
When it comes to cosmic tone, itās critical to have functional potentiometers. Hereās how to install them correctly and keep them ship-shape afterward.
(Originally published March 27, 2020)
Over the last few years, we've discussed the construction of potentiometers and diagnosed several potential problems with these essential, yet sometimes pesky, electric guitar components. (If you missed these, check out āThe Trouble with Tribbles" and āDealing with Knobs and Pots.")
Let's now consider problems that can occur when replacing pots, and then discuss ways to either avoid or solve these potential issues. Over the years I've analyzed virtual cries for help from hundreds of customers, and as a result I can safely say that non-working pots fall into one of two categories that account for essentially 100 percent of the problems: (1) mechanical damage while installing the pots, or (2) soldering damage when wiring them up. It's very, very rare that a pot comes DOA from the factory. Reputable manufactures have quality control systems to prevent this, so it's almost guaranteed that a problem with a potentiometer has to do with the end user. So let's take a look at these two scenarios.
Mechanical damage.
In this case, the most common damage is caused by overtightening the nuts, especially when installing pots into a guitar with a stiff wooden top like a Les Paul.When installing pots, forget the adage "the more, the merrier." Instead, keep this in mind: The next level beyond "tight" and "super-tight" is "broken." Guitar pots don't have to handle a lot of weight or withstand a nuclear strike, so they should only be screwed down tight enough to remain immobile when you rotate the knobs.
First and foremost, it's essential that you install the pots correctly. This might sound obvious or trivial, but you can't imagine how many guitars I've seen where pots have been installed in, shall we say, unusually creative ways.
Here's how to do it right: The first step is to slip the lock washer onto the pot shaft and then insert the shaft through the hole in your guitar's pickguard or top. With the shaft protruding through the other side, now put the flash washer on the shaft, followed by the hex nut, which you can initially thread with your fingers. Finally, use a socket wrench, small adjustable wrench, or an ESP Multi Spanner to carefully tighten the hex nut until it's snug against the washer and doesn't turn anymore.
If you discover that the pot sits too high on your pickguard or guitar top, you'll need to remove the pot and start over by first threading another hex nut on the shaft, followed by the lock washer, and then repeating the installation process. This "underside" hex nut will let you adjust the height of the pot to your individual wishes. Simply insert the shaft through the pickguard or top, eyeball the height, and adjust the hidden hex nut up or down on the pot threads as needed. Finally, add the flash washer and exterior hex nut to complete the process. The key here is to always remember the correct order of these parts.
So what happens to a pot when you overtighten it? If the four tiny tabs that hold the little metal plate to the shaft, wiper, etc., are unable to withstand the force applied to the shaft when you torque down the hex nut, they'll bend and let the plate and the shaft rotate freely. Hmm, no good.
But don't worry, it's an easy fix: Use needle-nose pliers or a small flathead screwdriver to gently pull the tabs up a little more so you can rotate the plate and return it to its centered position. Then bend the tabs back into place so they hold the shaft securely (Photo 1). Done!
It's almost guaranteed that a problem with a potentiometer has to do with the end user.
Other mechanical damage is typically caused by trying to remove or install knobs that aren't made for a given pot's shaft. When you try to hammer down a non-fitting knob, you can easily break the shaft by forcing it through the knob bushing. (In most cases, this happens when trying to force a metric knob, measured in millimeters, onto a U.S. pot shaft, measured in fractions of an inch.)
If you try to remove a jammed knob that someone managed to "fit" using brute forceāor even attach with superglueāchances are good you'll break the wiper inside the pot and pull out the entire shaft along with the knob.
Yet this is easy to avoid: Never try to force a knob onto the pot shaft; instead use one that fits. If you need to remove an improperly fitted knob, use a heat gun to soften the plastic or a saw to split it open. Don't use any upward or downward pressureāthat will ruin the pot, for sure.
Soldering damage.
The easiest way to damage a pot is to overheat it, especially when attaching a ground wire to the back casing. It's a common mistake. When it comes to how long your soldering iron should be in contact with the pot, the golden rule is "as short as possible, but as long as necessary." It takes time to develop this skill, so you'll need to practice. Also, to avoid disaster it's crucial to have the right tools. Here are some helpful guidelines for soldering onto pots.
1. If you don't have a soldering station with an adjustable temperature control, you need at least two different handheld soldering irons: one rated at around 30 watts and the other around 60 watts. This is exactly what I use for any soldering job outside the shop. The 30-watt iron is for soldering on the pot terminals, pickup selector switch terminals, output jack terminalsāthose common tasks. The 30-watt iron is our daily go-to tool for all things guitar at the shop.
The 60-watt iron is for soldering to pot casings and Stratocaster tremolo claws. Don't try to solder to a pot's case with a 30-watt ironāthe solder will need a very long time to flow and you'll expose the pot to a lot of heat. With a 60-watt iron, the solder will flow instantly and soldering time will be very short. This yields strong solder joints.
