Hard-hitting, dance-punk duo Death From Above 1979 takes production into its own hands and delivers an onslaught of noisy dance mayhem on Is 4 Lovers.
For brash Canadian rock 'n' roll duo Death From Above 1979, the road to maximum impact has always been paved with as few elements as possible: drums, vocals, a bit of synth, and some wildly athletic and fuzzed-out bass guitar.
Bassist Jesse Keeler and drummer/vocalist Sebastien Grainger came out of the gate swinging in 2004 with their debut LP, You're a Woman, I'm a Machine, a record that proved the band's mix of unexpectedly sparse instrumentation, danceable rhythms, highwire vocals, and grimy, hardcore punk sonics to be a tremendously compelling sound. The duo imploded shortly after that album's release, but the waves created on that record would ripple long after the split as DFA 1979's legend grew.
Death From Above 1979 - One + One (Official Music Video)
When Keeler and Grainger regrouped in 2011 and set about recording their sophomore effort, The Physical World, there was tremendous pressure to nurture and preserve the sound of that first album in order to avoid alienating the fanbase they'd harnessed in their time away. Keeler explains, "When we started playing again in 2011, this idea of Death From Above was an external thing that had lived without us, so we came back to it not wanting to screw that up. We were working in service to this thing that had lived without us. That's exactly how the producers felt, so we had those producers to keep us being that band."
The Physical World, produced by Dave Sardy, made good on the band's intentions to hone the brutal dance-punk sound that made the band's debut such a smash, and the group's 2017 Eric Valentine–produced effort, Outrage! Is Now, opted to stick to a similar program. Rather than tread water for a fourth release, DFA 1979 has returned with a decidedly playful new record entitled Is 4 Lovers, which brings a new, defiant flavor to the band's discography.
"I have riff diarrhea. I have riff IBS and I just can't shut it off!" —Jesse Keeler
Is 4 Lovers takes listeners on a turbulent trip straight to the center of Keeler and Grainger's musical psyche. The record feels not unlike a sweaty, blistering live set as their dancy churn and gritty sonics remain intact, especially on tracks such as "Totally Wiped Out," and the two-part "N.Y.C. Power Elite." Elsewhere, songs like "Glass Homes" and "No War" show a new level of maturity in the band's sound as the combative edge that lined their past efforts has been replaced by a heavier dose of melody and a more thoughtful use of effects and synths.
This time around, Keeler and Grainger decided it was time to take production duties into their own hands. As a result, Is 4 Lovers may be the purest expression of what DFA 1979 is about since their debut.
Jesse Keeler's Dan Armstrong Lucite basses are all outfitted with custom pickups made by Kent Armstrong, son of Dan Armstrong. Keeler also swaps out the original fixed rosewood bridges for custom brass units milled by Canadian luthier Les Godfrey.
Photo by Debi Del Grande
Frustrated with how other producers changed their sound in the past, Keeler explains their decision: "We wanted to make it really apparent on this album that you're listening to the band—just the two of us. Part of being in a two-piece 20 years ago was dealing with people in the music business who thought it was a bad idea. They liked the music, but they thought it would need help. Producers always wanted to pad up the sound. It's not a knock to anyone we've worked with in the past, but if you're someone that's mixed all these records where the guitar is a really important thing and we ask them to do the same thing with our sound but without the tools they're used to working with, it can be tough. Doing it all ourselves, we don't have those hang-ups and we never come at it thinking there's this hole we have to fill in our sound."
The duo still makes a hell of a lot of noise on Is 4 Lovers, even without a producer pushing them to pad their sound with additional instrumentation. As longtime fans will expect, Keeler's bass tones kick the listener in the jaw with plenty of the square-wave filth he's reveled in since DFA 1979's inception. However, his rig has changed dramatically for the first time in the band's history. Rather than plugging into his trusted backline of a vintage Peavey Super Festival F-800B and an Acoustic 450 head—a pair of amps which Keeler has always described as defining elements of the band's sound—the bassist tracked his parts with a pair of Orange Bax Bangeetar preamp/EQ pedals that he modified himself.
TIDBIT: Death From Above 1979's fourth studio album, Is 4 Lovers, was entirely written and produced by band members Jesse Keeler and Sebastien Grainger and recorded all in one room.
