Luthier Dave Helmer shows you how to cure buzzy strings, bad intonation, gnarly frets, high action, and other common troubles with off-the-shelf axes.
Guitars are the best. We love them. It’s fun to fall in love with a guitar at a store, buy it, and proudly bring it home. But we’ve all been there … where after a month that new guitar is just not playing as good as it was before. As guitar players, we know what feels good and what feels bad when it comes to playability. Maybe you have setup preferences that you like on all your guitars, or maybe you want to experiment with changes to your setup?
With a few tools, you can perform a handful of tasks that will make your new axe play better and stay in tune. This article is for folks who already know how to tighten loose parts, raise and lower string saddles or bridges, and adjust their truss rods—though I’ll share a tip on how to check it with even more accuracy.
Is that big bulky stock nut uncomfortable on your hand? Let’s trim it down and reshape it. If the action feels high and the neck looks straight, I’ll show you how to lower the action. And haven’t we all swapped out pickups and wondered, “Do they really sound better, or do I think that just because they’re new?” Before you swap your pickups, I’ll share some pickup-height measurements that might make you change your mind.
But wait! There’s more. With everything feeling and playing great, does moving into the upper register start to sound out of tune? Intonation is very easy to check and adjust. When you go to vibrato or hold a note, do the frets feel “sandy”? Are the fret ends rubbing against your hand while you play? Let’s flush and polish those up.
To be clear, we’re not swapping out anything on your new guitar: We’re simply refining the setup. Be sure to go online to see eight videos I made showing various processes covered in this story.
Begin the Beguine
There is an order of operations for best results. Neck relief is the first item to dial in, followed by getting the nut slots cut to the proper depth. After that, setting your string and pickup heights is in order. The final step is setting intonation.
Fret polishing is its own event and can happen anytime between string changes. Getting the frets feeling comfortable and well-polished will take some time and attention. You’ll also need some specialized tools as well as some that can be found in most households. Check the box for my list.
Tools You’ll Need
All of the specialized tools in this list are available through online suppliers, including StewMac and Amazon.
- 6" Ruler with measures in 64ths
- String action gauge [Photo 1]
- Miscellaneous screwdrivers
- Allen wrenches
- Radius blocks
- Understring radius gauges (with the radius on the bottom and the top)
- Fret-end dressing file
- Micro-Mesh sticks [Photo 2]
- Tape (low tack)
- Cotton swabs
- Paper towels (blue shop towels preferred)
- Clean cotton rags
- Nut files [Photo 3]
- Stikit sandpaper
- Tri-Flow lubricant
- Capo
- Feeler gauges
- Simichrome polish
Polishing the Frets
Photo 4
Let’s start with the most Zen of these tasks: fret polishing.
Tape off the fretboard using low-tack tape, exposing only the frets. De-tack each piece of tape on your clothing or maybe a rag—I use my jeans or my sweatshirt. Making it less sticky helps prevent pulling finish off a maple fretboard or the neck. Taping the fretboard also prevents putting any cross-grain scratches into it while you file and polish. You can choose to tape off the entire fretboard or work your way down one fret at a time. Dealer’s choice.
One thing to note about tape, any tape: Even when you de-tack it, you do not want to leave it on overnight. If that happens, rub the tape with your finger, which will break the surface tension. Then carefully pull the tape off from a corner, making sure you’re pulling it off at an angle and not at a straight line with the fretboard edge.
Every fret end has a small burr on the corner from the initial fret job. The fret-end dressing file has a non-marring smooth side for rounding the fret end, and a safe square edge for getting into the corner of the fret end. So, take the fret-end dressing file, use the squared off-side, and file both corners of the fret end [Photo 4].
How to Polish Frets
Here’s how easy it is to polish and smooth frets.
One or two strokes is all you’ll need. Then, using the non-marring side of the file, slightly round off the fret ends.
Photo 5
With the file positioned vertically, file downward to make the fret end flush with the edge of the fretboard.
Photo 6
For a nice, rounded-off look, polish the frets using the same rounding motion from the previous step, working through all three grits of the Micro-Mesh stick.
Photo 7
Then, polish both the sides and the top of the frets.
Photos 8 (top) & 9 (bottom)
Using a soft cloth and Simichrome, buff every fret. This will give you a great shine and help prevent oxidation. Now it’s time to remove the tape and condition the fingerboard if it needs it.
