought, the Essence-GA-4 features a deep body with a narrower waist and a width of 1 ¾” (45mm) at the nut. The result is an instrument that is ideal for any number of playing styles: Picking… strumming… the Essence GA-4 is completely up for the task.
The Essence-OM-4 features a shallower body creating a closer connection to the player allowing for ease of use on stage. With its 1 11/16’th (43mm) nut width, this Orchestra Model is great for fingerpickers or singer/guitarists looking for better body contact for an overall better playing experience.
Both acoustics are topped with a torrefied solid Sitka Spruce top using Cort’s ATV process. The ATV process or “Aged to Vintage”, “ages” the Spruce top to give it the big and open tone of older, highly-sought-after acoustics. To further enhance those vintage tones, the tops bracing is also made of torrefied spruce. The mahogany neck, back, and sides create a warm, robust midrange and bright highs. A rosewood fingerboard and bridge add for a more balanced sound and sustain. The result is amazing tone at first strum. 18:1 Vintage Open Gear Tuners on the mahogany headstock offer precise tuning with vintage styling. The herringbone rosette & purfling accentuates the aesthetics of these instruments adding to their appeal. Both acoustics come in two choices of finish. Natural Semi-Gloss allows the Sitka spruce’s natural beauty to shine through and classic Black Top Semi-Gloss.
A Fishman® Presys VT EQ System is installed inside the body versus other systems that cut into the body to be installed. This means the instrument keeps its natural resonance and acoustic flair. The Presys VT EQ System keeps it simple with only Volume and Tone controls resulting in a true, crisp acoustic sound. Lastly, Elixir® Nanoweb Phosphor Bronze Light .012-.053 Acoustic Strings round out these acoustics. This Number 1 acoustic guitar string delivers consistent performance and extended tone life with phosphor bronze sparkle and warmth. The Essence Series takes all these elements, combines them, and exceeds in playability, looks, and affordability.
Street Price: $449.00
For more information, please visit cortguitars.com.
Cort Essence-GA4 Demo - YouTube
Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.Moth Electric's C. regalis overdrive pedal offers massive boost, natural overdrive, and searing distortion for guitar and bass. With active treble and bass controls, clean blend, Smooth/Crunch modes, and true-bypass switching, this USA-made pedal is a versatile addition to any pedalboard.
Adding a new model to their line of overdrives, Moth Electric has released the C. regalis. Equally suited for guitar and bass, the meticulously designed C.regalis is capable of massive boost, natural, singing overdrive, and searing mid-gain distortion. Its six op-amps power a dynamic, crunchy overdrive circuit with a suite of features including:
- Active treble and bass controls that allow for +/- 15db boost and cut. Perfect for tailoring the C. regalis to your instrument and amp.
- A powerful clean blend for introducing either your amp’s natural character or another effect into the equation. Allows the C. regalis to become a more transparent overdrive.
- Smooth/Crunch modes, provide a subtle change in feel with ‘Smooth’ increasing sustain and ‘Crunch’ introducing high-order harmonics for additional texture.
The C. regalis offers the following features:
- Bass, Treble, Blend, Volume, Drive controls
- Smooth/Crunch modes● More volume than you’ll ever need
- True-bypass switching, top-mounted jacks for easy placement on crowded pedalboards
- 9-volt DC operation with external power supply – no battery compartment
- Designed and hand-built in the USA using through-hole components
The C. regalis carries a $179.99 price and is available for purchase at mothelectric.com.
For more information, please visit mothelectric.com.
OK WOW. Moth Electric C.REGALIS - Pedals and Tea EP 57 - YouTube
Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.Jack White's 2025 No Name Tour features live tracks from his album No Name, with shows across North America, Europe, the UK, and Japan.
The EP is a 5-song collection of live tracks taken from White’s 2024 edition of the tour, which was characterized by surprise shows in historic clubs around the world to support the 2024 album No Name.
No Name is available now via Third Man Records. The acclaimed collection was recently honored with a 2025 GRAMMY® Award nomination for “Best Rock Album” – White’s 34th solo career nomination and 46th overall along with 16 total GRAMMY® Award wins. The No Name Tour began, February 6, with a sold-out show at Toronto, ON’s HISTORY and then travels North America, Europe, the United Kingdom, and Japan through late May. For complete details and remaining ticket availability, please visit jackwhiteiii.com/tour-dates.