Why the change after so many years? Part of it was the need to sidestep the isolation headaches of miking loud amps while the duo tracked Is 4 Lovers live, together in one room. But Keeler also found the modded Bax Bangeetars remedied some things he always disliked about his tone."The old rig sounded good through the monitors," he says, "but it had the same issues I've always had with it. I love how all the 300-500 Hz stuff sounds through the amps but recorded it can come out as mud and there's always some loss of clarity, especially when I'm competing with tones in the drums."
The Bax Bangeetars provided an ideal surrogate for the old amps, but not without a bit of tinkering from the tech-savvy bassist, who explains his handiwork: "Those pedals are a very simple circuit, but they have this power pump that takes the 9 volts in and charges up the cap, which slowly releases it at 24 volts. I found at high gain, even with the highest milliamp 9V power supply I could find, it couldn't keep the cap filled up fast enough. I had these science-grade variable power supplies and, if you wire around the pedal's stock power supply so that you can feed that cap directly, then you don't get that headroom loss at all and it sounds really good."
Jesse Keeler's Gear
Basses
- Ampeg Dan Armstrong Lucite basses (modified with custom Kent Armstrong pickups and brass bridges made by luthier Les Godfrey)
Amps
- Orange Bax Bangeetar Guitar Preamp & EQ (modified by Keeler)
Strings and Picks
- Ernie Ball Regular Slinky Nickel Wound Electric Bass Strings (.050–.105)
- Dunlop .73 mm Tortex Triangle
Effects
- Death By Audio Echo Dream 2
- Death By Audio Fuzz War
- EarthQuaker Devices Bit Commander
- FoxRox Octron3
- Ibanez CS9 Stereo Chorus
- MXR Ten Band EQ
- Overstayer Modular Channel Stereo 8755D
Keeler says that increased headroom has long been a special ingredient to his tone and adds, "The secret with my Peavey F-800B head and part of the reason why it's so special is that it's running on 36 volts. The schematic for that Peavey amp says 24 volts, so whenever anyone would clone the circuit, they'd do it to run on 24 volts and, when you try to play it like I do with the distortion cranked up to 10, it starts self-compressing and crapping out!"
Despite the major shakeup in Keeler's amp world, the bassist's primary muse remains his small collection of vintage Ampeg Dan Armstrong Lucite basses. Thanks to their skinny neck profile, short scale length, and easy access to all 24 frets, the bassist credits these instruments with unlocking his unconventionally athletic playing style in which he bends strings and frequently combines droning open notes with guitar-lead-like riffs that he plays simultaneously in the upper frets.
While these basses are a great fit for Keeler, he's found some need for modifications. All of his Dan Armstrong basses have been re-fretted with wider fretwire and outfitted with custom pickups made by Kent Armstrong, son of Dan Armstrong. The most important mod that Keeler does to all of his basses is to swap out the original fixed rosewood bridges for custom brass units milled by Canadian luthier Les Godfrey. Godfrey's bridges have fully adjustable saddles, which makes life a lot easier as Keeler used to struggle with the original bridge's intonation issues.
Jesse Keeler mainly sticks to his modded Dan Armstrong basses, but he also has several custom Rickenbacker 4030 models.
Photo by Jim Bennett
The brass bridges also offer an important tonal benefit. "The overall problem with that bass is that it sounds like talking with your hand over your mouth; it's a very muffled, low/mid sound with not enough brilliance, even with brand new strings on it," Keeler says. "I wanted as much bright attack as I could get out of it. When playing notes in quick succession, I want the initial attack of the note to be very present, so brass saddles and brass nuts really help with that." These modifications take a lot of effort, but he adds, "I did all this work to make them right because I love them so much."
For effects, Keeler pulled his usual pedalboard apart and got experimental in the studio. A pair of Foxrox Octron3 octave pedals appear on nearly every track, with each one sent to their own Bax Bangeetar and set to accentuate slightly different frequencies. The bassist also frequently called upon a Death By Audio Fuzz War but claims to have had the fuzz control barely on, using the pedal more for its powerful filter than its heaps of gain. One of the most vicious tones on Is 4 Lovers can be heard on "N.Y.C. Power Elite Part II," which he happened upon by plugging into an EarthQuaker Devices Bit Commander and turning the volume on his bass down to the point where it began to starve the synth box of enough signal to track its multiple octaves properly.
Bassist Jesse Keeler says he and drummer/vocalist Sebastien Grainger no longer have to talk about writing: They simply feel it out and intuitively know when an idea has clicked. Their shared killer instincts are palpable onstage.
