
Photo 1 shows the 4PDT switching matrix design for the "up" position, which will put the pickups half out-of-phase.
We've discussed full out-of-phase and half out-of-phase pickup switching. Here's a wiring for those who want it all in one switch.
Hello and welcome back to Mod Garage. After exploring the half out-of-phase pickup option several times in the past, there was a lot of interest, and I received a lot of emails from readers about it. A lot of you asked for a multi-phase switch to have all possible options at the ready and today we'll bring it all together. You asked for it, and the Mod Garage delivers!
Let's start with what we'll need to get out-of-phase or half out-of-phase sounds:
- You will need to engage at least two pickups to get such sounds. A single pickup played by itself will always sound the same, no matter if you play it in phase or out of phase (more about this later). The magic starts when you engage two (or more) pickups with one in phase and the other one out of phase or half out of phase.
- In general, you'll need one switch for each pickup you want to put out of phase. This can be only one switch, like on the middle pickup of a Stratocaster, to cover both in-between switching positions (bridge+middle and neck+middle), or three phasing switches, like on Brian May´s "Red Special," with one switch for each of the three pickups.
My design of a multi-phase switch that we'll cover today can be used to expand already existing out-of-phase switches in a guitar or to design a new wiring of your choice, integrating such a switch. With this switch, you'll be able to cover all three possible phasing options: in phase, out of phase, and half out of phase.
The magic starts when you engage two (or more) pickups with one in phase and the other one out of phase or half out of phase.
All you need for this mod is the switch, plus a capacitor and a resistor for the half out-of-phase option. So, let's start with the switch itself. For this mod you need a 4PDT on-on-on switch, which means a switch with three switching positions (up-middle-down) and a total of 12 lugs, arranged in four independent sections. Such switches are on the border of being exotic, but they're still available. Since every manufacturer uses a slightly different switching matrix for such switches, you'll need to get one with the same switching matrix I used, which is more or less the quasi-standard for it. It's possible to use 4PDT switches with a different switching matrix, but you'd have to adopt the wiring to it. I've provided three photos of the switching matrix and the switch design for each position. Photo 1 shows the "up" position, which will put the pickups half out-of-phase. Photo 2 shows the "middle" position, which will give you the full out-of-phase option. And Photo 3 shows the "down" position, which is just the normal in-phase operation.
Placing such physically large-sized switches on a pickguard or control plate can be a challenge, so you'll have to be creative. There is no way around such a switch when you want this mod because there are no existing push-pull or push-push pots with on-on-on switches. If you can find a 4P3T rotary switch, you can use it to substitute the switch by replacing one of the pots with it. There are also 4PDT slider switches available, but they're physically about the same size, and therefore, not a real alternative.
Photo 2 shows the 4PDT switching matrix design for the "middle" position, which will give you the full out-of-phase option.
Image courtesy of singlecoil.com
Here we go with the wiring of the switch, shown in Fig. 1. With the lever down you have the normal in-phase operation, with the lever up the pickup is half-out-of-phase, and in the middle position you have the full out-of-phase option.
Anyway, there you have it, all in one switch as shown in Fig. 1. On the left side of the switch, you see a capacitor in series with a resistor for the half out-of-phase option. A good average value is using a 0.01 uF capacitor with a 6.2k-ohm resistor in series as an additional serial attenuation of the system, preventing an impedance peak.
When looking at the switch, you'll notice that one switching stage is not populated at all. You might ask: Why don't we use a 3PDT switch for this if we only need three switching stages? This is because of the asymmetrical switching matrix of the 4PDT switches in the middle position (Photo 2) and there's no way around it. If the on-on-on switch had a completely symmetrical switching matrix, then three switching stages would be enough, but such switches aren't available today.
Photo 3 shows the 4PDT switching matrix design "down" position, which is just a normal in-phase option.
Image courtesy of singlecoil.com
In general, you add a controlled degree of reversed phase of the pickup when using the half out-of-phase option, which is great to mimic Stratocaster in-between "quack tones" on a Telecaster, like on the Jerry Donahue Tele models or with the Bill Lawrence Telecaster wiring.