White’s sixth studio album, No Name officially arrived on Friday, August 2 following its clandestine white-label appearance at Third Man Records locations that saw customers slipped, guerilla-style, free unmarked vinyl copies in their shopping bags. True to his DIY roots, the record was recorded at White’s Third Man Studio throughout 2023 and 2024, pressed to vinyl at Third Man Pressing, and released by Third Man Records.
For more information, please visit jackwhiteiii.com.
JACK WHITE - NO NAME TOUR 2025
FEBRUARY
11 – Brooklyn, NY – Kings Theatre
12 – Brooklyn, NY – Brooklyn Paramount
17 – Boston, MA – Roadrunner
18 – Boston, MA – Roadrunner
21 – Paris, France – La Cigale
22 – Paris, France – La Trianon
23 – Paris, France – La Trianon
25 – Utrecht, Netherlands – TivoliVredenburg (Ronda)
26 – Utrecht, Netherlands – TivoliVredenburg (Ronda)
28 – London, UK – Troxy
MARCH
1 – London, UK – Troxy
2 – Birmingham, UK – O2 Academy Birmingham
3 – Glasgow, UK – Barrowland Ballroom
10 – Hiroshima, Japan – Blue Live Hiroshima
12 – Osaka, Japan – Gorilla Hall
13 – Nagoya, Japan – Diamond Hall
15 – Tokyo, Japan – Toyosu PIT
17 – Tokyo, Japan – Toyosu PIT
APRIL
3 – St. Louis, MO – The Factory
4 – Kansas City, MO – Uptown Theater
5 – Omaha, NE – Steelhouse Omaha
7 – Saint Paul, MN – Palace Theatre
8 – Saint Paul, MN – Palace Theatre
10 – Chicago, IL – The Salt Shed (Indoors)
11 – Chicago, IL – The Salt Shed (Indoors)
12 – Detroit, MI – Masonic Temple Theatre
13 – Detroit, MI – Masonic Temple Theatre
15 – Grand Rapids, MI – GLC Live at 20 Monroe
16 – Cleveland, OH – Agora Theatre
18 – Nashville, TN – The Pinnacle
19 – Nashville, TN – The Pinnacle
MAY
4 – Austin, TX – ACL Live at the Moody Theater
5 – Austin, TX – ACL Live at the Moody Theater
6 – Dallas, TX – South Side Ballroom
8 – Denver, CO – Mission Ballroom
9 – Denver, CO – Mission Ballroom
10 – Salt Lake City, UT – The Union Event Center
12 – Los Angeles, CA – Hollywood Palladium
13 – Los Angeles, CA – Hollywood Palladium
15 – Santa Barbara, CA – Santa Barbara Bowl
16 – Oakland, CA – Fox Theater
17 – San Francisco, CA – The Masonic
19 – Seattle, WA – The Paramount Theatre
20 – Seattle, WA – The Paramount Theatre
22 – Vancouver, BC – Commodore Ballroom
23 – Vancouver, BC – Commodore Ballroom
24 – Troutdale, OR – Edgefield Concerts on the Lawn
A dose of magic gain potion.
Works like a little vial of magic gain potion. Fattens without obscuring individual frequency bands.
None.
$129
Solodallas SVDS Boost
solodallas.com
The Schaeffer-Vega Diversity System—an early and very successful wireless system—excelled at the tasks it was designed for. But there was more magic than met the eye. Though designed to sound as transparent as possible, it nonetheless colored the signal in a way that people like Angus Young and Eddie Van Halen found essential.
SoloDallas explored the possibilities of this circuit before in pedals like theSchaeffer Replica, but the new SVDS Boost strips the formula to essentials. Minimalist controls—one knob, that’s it—make this boost no less delicious. I’m not surprised Angus Young was smitten with the original SVDS. An SG and Marshall 18-watt amp sound fantastic naked, but the SVDS Boost has the rare talent for fattening everything without seeming to favor or obscure any frequency band too much. And as zest to the PAF/Marshall style formula, it makes the kind of rowdy, organic, airy, large, and punch-packing Marshall sound you would dream of getting in a studio or hearing on the radio. There are many shades of this basic awesome color in spite of the single knob. Unity gain lives in the earliest third of its range. From there you certainly get more volume, but mostly you bathe in various hues of compressed, saturated, thick, and dynamite growl. You don’t need a Gibson and a Marshall to use it to devastating effect, either. A Telecaster and Vibrolux snap with attitude and whip-crack energy with the SVDS in the line. And with both guitar/amp combos, the SVDS’ wide dynamic responsiveness to volume and tone attenuation assures that things stay cracking when you need more control.