Photo by Debi Del Grande
Songwriting is a collaborative process for DFA 1979, and something the duo has fine-tuned over the course of their discography. Keeler admits, "I don't really think of myself as a songwriter, I just vomit out riffs," he says. "I have riff diarrhea. I have riff IBS and I just can't shut it off!" He goes on to explain, "I try to distill my ideas down to make things musical enough that Sebastien can sing over, because he wants a melody. I've given him things in the past that became very hard to find a melody for because I would write things that you could only scream over," he says. "Sebastien is the one that moved me towards making songs and not just trying to create a feeling."
On Is 4 Lovers, the writing process came from shared instinct rather than intellect. Keeler says he and Grainger no longer have to talk about writing, they simply feel it out and intuitively know when an idea has clicked. "We made this record entirely within one room," Keeler says. "We'd hit record the minute we got there and play through the day, so a lot of what you hear on the record is the actual creation of those parts the moment they were made up. I'm really into that immediacy."
This method of writing and recording allowed the band to deliver a tight and focused record that totally aligns with how Keeler and Grainger want DFA 1979 to sound. "I think the results are amazing and I think this is the best sounding record we've made," the bassist says. "Not to take anything away from anyone we've worked with in the past, but this one sounds the most right to me because it's all us."
Death From Above 1979 - Holy Books (Live in Toronto)
Jesse Keeler's bass tone will explode from your speakers in this live version of "Holy Books" from Death From Above 1979's Outrage! Is Now. The bassist's heavily distorted riffs pummel along with Sebastien Grainger's hard-hitting grooves throughout the song's main sections, while he conjures a just-on-the-verge-of-feedback tone for the melodic breakdown starting at 2:23.
- Best Albums of 2020 - Premier Guitar ›
- Death from Above's Jesse Keeler: Like an Ant Looking at the Moon ... ›
- Rig Rundown: Death From Above 1979 - Premier Guitar ›
Selenium, an alternative to silicon and germanium, helps make an overdrive of great nuance and delectable boost and low-gain overdrive tones.
Clever application of alternative materials that results in a simple, make-everything-sound-better boost and low-gain overdrive.
Might not have enough overdrive for some tastes (although that’s kind of the idea).
$240 street
Cusack Project 34 Selenium Rectifier Pre/Drive Pedal
cusackmusic.com
The term “selenium rectifier” might be Greek to most guitarists, but if it rings a bell with any vintage-amp enthusiasts that’s likely because you pulled one of these green, sugar-cube-sized components out of your amp’s tube-biasing network to replace it with a silicon diode.
That’s a long-winded way of saying that, just like silicon or germanium diodes—aka “rectifiers”—the lesser-seen selenium can also be used for gain stages in a preamp or drive pedal. Enter the new Project 34 Selenium Rectifier Pre/Drive from Michigan-based boutique maker Cusack, named after the element’s atomic number, of course.
An Ounce of Pre-Vention
As quirky as the Project 34 might seem, it’s not the first time that company founder Jon Cusack indulged his long-standing interest in the element. In 2021, he tested the waters with a small 20-unit run of the Screamer Fuzz Selenium pedal and has now tamed the stuff further to tap levels of gain running from pre-boost to light overdrive. Having used up his supply of selenium rectifiers on the fuzz run, however, Cusack had to search far and wide to find more before the Project 34 could launch.
“Today they are usually relegated to just a few larger industrial and military applications,” Cusack reports, “but after over a year of searching we finally located what we needed to make another pedal. While they are a very expensive component, they certainly do have a sound of their own.”
The control interface comprises gain, level, and a traditional bright-to-bassy tone knob, the range of which is increased exponentially by the 3-position contour switch: Up summons medium bass response, middle is flat response with no bass boost, and down is maximum bass boost. The soft-touch, non-latching footswitch taps a true-bypass on/off state, and power requires a standard center-negative 9V supply rated at for least 5 mA of current draw, but you can run the Project 34 on up to 18V DC.
Going Nuclear
Tested with a Telecaster and an ES-355 into a tweed Deluxe-style 1x12 combo and a 65 Amps London head and 2x12 cab, the Project 34 is a very natural-sounding low-gain overdrive with a dynamic response and just enough compression that it doesn’t flatten the touchy-feely pick attack. The key adjectives here are juicy, sweet, rich, and full. It’s never harsh or grating.