Note: Every fret has two fret ends to clean up and polish along with the fret itself. This is a fair amount of handwork. If you’ve never done it, you will get tired and need a break. Take that break. Take multiple breaks. Let the process take however long it requires without rushing. If you’re new, do all the fret polishing over a weekend or a few days. It should be fun, not painful. If it is difficult, call your local luthier and hire them to do it for you.
Adjusting Neck Relief
Photo 10
Neck relief refers to the slight amount of concave bowing intentionally created in the neck of a guitar or bass by adjusting the truss rod. For the safety of the guitar, be sure to slack the strings before doing any adjustments to the truss rod. Neither you nor your guitar needs to be tense during this process.
Before whipping out an Allen wrench for the truss rod, start by sight-checking the neck’s straightness. You can sight the neck with the guitar on its back, but I like to put it on edge and look at it that way. It’s easier to see how much curve there is when the guitar is on its side. I feel like gravity plays tricks on my eyes when I sight the neck with the guitar on its back. When I play the guitar, it’s on its side anyway, so looking at it from this vantage point is best.
Tune the guitar to pitch, put a capo on the first fret, and press fret 15 with your left hand.
Photo 11
With your right hand, take a feeler gauge and check the gap at frets 7 through 9 (left-handed players, flip your hands around) [Photo 11].
From the top of the fret to the bottom of the string, the gap is usually anywhere from .003" to .012", depending on the feel you are going for. The feeler gauge should fit just between the top of the fret and the bottom of the string. The string shouldn’t move. This will tell you how much “relief” is in the neck. If you find this challenging, keep going—this will take some practice.
When dialing in the relief, I go back and forth between adjusting the truss rod and the string action. Getting the strings low and playing clean on a budget axe can be a challenge. Usually the fretwork isn’t that great, and in the upper register the frets can be unlevel, causing buzzes and clanks. If you need to raise the string action to get the notes to play clean, some fret leveling may be in order. (For more on fret leveling, go online to our article “About Fret Leveling,” from the December 2007 issue.) For good energy transfer, the neck should be as straight as possible. If the neck is straight and the frets are not level, the strings will buzz with low action.
In general, the flatter the radius on the fretboard, the straighter you can get the neck with the truss rod adjustment. On a fretboard with a 12" radius, you should be able to get .005" relief, and on a vintage 7.25" radius board you may need as much as .014" relief. The only way to get better at checking and setting relief is practice.
Refining the Nut
String buzzes, pinging noises when you tune, strings sticking in the slots, and too much string motion in the nut slots are all indicators of trouble. Before getting out the sandpaper and Micro-Mesh sticks, be sure you know if your guitar’s nut is TUSQ or bone. TUSQ is softer, so you should leave TUSQ nut slots a little higher. This leaves room for the TUSQ to wear without causing buzzing on the first fret. With bone, you can cut the slots lower, because it holds up to string wear.
How to Shape Your Guitar's Nut
Watch as Dave Helmer sands down the back half of a nut and creates a smooth finish.
The back side of the nut is usually very bulky and could often stand to lose some material to be more comfortable on your hand. So, let’s start there. Tape off the neck and headstock around the nut using a few layers of tape to protect the headstock face and fretboard. Then, slack the strings and pull them to either side of the nut.
Sand a bevel into the backside—the side closest to the headstock—of the nut using P320 and P400 grit Stikit sandpaper on a flat sanding stick.
Photo 12
The bevel should start at the back of the nut and come forward about one-third to one-half the thickness of the nut [Photo 12]. Use P320 for most of the sanding and switch to P400 for the last 5 to 10 strokes.
Next, take a fresh Micro-Mesh stick and work through the various grits to buff/round over the bevel you’ve sanded into back of the nut, so it looks and feels good.
Photo 13
TUSQ nuts are often tall, and the strings sit deep in the slots.
Photos 14 (left) & 15 (right)
Wound strings require 50 percent of the diameter of the string to sit in the nut slot, with the other 50 percent above the top of the nut surface. The plain strings should be flush with the top of the nut. Take a look at the wrong appearance [Photo 14] and the correct look [Photo 15] for properly seated strings.