Phase differences are measured in degrees. Totally in-phase sounds have either 0 or 360 degrees of difference, meaning none. Totally out-of-phase sounds have a 180-degree difference. So, half out of phase is either 90 or 270 degrees of difference. That's the reason why you can only achieve a fully out-of-phase effect when using two pickups together with one wired out-of-phase. (When both pickups are wired out of phase, they sound the same as both pickups in phase, because there are still 0 degrees of phase difference between them.) When a signal passes through a capacitor, the voltage leads the current by 90 degrees, so when a pickup's signal gets routed through a capacitor, it shifts the phase by 90 degrees—exactly half of 180 degrees—and therefore half out-of-phase ... in simple terms.
The cap connected to the switch is the phase-shifting cap mentioned above. A 0.01 uF cap is a great starting point, but you may try caps between 0.005 uF (5000 pF) and 0.022 uF. The smaller the cap, the sweeter the sound will be, but this really depends on your particular pickups. I recommend experimentation and fine-tuning to get as close as possible to a Strat's in-between tones.
As for the attenuation resistor, a 6.2k-ohm resistor works pretty well with the 0.01 uF cap and standard single-coil pickups. As a simple guideline, you can follow this rule by choosing and experimenting with this resistor: The higher the value, the more attenuation in the system, the smaller the impedance peak. A good starting point is the DCR of the pickup that's connected to the switch. For example, if your pickup measures a DCR of 6.8k ohms, you should start with a 6.8k-ohm resistor on the switch for a balanced sound and experiment from there. A good option is to use a small trim pot first so you can experiment until you find the value you like best. You can measure the trim pot and solder a fixed resistor with the measured value on the switch, or simply leave the trim pot where it is. A 10k or 15k trim pot is perfect for this.
That's it for this round. In honor of Fender's 75th Anniversary, next month we'll take a deeper look into Fender's history, busting some myths, misunderstandings, and urban legends, while celebrating the man behind the company that started it all: Mr. Clarence Leonidas Fender, or Leo Fender, as the world calls him.
Until then ... keep on modding!
- Mod Garage: “Jimmy Page” Les Paul Wiring - Premier Guitar ›
- Mod Garage: Adding an Out-of-Phase Switch to a Telecaster ... ›
- Phasing Out: How to get out-of-phase sounds from a Stratocaster ... ›
Brent Mason is, of course, on of the most recorded guitarists in history, who helped define the sound of most ’90s country superstars. So, whether you know it or not, you’ve likely heard Mason’s playing.
Professional transcriber Levi Clay has done the deepest of dives into Brent Mason’s hotshot licks. At one point, he undertook the massive project of transcribing and sharing one of Mason’s solos every day for 85 or so days. Mason is, of course, on of the most recorded guitarists in history, who helped define the sound of most ’90s country superstars. So, whether you know it or not, you’ve likely heard Mason’s playing. Levi shares the insight he gleaned from digging deep, and he tells us what it was like when they shared a stage last year. Plus, Levi plays us some great examples of Mason’s playing.
For the first time ever, two guitar greats, John 5 and Richie Kotzen will be heading out on the road this year. The tour will launch October 16 and run through November, hitting markets across the U.S.
Find the full tour itinerary right plus a link for tickets & VIP, including additional dates featuring John 5 only. Reserved seating tickets will go on sale Friday May 16 though a fan presale will begin today at noon local time and fans are strongly encouraged to buy early to get the best seats.
Meet and Greets for both artists will be available. For John 5 please go to: https://john5store.com/collections/vip.
Today, John 5 also announces more details of his anticipated new album. Called The Ghost, it will be released October 10 and is led by the new track “Fiend,” featuring Kenny Aronoff.
John 5 continues running public tours this month for his Knights In Satan’s Service Museum of KISS Memorabilia in Los Angeles, California. Guided tours are open to the public for one month only (with a possible expansion). Current dates available are May 12-16, May 19-23 and May 27-30. Each will be led by John 5 himself who will provide tons of rich detail and answer any questions. Secure your place HERE.