2. If you want to be on the safe side, remove the case from the pot before you solder to it. That's what I do when I want to avoid damaging vintage pots. To remove the case, gently bend the four metal tabs away from you. To reinstall the case, simply bend the tabs back into place. Take your time and go easy.
3. Always rub the metal casing with 180-grit sandpaper before soldering to it. Manufacturers use all kinds of greasy coatings to protect the case against oxidation, which can make a soldering job close to impossible. So sand the case until it's clean and shiny, and then clean it with naphtha. This will provide the perfect base for a good soldering joint. But don't do this to vintage pots! For those, it's paramount to preserve the patina that comes with age.
4. If you decide not to remove the pot's case, strive to avoid any unnecessary heat. Here are some helpful tips:
- Always turn the pot down to 0 before soldering to its case.
- Use a heat sink on the case. For this job, you'll need something bigger than just a standard clip. To enhance its effect, you can chill the heat sink in the fridge ahead of time.
- If you need to connect one of the terminals to ground, as on most volume pots, don't try to solder the terminal directly to the case by bending it back. This may look cool and vintage, but you'll need a lot of heat and good soldering technique to pull this off. Simply use a piece of solid-core wire and solder it to the terminal and from there to the caseāthis yields the same performance.
- After tinning the case, let it completely cool down before you solder the wire to it.
5. Don't apply excessive solder to a terminalāit will flow down the terminal's leg and find its way inside the pot.
Photo 2 ā Photo courtesy singlecoil.com
Photo 2 shows a pot from my "Hall of Shame" collection. Look at the two red marks at the end of the two terminals. These solder blobs are what happen when you apply way too much solder. There's also a big solder blob on the middle terminal's inner ring. How someone managed to get the solder inside there will forever remain a mystery. On the upper left, notice how the carbon is melted and buckled from too much heat. This poor little thing had to endure cruel treatment ... may it rest in peace!
Remember, if you don't solder regularly, there's no shame in having a professional guitar tech do the work for youāespecially when you have a vintage guitar and need to work on its original pots. Retaining your guitar's value is an excellent investment. Soldering on pots isn't rocket science, but it requires the right tools, experience, and a steady hand.
Maintaining pots.
These are mechanical devices with a limited lifespan, and it's inevitable they'll start to wear out over time. Yes, it's possible to clean, repair, and renew the carbon inside, but this only makes sense for a vintage pot, not a modern one. Instead of trying to repair the latter, it's more cost-effective to simply replace it.
Typical pots are not completely sealed; they have open areas around the terminals, so moisture and dust can creep inside. To prevent this, you can buy pots that are completely sealed or cover standard pots with an additional dust seal. Usually a guitar's electronic compartment is closed and not directly exposed to contamination, so an additional dust cover isn't necessary for our applications.
Also, there's no need to maintain your pots. At a certain point, they'll begin to wear out and make scratchy noises when you turn them. This means it's replacement time! You can delay this a bit with contact cleaner, but this treatment is only temporary. Contact cleaner is cool for some applications, such as servicing hi-fi equipment, but it can't repair worn-out pots.
My advice? Never use contact cleaner on your pots because the cleaner will attract debris, and when it evaporates you're left with hard, dry crudāsomething you definitely do not want inside your pot. To combat this, you'll spray more cleaner and thus begin a destructive cycle. This results in replacing the pot much earlier than necessary, exactly the opposite of what you want. We all know the road to hell is paved with good intentions. If a pot is really dusty and making scratchy noisesāmaybe you took your Tele to Burning Manāthe best thing to do is open it up and swab everything with Q-Tips soaked in naphtha.
Finally, when it comes time to replace a pot, pay attention to the specs. Some pots are designed for 2,000 rotations while others are tested to withstand 20,000. You get what you pay for, and this isn't a place to cut corners.
All right! Next month we'll examine the Peavey Omniac JD, Jerry Donahue's signature model T-style, and I'll show you how to transfer its sophisticated wiring scheme to your own guitar. Until then ... keep on modding!
- Three Must-Try Guitar Wiring Mods - Premier Guitar āŗ
- Mod Garage: Three Ways to Wire a Tone Pot - Premier Guitar āŗ
- Mod Garage: Dealing with Knobs and Pots - Premier Guitar āŗ
From full-size to mini, these six pedals deliver funky āchickas,ā screaming, fuzz-infused lead tones, and more.
The variations on a classic stompbox bring you tonal versatility and more!