How to Sand Your Guitar's Nut
Our luthier shows you how to use a radius block and sand down a nut.
Use a radius block that matches the radius of your fretboard.
Photo 16
With P320 and P400 grit Stikit sandpapers, use mild pressure to sand down the top of the nut. Sand a bit and check your progress by setting the strings in the slots and putting a little tension on them. Tuning to pitch isn’t necessary. Use the P320 for most of the sanding, and switch to P400 when you are close to the 50/50 height for the wound strings. The radius block sanding will leave a flat, sharp edge on each side of the TUSQ nut [Photo 16]. To round over the sharp edge, use the sanding block and Micro-Mesh stick.
Use the coarse grit of a Micro-Mesh stick to round over and blend the bevel from the back into the top of the nut. Work through the grit gauges until it’s smooth. There is a fine balance between the bevel at the back of the nut and the top radius of the nut. Go back and forth between the two steps to get a nice, finished look and a nut that functions at optimal levels.
… And Refining the Nut Slots
Photo 17
Nut height is the distance from the top of the first fret to the bottom of the string. A good height on the wound strings is about .020", and for the plain strings about .015". Measuring this gap with a feeler gauge can be tricky because of the fretboard radius. Many repair folks do this by eye and feel, based on experience. It takes some practice. A good check: At pitch, fret the third fret and check for a small gap between the string and the top of the first fret.
How to Widen Your Guitar's Nut Slots
A diamond file can make quick work of deepening and widening nut slots.
The bottom of the string should be sitting on the bottom of the front half of the nut slot [Photo 17]. File down each nut slot to its proper depth using the corresponding nut file. There are diamond nut files on the market in multiple sizes to accommodate many string gauges. Make sure to keep your strokes straight. The standard-toothed files have less sizes and usually require rolling them from side to side to get a well-fit string.
Next, using a proper-sized file, round over the bottom back half of the nut slots down, toward the face of the headstock and away from the strings. This will allow the strings to move freely during tuning or bending, while still having support from the front half of the slot.
How to File D and G String Slots on Guitar
Photo 18
On guitars with 3x3 headstock configurations, the D and G strings need the back half of the slots feathered out away from the center, so the string has a direct path to the tuner post. Using a file that is one size bigger than the string and rolling it side to side on the back of the nut slot will give the string a straight path to the tuner post. Photo 18 is my illustration showing which slots need feathering.
Watch How to File D and G String Slots on Guitar
The D and G nut slots require special attention on 3x3-style headstock configurations.
Additionally, use pencil lead to lubricate the slots. Just get in there with the point of a pencil and mark the slot with its graphite. You might also put a drop of Tri-Flow on the front of the string tree. Tri-Flow will run down the string, so take a cotton swab or cloth to clean up any excess. Tri-Flow has Teflon in it, so you don’t need much.
Adjusting String Action
Photo 19
First, find your string height by measuring the string action at the 17th fret on a Fender-style guitar and at the 15th fret on a Gibson-style instrument.On electric guitars, action can range from 3/64" to 3/32", depending on the player’s comfort. My preferences are 1/16" on the treble side and 5/64"on the bass side on both Fender- and Gibson-style guitars measured at the appropriate fret.
How to Adjust Guitar Action
Here’s a look at how our author adjusts the action.
Always loosen the string tension before making action adjustments. This will save wear and tear on the small bridge components. Take either a 6" ruler or a string action gauge and set it on the frets. Measure from the top of the fret to the bottom of the string [Photo 19].
If the action is high, you will lower that string’s saddle or that side of the bridge. If it is low, you will raise it. Make sure the individual saddles are sitting square and upright to the face of the bridge. You do not want them sitting at an angle or leaning over. This will cause buzzing.
The bottom of the strings should match the radius of the fretboard when measured with an understring radius gauge.
Photo 20
Start your adjustment with the outside strings, working toward the center. On Fender-style guitars, set the two outside strings to the height you want and have the middle four strings a bit higher than that. Bring the gauge up from underneath and just touch the two outside strings. Then, bring the strings down a little at a time until the radius matches.
On a Gibson-style Tune-o-matic, the saddles are not individually adjustable. So, if the radius doesn’t match, the saddles will need to be filed. To do this, I recommend using toothed nut files and a rolling side-to-side motion. Do a little work and check your progress. Remember to slack your strings when adjusting the saddle or bridge up or down.