“The gain knob is pretty subtle from 10 o’clock up, which actually helps keep the Project 34 in character.”
There’s plenty of output available via the level control, but the gain knob is pretty subtle from 10 o’clock up, which actually helps keep the Project 34 in character. Settings below there remain relatively clean—amp-setting dependent, of course—and from that point on up the overdrive ramps up very gradually, which, in amp-like fashion, is heard as a slight increase in saturation and compression. The pedal was especially fantastic with the Telecaster and the tweed-style combo, but also interacted really well with humbuckers into EL84s, which certainly can’t be said for all overdrives.
The Verdict
Although I almost hate to use the term, the Project 34 is a very organic gain stage that just makes everything sound better, and does so with a selenium-driven voice that’s an interesting twist on the standard preamp/drive. For all the variations on boost and low/medium-gain overdrive out there it’s still a very welcome addition to the market, and definitely worth checking out—particularly if you’re looking for subtler shades of overdrive.
You may know the Gibson EB-6, but what you may not know is that its first iteration looked nothing like its latest.
When many guitarists first encounter Gibson’s EB-6, a rare, vintage 6-string bass, they assume it must be a response to the Fender Bass VI. And manyEB-6 basses sport an SG-style body shape, so they do look exceedingly modern. (It’s easy to imagine a stoner-rock or doom-metal band keeping one amid an arsenal of Dunables and EGCs.) But the earliest EB-6 basses didn’t look anything like SGs, and they arrived a full year before the more famous Fender.
The Gibson EB-6 was announced in 1959 and came into the world in 1960, not with a dual-horn body but with that of an elegant ES-335. They looked stately, with a thin, semi-hollow body, f-holes, and a sunburst finish. Our pick for this Vintage Vault column is one such first-year model, in about as original condition as you’re able to find today. “Why?” you may be asking. Well, read on....
When the EB-6 was introduced, the Bass VI was still a glimmer in Leo Fender’s eye. The real competition were the Danelectro 6-string basses that seemed to have popped up out of nowhere and were suddenly being used on lots of hit records by the likes of Elvis, Patsy Cline, and other household names. Danos like the UB-2 (introduced in ’56), the Longhorn 4623 (’58), and the Shorthorn 3612 (’58) were the earliest attempts any company made at a 6-string bass in this style: not quite a standard electric bass, not quite a guitar, nor, for that matter, quite like a baritone guitar.
The only change this vintage EB-6 features is a replacement set of Kluson tuners.
Photo by Ken Lapworth
Gibson, Fender, and others during this era would in fact call these basses “baritone guitars,” to add to our confusion today. But these vintage “baritones” were all tuned one octave below a standard guitar, with scale lengths around 30", while most modern baritones are tuned B-to-B or A-to-A and have scale lengths between 26" and 30".)
At the time, those Danelectros were instrumental to what was called the “tic-tac” bass sound of Nashville records produced by Chet Atkins, or the “click-bass” tones made out west by producer Lee Hazlewood. Gibson wanted something for this market, and the EB-6 was born.
“When the EB-6 was introduced, the Bass VI was still a glimmer in Leo Fender’s eye.”
The 30.5" scale 1960 EB-6 has a single humbucking pickup, a volume knob, a tone knob, and a small, push-button “Tone Selector Switch” that engages a treble circuit for an instant tic-tac sound. (Without engaging that switch, you get a bass-heavy tone so deep that cowboy chords will sound like a muddy mess.)
The EB-6, for better or for worse, did not unseat the Danelectros, and a November 1959 price list from Gibson hints at why: The EB-6 retailed for $340, compared to Dano price tags that ranged from $85 to $150. Only a few dozen EB-6 basses were shipped in 1960, and only 67 total are known to have been built before Gibson changed the shape to the SG style in 1962.
Most players who come across an EB-6 today think it was a response to the Fender Bass VI, but the former actually beat the latter to the market by a full year.
Photo by Ken Lapworth
It’s sad that so few were built. Sure, it was a high-end model made to achieve the novelty tic-tac sound of cheaper instruments, but in its full-voiced glory, the EB-6 has a huge potential of tones. It would sound great in our contemporary guitar era where more players are exploring baritone ranges, and where so many people got back into the Bass VI after seeing the Beatles play one in the 2021 documentary, Get Back.