Xotic XW-2 Wah Pedal
The Xotic XW-2 Wah Pedal is a high-quality, versatile stomp that creates a ā70s-style āthroatyā wah sound.
xotic.us
Sonicake FlipWah
The FlipWah combo pedal combines a classic wah and active volume pedal in one, with a footswitch to select between the two modes. A Q knob adds even more versatility.
sonicake.com
$79 street
McCon-O-WahĀ McWah
The McWah-2B delivers classic tone with modern upgrades. Handwired, adjustable, and durable, it features a custom pot and true bypass for optimal sound. Inspired by the original, legendary wah pedal.
mcconowah.com
$428 street
Dunlop Jerry Cantrell Rainier Fog Cry Baby Wah
This Cry Baby signature model complements Jerry Cantrellās sound with a dark, punchy voice, a wide sweep, and a control on the side for fine-tuning the toe-down frequency.
jimdunlop.com
Dunlop CBJ95 Cry Baby Junior Wah Pedal
The Cry Baby Junior Wah features front-mounted jacks and an 8" housing for clean configurations on the worldās most popular boards.
jimdunlop.com
Dunlop Cry Baby Daredevil Fuzz Wah Pedal
A collaboration with Daredevil Pedals, this Cry Baby Wah combines the bright, aggressive vocality of a modded Cry Baby Wah with a custom fuzz circuit thatās downright gnarly.
jimdunlop.com
Leveraging 3D printing technology, the new Floyd Rose Original locking nuts are designed to deliver unmatched precision and consistency, replacing the traditional ālost waxā casting method that dominated for decades.
The shift to 3D printing allows for intricate detailing and tighter tolerances, ensuring each nut meets exact specifications.
The process begins with powdered metal, which is precisely 3D printed into the desired shape using advanced metal printing technology. After printing, the parts are depowdered and cleaned before undergoing a sintering processāan advanced heat treatmentāduring which the parts achieve full density and hardness. Lastly, the nuts are CNC ākiss-cutā to exacting specifications for consistency and control of the fit before receiving a premium electroplating finish.
āFloyd Rose has always been synonymous with innovation, and by embracing this incredible new technology we are able to continue that legacy,ā said Andrew Papiccio, president of AP International Music Supply of which Floyd Rose is a division. āThe accuracy and flexibility of the new 3D printing method will allow us to make a more consistent piece while also giving us full control of the manufacturing right here in the USA.ā
Initially, the 3D-printed locking nuts will be available in ten classic sizes with a 10ā radius, with plans to expand the range to accommodate various fretboard radii in Spring 2025. This augmentation will offer players more options for customizing their setups to match a wide variety of fretboard curvatures.
To get a sneak peek at the new Floyd Rose USA Series, come visit us at NAMM in booth 5734 in Hall D.
With flexible voltage adjustments, precise control, customizable protection, compact design, and affordable pricing at $299, the Brownie is the ultimate solution for optimizing tone and safeguarding your gear.
AmpRx, the trusted name behind the industry-renowned BrownBox, has unveiled its newest innovation: The Brownie, a voltage-optimizing power supply for modern amps and the first of its kind.
Designed by AmpRx co-owner and CEO Cassandra Sotos (2024 NAMM Female Entrepreneur of the Year), the Brownie provides unparalleled control, flexibility, and protection specifically for modern tube amplifiers by allowing the player to both increase and decrease voltage with volt-by-volt precision.
Priced at $299, the Brownie offers an affordable and essential solution for protecting your investment in your high-quality tube amp. It allows you to optimize your tone and safeguard your gear from variations in voltage by givingthe ultimate advantage: knowing exactly what youāre feeding your amp.
Known as the secret weapon of touring professionals, AmpRx products have been spotted on stage with bands like the Red Hot Chili Peppers, Lynyrd Skynyrd, Zac Brown Band, Iron Maiden, and many more. AmpRx is now bringing its game-changing technology to an even broader audience with this compact, affordable, and versatile product. Try the Brownie for yourself and discover exactly why artists, amp designers, and technicians rely on AmpRx to provide consistent sound, performance, and extend the life of their gear.
The Brownie will be available January 20th, 2025, presented at NAMM Global Media Day and on display at Booth #5630.
WHAT MAKES THE BROWNIE SPECIAL? Building on the success of the flagship BrownBox, the Brownie offers key innovations tailored for modern amplifiers:
- Flexible Voltage Adjustments: The Brownie is the first in the AmpRx line to both decrease and increase voltage, providing optimal performance for modern tube amps (often at 117-120V).
- Precise Control: Adjust voltage in ultra-precise -1V increments when decreasing, and by +3V or +5Vwhen increasing, allowing musicians to fine-tune their tone with precision.
- Customizable Protection: The Brownie ensures safe operation, putting control directly in the player's hands, and includes two fuse options: 2A for smaller setups and 4A for larger setups, ensuring compatibility with diverse gear.
- Compact and Portable Design: Smaller and lighter than the original BrownBox, the Brownie is perfect for musicians seeking portability, durability, and streamlined functionality. It can even fit on a pedalboard or in a backpack.
- Wide Accessibility: At just $299, the Brownie offers professional-grade voltage control at a price point thatās accessible to musicians everywhere.
Email sales@brownbox.rocks to order and stop by NAMM Booth #5630 to see the Brownie in action, talk with the owners, team and artists, and see exactly why so many people insist onAmpRx products when they make music.
For more information, please visit brownbox.rocks.