Changing Pickup Height
Photo 21
Finally, let’s take a look at pickup-height adjustment. First, to check pickup height, use the two outside strings again. Press the top wound string on the last fret and measure the distance from the top of the pole piece to the bottom of the string [Photo 21]. This distance can range from 3/64" to 1/8". My preferences are 1/16" on the treble side and 5/64" on the bass side.
Adjusting Guitar Pickup Height
Dave Helmer walks you through the process of adjusting the height of your guitar’s pickups.
On most styles of pickups, there are height adjustment screws on either side of the pickup to raise or lower it. The closer the pickup gets to the strings, the more present string frequencies become. If you get too close, the magnetic pull can affect the string’s vibration and you may hear some strange sounds as you go into the upper register.
On Strats, the neck pickup is regularly set too close, and at the 12th fret and above, the low E and A can sound choked, honky, and not clear. Lowering the neck pickup with a screwdriver usually solves this issue.
Setting Intonation
Photo 22
If you can’t get your guitar accurately in tune, you might need to check its intonation. Adjust all saddles as far back as possible so every string will play flat at the 12th fret. You will adjust the saddles forward, gradually making the octave play sharper until it’s in tune with the open string [Photo 22].
Adjust Your Guitar's Intonation
With a tuner and a screwdriver, Dave Helmer shows you how to adjust your guitar’s intonation.
Depending on your vibrato style, experiment with intonating the plain strings slightly flat. Use your ear and do what sounds good. Sometimes, the plain strings can have perfect intonation, but playing with vibrato can make them sound sharp.
To fine-tune intonation, the individual bridge saddles must be adjustable. Once the intonation is set, recheck the string radius using the understring radius gauge and adjust as needed. The radius can change as the saddles come forward during intonation.
Tri-Flow is great for lubricating saddle parts. Put a small drop on the saddle-height adjustment screws and capillary action will suck it in. Adjust the saddle up and down a few times to coat the threads. Clean up any excess with a cotton swab or cloth. Put a drop or two onto a cotton swab and apply the Tri-Flow to the top of each saddle where the string rests. This will help strings move freely during tuning and after any bends or vibrato.
And that’s it! For a relatively small investment in tools and time, you’re now ready to supercharge your new guitar—and maybe your long-treasured axes, too.
- DIY: How to Set Up a Fender Stratocaster - Premier Guitar ›
- 12-String Setup Secrets - Premier Guitar ›
- DIY: How to Set Up and Intonate an Acoustic Guitar - Premier Guitar ›
- Reader Guitar of the Month—Pickups and Finishes - Premier Guitar ›
- DIY Guitar: 7 Cool Reader Mods - Premier Guitar ›
With authentic stage-class Katana amp sounds, wireless music streaming, and advanced spatial technology, the KATANA:GO is designed to offer a premium sound experience without the need for amps or pedals.
BOSS announces the return of KATANA:GO, an ultra-compact headphone amplifier for daily jams with a guitar or bass. KATANA:GO puts authentic sounds from the stage-class BOSS Katana amp series at the instrument’s output jack, paired with wireless music streaming, sound editing, and learning tools on the user’s smartphone. Advanced spatial technology provides a rich 3D audio experience, while BOSS Tone Exchange offers an infinite sound library to explore any musical style.
Offering all the features of the previous generation in a refreshed external design, KATANA:GO delivers premium sound for everyday playing without the hassle of amps, pedals, and computer interfaces. Users can simply plug it into their instrument, connect earbuds or headphones, call up a memory, and go. Onboard controls provide access to volume, memory selection, and other essential functions, while the built-in screen displays the tuner and current memory. The rechargeable battery offers up to five hours of continuous playing time, and the integrated 1/4-inch plug folds down to create a pocket-size package that’s ready to travel anywhere.
KATANA:GO drives sessions with genuine sounds from the best-selling Katana stage amp series. Guitar mode features 10 unique amp characters, including clean, crunch, the high-gain BOSS Brown type, two acoustic/electric guitar characters, and more. There’s also a dedicated bass mode with Vintage, Modern, and Flat types directly ported from the Katana Bass amplifiers. Each mode includes a massive library of BOSS effects to explore, with deep sound customization available in the companion BOSS Tone Studio app for iOS and Android.