It’s sadder, still, how many original-era EB-6s have been parted out in the decades since. Remember earlier when I wrote that our Vintage Vaultpick was about as original as you could find? That’s because the model’s single humbucker is a PAF, its Kluson tuners are double-line, and its knobs are identical to those on Les Paul ’Bursts. So as people repaired broken ’Bursts, converted other LPs to ’Bursts, or otherwise sought to give other Gibsons a “Golden Era” sound and look ... they often stripped these forgotten EB-6 basses for parts.
This original EB-6 is up for sale now from Reverb seller Emerald City Guitars for a $16,950 asking price at the time of writing. The only thing that isn’t original about it is a replacement set of Kluson tuners, not because its originals were stolen but just to help preserve them. (They will be included in the case.)
With so few surviving 335-style EB-6 basses, Reverb doesn’t have a ton of sales data to compare prices to. Ten years ago, a lucky buyer found a nearly original 1960 EB-6 for about $7,000. But Emerald City’s $16,950 asking price is closer to more recent examples and asking prices.
Sources: Prices on Gibson Instruments, November 1, 1959, Tony Bacon’s “Danelectro’s UB-2 and the Early Days of 6-String Basses” Reverb News article, Gruhn’s Guide to Vintage Guitars, Tom Wheeler’s American Guitars: An Illustrated History, Reverb listings and Price Guide sales data.
An '80s-era cult favorite is back.
Originally released in the 1980s, the Victory has long been a cult favorite among guitarists for its distinctive double cutaway design and excellent upper-fret access. These new models feature flexible electronics, enhanced body contours, improved weight and balance, and an Explorer headstock shape.
A Cult Classic Made Modern
The new Victory features refined body contours, improved weight and balance, and an updated headstock shape based on the popular Gibson Explorer.
Effortless Playing
With a fast-playing SlimTaper neck profile and ebony fretboard with a compound radius, the Victory delivers low action without fret buzz everywhere on the fretboard.
Flexible Electronics
The two 80s Tribute humbucker pickups are wired to push/pull master volume and tone controls for coil splitting and inner/outer coil selection when the coils are split.
For more information, please visit gibson.com.
Gibson Victory Figured Top Electric Guitar - Iguana Burst
Victory Figured Top Iguana BurstThe SDE-3 fuses the vintage digital character of the legendary Roland SDE-3000 rackmount delay into a pedalboard-friendly stompbox with a host of modern features.
Released in 1983, the Roland SDE-3000 rackmount delay was a staple for pro players of the era and remains revered for its rich analog/digital hybrid sound and distinctive modulation. BOSS reimagined this retro classic in 2023 with the acclaimed SDE-3000D and SDE-3000EVH, two wide-format pedals with stereo sound, advanced features, and expanded connectivity. The SDE-3 brings the authentic SDE-3000 vibe to a streamlined BOSS compact, enhanced with innovative creative tools for every musical style. The SDE-3 delivers evocative delay sounds that drip with warmth and musicality. The efficient panel provides the primary controls of its vintage benchmark—including delay time, feedback, and independent rate and depth knobs for the modulation—plus additional knobs for expanded sonic potential.
A wide range of tones are available, from basic mono delays and ’80s-style mod/delay combos to moody textures for ambient, chill, and lo-fi music. Along with reproducing the SDE-3000's original mono sound, the SDE-3 includes a powerful Offset knob to create interesting tones with two simultaneous delays. With one simple control, the user can instantly add a second delay to the primary delay. This provides a wealth of mono and stereo colors not available with other delay pedals, including unique doubled sounds and timed dual delays with tap tempo control. The versatile SDE-3 provides output configurations to suit any stage or studio scenario.
Two stereo modes include discrete left/right delays and a panning option for ultra-wide sounds that move across the stereo field. Dry and effect-only signals can be sent to two amps for wet/dry setups, and the direct sound can be muted for studio mixing and parallel effect rigs. The SDE-3 offers numerous control options to enhance live and studio performances. Tap tempo mode is available with a press and hold of the pedal switch, while the TRS MIDI input can be used to sync the delay time with clock signals from DAWs, pedals, and drum machines. Optional external footswitches provide on-demand access to tap tempo and a hold function for on-the-fly looping. Alternately, an expression pedal can be used to control the Level, Feedback, and Time knobs for delay mix adjustment, wild pitch effects, and dramatic self-oscillation.
The new BOSS SDE-3 Dual Delay Pedal will be available for purchase at authorized U.S. BOSS retailers in October for $219.99. To learn more, visit www.boss.info.