JOHN 5 continues to tour with Mötley Crüe including an upcoming residency in Las Vegas in 2025.RICHIE KOTZEN &
JOHN 5 FALL 2025 TOUR
October 16 El Cajon, CA @ Magnolia
October 17 Riverside, CA @ Fox Performing Arts
October 18 Roseville, CA @ Goldfield Trading Post
October 19 San Jose, CA @ The Ritz
October 21 Phoenix, AZ @ Celebrity Theatre
October 22 Albuquerque, NM @ KiMo Theatre
October 24 Dallas, TX @ Granada Theater
October 25 Leander, TX @ The Haute Spot
October 27 New Orleans, LA @ House of Blues
October 28 Memphis, TN @ Minglewood Hall
October 29 Nashville, TN @ Fogg Street Lawn Club
October 30 Atlanta, GA @ Variety Playhouse
October 31 Orlando, FL @ House of Blues
November 1 Fort Lauderdale, FL @ Culture Room
November 2 Clearwater, FL @ Capitol Theatre
November 4 Richmond, VA @ The National
November 5 Leesburg, VA @ Tally Ho Theater
November 6 Patchogue, NY @ Patchogue Theatre
November 11 Glenside, PA @ Keswick Theatre
November 12 Derry, NH @ Tupelo Music Hall
November 13 Foxborough, MA @ Six String Grill & Stage
November 14 Stroudsburg, PA @ Sherman Theater
November 15 Lorain, OH @ Lorain Palace Theatre
November 16 Columbus, OH @ The King Of Clubs
November 17 Warrendale, PA @ Jergels
November 19 Wyandotte, MI @ District 142
November 20 Flint, MI @ The Machine Shop
November 21 Fort Wayne, IN @ Piere’s
November 22 St. Charles, IL @ Arcada Theatre
November 23 Belvidere, IL @ Apollo Theatre
November 25 Denver, CO @ Oriental Theater
November 29 Pioneertown, CA @ Pappy & Harriet's*
*John 5 only
AEROSMITH guitarist and songwriter JOE PERRY is set to return to the road for a series of August performances with THE JOE PERRY PROJECT. The 8-date run kicks off August 13 in Tampa, FL and wraps August 23 in Port Chester, New York, with an August 19 performance in PERRY’s Boston hometown (see the itinerary below). For the North American trek—which marks the first solo shows for PERRY this year—the legendary guitarist will be joined by his Aerosmith bandmates Brad Whitford (guitar) and Buck Johnson (keys), along with The Black Crowes’ Chris Robinson (vocals), and Stone Temple Pilots’ Robert DeLeo (bass), and Eric Kretz (drums).
“Well…it’s time to let the music do the talkin again,” PERRY says. “I’m really excited about the JPP line up this year!!!! Most of these guys played with me at The Roxy in L.A. at the debut event for my latest solo album [Sweetzerland Manifesto] in January 2018. They’re all busy as hell but thankfully they’re able to carve out some time for this run. And I’m not only lucky enough to have Brad Whitford onstage with me but Chris Robinson of The Black Crowes! [who sang ‘Fortunate One’ on Sweetzerland Manifesto MKII], Robert DeLeo and Eric Kretz from STP!!! and Buck Johnson who plays keys and sings with Aerosmith, the Hollywood Vampires, and is also a solo artist in his own right.”
For the shows, the Rock and Roll Hall of Fame inductee says “the set list is gonna include my fav JPP cuts, STP, Black Crowes, and with Brad we’ll be hitting the Aero hits and some deep cuts and then ya never know!!!! Gonna be a BLAST, and if you’ve ever been to one of my shows you know the words GARAGE BAND on STEROIDS come to mind! See you there!!!!”
DATE | LOCATION | VENUE |
Wednesday, August 13 | Tampa, FL | Seminole Hard Rock - Tampa |
Thursday, August 14 | Hollywood, FL | Seminole Hard Rock - Hollywood |
Saturday, August 16 | Toronto, ON | HISTORY |
Sunday, August 17 | Muskoka, ON | Kee to Bala |
Tuesday, August 19 | Boston, MA | Wang Theatre |
Wednesday, August 20 | Hampton Beach, NH | Hampton Beach Casino Ballroom |
Friday, August 22 | Mashantucket, CT | The Premier Theater at Foxwoods Resort Casino |
Saturday, August 23 | Port Chester, NY | Capitol Theatre |
A sample page from the author’s analog log.