The innovative Stage Feel feature in KATANA:GO provides an immersive audio experience with advanced BOSS spatial technology. Presets allow the user to position the amp sound and backing music in different places in the sound field, giving the impression of playing with a backline on stage or jamming in a room with friends.
The guitar and bass modes in KATANA:GO each feature 30 memories loaded with ready-to-play sounds. BOSS Tone Studio allows the player to tweak preset memories, create sounds from scratch, or import Tone Setting memories created with stage-class Katana guitar and bass amplifiers. The app also provides integrated access to BOSS Tone Exchange, where users can download professionally curated Livesets and share sounds with the global BOSS community.
Pairing KATANA:GO with a smartphone offers a complete mobile solution to supercharge daily practice. Players can jam along with songs from their music library and tap into BOSS Tone Studio’s Session feature to hone skills with YouTube learning content. It’s possible to build song lists, loop sections for focused study, and set timestamps to have KATANA:GO switch memories automatically while playing with YouTube backing tracks.
The versatile KATANA:GO functions as a USB audio interface for music production and online content creation on a computer or mobile device. External control of wah, volume, memory selection, and more are also supported via the optional EV-1-WL Wireless MIDI Expression Pedal and FS-1-WL Wireless Footswitch.
For more information, please visit boss.info.
Featuring torrefied solid Sitka Spruce tops, mahogany neck, back, and sides, and Fishman Presys VT EQ System, these guitars are designed to deliver quality tone and playability at an affordable price point.
Cort Guitars, acclaimed for creating instruments that exceed in value and quality, introduces the Essence Series. This stunning set of acoustic guitars is designed for musicians looking for the quintessential classic acoustic guitar with fabulous tone all at an exceptional price point. The Essence Series features two distinct body shapes: The Grand Auditorium and the OM Cutaway. Whatever the flavor, the Essence Series has the style to suit.
The Essence-GA-4 is the perfect Grand Auditorium acoustic. Wider than a dreadnought, the Essence-GA-4 features a deep body with a narrower waist and a width of 1 ¾” (45mm) at the nut. The result is an instrument that is ideal for any number of playing styles: Picking… strumming… the Essence GA-4 is completely up for the task.
The Essence-OM-4 features a shallower body creating a closer connection to the player allowing for ease of use on stage. With its 1 11/16’th (43mm) nut width, this Orchestra Model is great for fingerpickers or singer/guitarists looking for better body contact for an overall better playing experience.
Both acoustics are topped with a torrefied solid Sitka Spruce top using Cort’s ATV process. The ATV process or “Aged to Vintage”, “ages” the Spruce top to give it the big and open tone of older, highly-sought-after acoustics. To further enhance those vintage tones, the tops bracing is also made of torrefied spruce. The mahogany neck, back, and sides create a warm, robust midrange and bright highs. A rosewood fingerboard and bridge add for a more balanced sound and sustain. The result is amazing tone at first strum. 18:1 Vintage Open Gear Tuners on the mahogany headstock offer precise tuning with vintage styling. The herringbone rosette & purfling accentuates the aesthetics of these instruments adding to their appeal. Both acoustics come in two choices of finish. Natural Semi-Gloss allows the Sitka spruce’s natural beauty to shine through and classic Black Top Semi-Gloss.
A Fishman® Presys VT EQ System is installed inside the body versus other systems that cut into the body to be installed. This means the instrument keeps its natural resonance and acoustic flair. The Presys VT EQ System keeps it simple with only Volume and Tone controls resulting in a true, crisp acoustic sound. Lastly, Elixir® Nanoweb Phosphor Bronze Light .012-.053 Acoustic Strings round out these acoustics. This Number 1 acoustic guitar string delivers consistent performance and extended tone life with phosphor bronze sparkle and warmth. The Essence Series takes all these elements, combines them, and exceeds in playability, looks, and affordability.
Street Price: $449.00
For more information, please visit cortguitars.com.
Cort Essence-GA4 Demo - YouTube
Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.Moth Electric's C. regalis overdrive pedal offers massive boost, natural overdrive, and searing distortion for guitar and bass. With active treble and bass controls, clean blend, Smooth/Crunch modes, and true-bypass switching, this USA-made pedal is a versatile addition to any pedalboard.