Seasonal changes are tough on your acoustic. Here’s how you can take better care of your prized instrument.
As you read this, spring is in bloom in most of the US, or maybe it has been for some time. I’m timing this column specifically to ask acoustic guitarists, in this season of increasing humidity and comfortable conditions, to prepare for what’s coming. It’s never too soon, and time flies. Before you know it, we’ll be back to the maintenance phase and you might be blowing up the phones of your local guitar shops, luthiers, and techs. I’m here to encourage a decidedly old-school approach to preventative guitar maintenance, and yes, it starts now.
Why, you ask? Well, as the lead luthier at Acoustic Music Works, I can tell you that in my nearly 15 years in this position, this was the worst winter ever for preventable repairs on acoustic guitars. Fret sprout, bridge lifts, top sink, soundboard cracks, back cracks, loose binding, general malaise… These hit us very hard in the winter that spanned 2024 and 2025. Am I complaining? On the one hand, no. This is part of how we make our money. On the other hand, yes! Repair schedules related to dryness and humidity issues can stretch into weeks and even months, and nobody wants to be without their favorite instruments for that amount of time. With a little thoughtfulness, however, you might get through next winter (and every one thereafter) without hefty repair bills or time apart from your musical companion.
Our preparation is going to start with an unlikely but very important guitar accessory: the humble notebook. Plain, lined, grid, day planner… it doesn’t matter. We all need to actively participate in our instrument maintenance, and in my experience, fancy apps that track humidity via Bluetooth breed a kind of laziness, a feeling of safety that might prevent us from actually physically looking in on conditions. Better we keep an analog, well, log, so that we know where things stand, and I suggest checking in daily.
“This was the worst winter ever for preventable repairs on acoustic guitars.”
Track your relative humidity, both in the case and in the room where your instruments mostly reside, but also take notes on your action height, top deflection (StewMac has some great tips for measuring this) and anything related to playability that you believe you can observe empirically.
Dryness is the root cause of most guitar issues that manifest in the fall and winter months. Symptoms of dryness include sharp fret ends, falling action and dead frets, sunken top around the sound hole, and cracks and bridge lifts. With your trusty notebook, you’ll get a feel for the sensitivity level of your instrument, and that knowledge is power!
A few other basic implements will not only assist you in your observations, but may also satisfy your need to buy guitar-related things (at least for a minute). Getting quick and comfortable with a fret rocker is a great skill to have, and is invaluable in diagnosing buzzes due to high frets or frets that have come unseated due to dryness. A well-calibrated relief gauge might seem luxurious, but it can prevent you from making unnecessary or extreme truss rod adjustments. A string action gauge, or even a simple machinist’s rule or set of feeler gauges, will help you keep track of your action. Get a three-pack of hygrometers so you can average their readings, rather than depending on one.
Lest we forget: A guitar can not only be too dry, it can also be too wet. By beginning your maintenance diligence in the spring/summer, you’ll also be able to tell if your instrument is the victim of a too-humid environment. The signs of over-humidification are subtle: Your action may rise from a puffed-up top, and in extreme cases, glue joints could begin to fail. In my experience, an over-humidified guitar will suffer from dulled tone, almost like a sock in the sound hole. If you’re sensing a lack of clarity in your guitar all of a sudden, start with new strings. If it persists, it might be due to over-humidification, and you may want to introduce a desiccant to the case for a time. The more lightly built your guitar is, the more sensitive it will be to seasonal changes.
By getting into these habits early, you’ll be empowered by knowing your instrument more intimately. You’ll understand when and why changes in tone and playability might have occurred, and you’ll hopefully save on repair bills year-round. Feel free to reach out with any questions. Who knows? I might just send you a notebook with an AMW sticker on the cover!