Adding a new model to their line of overdrives, Moth Electric has released the C. regalis. Equally suited for guitar and bass, the meticulously designed C.regalis is capable of massive boost, natural, singing overdrive, and searing mid-gain distortion. Its six op-amps power a dynamic, crunchy overdrive circuit with a suite of features including:
- Active treble and bass controls that allow for +/- 15db boost and cut. Perfect for tailoring the C. regalis to your instrument and amp.
- A powerful clean blend for introducing either your amp’s natural character or another effect into the equation. Allows the C. regalis to become a more transparent overdrive.
- Smooth/Crunch modes, provide a subtle change in feel with ‘Smooth’ increasing sustain and ‘Crunch’ introducing high-order harmonics for additional texture.
The C. regalis offers the following features:
- Bass, Treble, Blend, Volume, Drive controls
- Smooth/Crunch modes● More volume than you’ll ever need
- True-bypass switching, top-mounted jacks for easy placement on crowded pedalboards
- 9-volt DC operation with external power supply – no battery compartment
- Designed and hand-built in the USA using through-hole components
The C. regalis carries a $179.99 price and is available for purchase at mothelectric.com.
For more information, please visit mothelectric.com.
OK WOW. Moth Electric C.REGALIS - Pedals and Tea EP 57 - YouTube
Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.The long-running noise rockers detail what they packed for their January 2025 run across the U.K.
When the Jesus Lizard released their seventh studio record, Rack, last September, it ended a 26-year hiatus between recordings, and lovers of raucous, steely rock music around the world rejoiced. As guitarist Duane Denison told PG’s Nick Millevoi in our feature story, the key to the album’s vitality—and reviving the band’s brutal sound—was simple: “Practice loud.”
Ahead of a hotly anticipated U.K. tour celebrating the record, the band gathered at SIR’s rehearsal space in Nashville to do exactly that. PG’s Chris Kies stopped by to see what Denison and bassist David Wm. Sims were stuffing into their suitcases for the trip across the pond.
Brought to you by D’Addario.Higher Powers
The last time Denison invited us to his Nashville home for a Rig Rundown, he was using Electrical Guitar Company models. This time around, he’s smitten with this Powers Electric Type A. Most of the guitar’s features are proprietary, including the bridge, pickups, and the vibrato system. The trussed hollowbody is made from urban ash with a solid maple top, and comes with a compound radius Honduran rosewood fretboard.
Denison digs the definition and articulation in the attack of the discrete FF42 single-coil pickups, which bridge the gap between a humbucker’s hot output and a traditional single-coil’s brightness. He goes through four different tunings in the current Lizard set: E standard, drop D (for “Hide & Seek”), drop G (on “Thumbscrews”), and a strange tuning with flat E and D strings for “Thumper.” Coated Stringjoy Orbiters (.105–0.50) handle the changes, as well as the Stringjoy Jumbo Jazz picks Denison uses.
Sweet Victory
Denison has switched from Blackstar amps to this 2-channel Victory VS100 Super Sheriff. He’s always preferred British amps: “American guitars and English amps make the world go round,” he says. Denison also uses a Marshall JCM900, which he appreciates for its simplicity compared to the JVM series, and its versatility compared to the JCM800.
Helix Help
Denison sets up this Line 6 Helix as a pedalboard, with tweaked versions of his favorite analog delay pedals programmed in. Among his go-to effects are reverb, slapback delay, tremolo, chorus, wah, longer delay, and what he calls a “wildcare effect,” which comes into play for “What If?”
The Best $250 Ever Spent
Sims bought this Memphis brand Jazz-style bass in 1981 for $250, and it’s still his No. 1. He strings it with Rotosound RS66LDs, which he needs to change every three or four shows; once he senses the attack softening, he slaps new ones on.
Boomtown Brightness
Sims blasts his bass through this Gallien-Krueger 800RB, set for a classic midrange scoop with plenty of bite and bottom end. He prefers Ampeg 8x10 cabinets, or 2x15 speaker cabs.
Triple Combo
No fancy floor unit for Sims. He’s got a Boss ODB-3, an MXR Bass Chorus Deluxe, and an MXR Phase 90, all of which are used sparingly throughout the set.