This Barney Kessel Custom ’burst is in exceptional condition, with a body that practically gleams. The only mod is one exchanged tuner and patches of old screw holes on the headstock.
From the sparse, smoky ballads of Julie London to the hard bop of Sonny Rollins, Barney Kessel could back up just about anybody. The bandleader, session great, Wrecking Crew member, and sideman was one of the most accomplished guitarists of his era. His chordal complexity not only got him steady work and accolades, but also a collection of signature guitar models bearing his name.
This 1968 Gibson Barney Kessel Custom is a top-of-the-line example. It’s the higher-end counterpart to the Barney Kessel Regular, both built from 1961 until 1974. They followed a trio of Barney Kessel signatures that Kay sold between 1957 and 1960.
Barney Kessels often became parts donors, with their hardware, tuners, and pickups (original PAFs, Pat. No., and T-Tops, depending on the year) being stripped and sold separately.
Each Gibson model has a hulking 17"-wide and nearly 3"-deep body, with two humbuckers, a Tune-o-matic bridge, and a bound rosewood fretboard. The attractive Barney Kessel tailpiece is also common to both, while the controls will be familiar to any Gibson player: two volume pots, two tone knobs, and a 3-way selector switch. The dual Florentine cutaways—a design first seen in these Barney Kessels and later used in Gibson’s Trini Lopez signature—cut a striking silhouette.
Of the two Gibson Kessels, the Custom alone is dressed to the nines, swapping in gold-plated hardware for the Regular’s nickel, and bowtie inlays for the Regular’s fretboard parallelograms. There’s also a 3-piece maple neck with two pinstripe-thin mahogany strips taking over for the Regular’s solid mahogany. And the Custom tops off its outfit with a pearl headstock inlay in the shape of a musical note.
Such features were a huge upgrade to the art-deco stylings and Kleenex-box pickups of Kay’s Kessel signatures, which Kessel snubbed, reportedly saying, “I don’t play that Kay. It’s a terrible guitar!” Interestingly, he often chose not to play these Gibson signatures, either, instead typically using his favorite 1940s ES-350.
When they were introduced, Gibson’s Barney Kessel Custom model had a list price of $599, while the Regular’s was $399. Both sold in respectable if not incredible numbers, with sales peaking in 1968. However, the following decades were not particularly kind to the guitars. As the vintage market took off for Les Pauls, SGs, and other classic Gibsons, Barney Kessels often became parts donors, with their hardware, tuners, and pickups (original PAFs, Pat. No., and T-Tops, depending on the year) being stripped and sold separately. You can still find Barney Kessel husks on the market—project guitars looking for a new owner to rebuild them. And many of the complete Barney Kessels you’ll find for sale have been rebuilt.
A rear view indicates this Kessel was not heavily played. There’s no belt rash, finish wear, or other marks, and the new-guitar tags typically indicate that the previous owner or owners had a collector’s sensibility.
That’s what makes the particular Barney Kessel Custom featured here so special. It’s nearly all original, with Patent pickups intact and even its Custom-stamped hang tags. The only modification is one replaced tuner (along with a couple patched screw holes from a previous replacement). The cherry in its cherry sunburst finish is one of the most vibrant we’ve ever seen, and the condition of the finish overall is in impeccable vintage shape.
This Custom model is classic Gibson, with its 4-knob control array, 3-way toggle, and Pat. No. pickups. Unique flourishes include the special Barney Kessel tailpiece and bow-tie fretboard inlays.
Because of the wide array of Barney Kessel Customs on the used market—many with non-original parts—you can find them across the price spectrum, from about $3,000 on the low-end to $12,000 or more on the high. This Custom, listed on Reverb now by Nationwide Guitars, fittingly lands on the higher end, with an asking price of $8,999.
Sources for this article include Gruhn’s Guide to Vintage Guitars by George Gruhn and Walter Carter, American Guitars: An Illustrated History by Tom Wheeler, Reverb’s “Player Profile: The Hard-Swinging Barney Kessel” by Greg Cooper, Premier Guitar’s “Gibson and Barney Kessel” by Jim Bastian, and Reverb listings from Retrofret Vintage Guitars and Vintage Correct Parts.
- 'Reunion!' Bruce Forman's Love Affair with Barney Kessel's Guitar ... ›
- A Burst From a Different Golden Era - Premier Guitar ›
- 1967 Gibson Trini Lopez Deluxe and 1968 Gibson Barney Kessel ... ›
This month’s mod Dan’s uses a 500k linear pot, a 1.5H inductor (L) with a 0.039 µF (39nF) cap (C), and a 220k resistor (R) in parallel.
Don’t let the name fool you, this is a purely passive device—nothing is going to be boosted. In general, you can’t increase anything with passive electronics that isn’t already there. Period. But you can reshape the tone by deemphasizing certain frequencies and making others more prominent (so … “boost” in guitar marketing language). Removing highs makes lows more apparent, and vice versa. In addition, the use of inductors (which create the magnetic field in a guitar circuit) and capacitors will create resonant peaks and valleys (bandpasses and notches), further coloring the overall tone. This type of bandpass filter only allows certain frequencies to pass through, while others are blocked, and it all works at unity gain.
“You can’t increase anything with passive electronics that isn’t already there … but you can reshape the tone by deemphasizing certain frequencies and making others more prominent.”
All the systems I mentioned above are doing more or less the same thing, using different approaches and slightly different component values. They are all meant to be updated tone controls. Our common tone circuit is usually a variable low-pass filter (aka treble-cut filter), which only allows the low frequencies to pass through, while the high frequencies get sent to ground via the tone cap. Most of these systems are LCR networks, which means that there is not only a capacitor (C), like on our standard tone controls, but also an inductor (L) and a resistor (R).
In general, all these systems are meant to control the midrange in order to scoop the mids, creating a mid-cut. This can be a cool sounding option, e.g. on a Strat for that mid-scooped neck and middle tone.
Dan Torres offered his “midrange kit” via an internet shop that is no longer online, same with his business website. The Torres design is a typical LCR network and looks like the illustration at the top of this column.
Dan’s design uses a 500k linear pot, a 1.5H inductor (L) with a 0.039 µF (39nF) cap (C), and a 220k resistor (R) in parallel. Let’s break down the parts piece by piece:
Any 500k linear pot will do the trick, in one of the rare scenarios where a linear pot works better in a passive guitar system than an audio pot.
(C) 0.039µF cap: This is kind of an odd value. Keeping production tolerances of up to 20 percent in mind, any value that is close will do, so you can use any small cap you want for this. I would prefer a small metallized film cap, and any voltage rating will do. If you want to stay as close as possible to the original design, use any 0.039 µF low-tolerance film cap.
(L) 1.5H inductor: The original design uses a Xicon 42TL021 inductor, which is easy to find and fairly priced. This one is also used in the Bill Lawrence Q-Filter design, the Gibson standard Varitone, and many other systems like this. It’s very small, so it will fit in virtually every electronic compartment of a guitar. It has a frequency range of 300 Hz up to 3.4 kHz, with a primary impedance of 4k ohms (that’s the one we want to use) and a secondary impedance of 600 ohms. Snip off the three secondary leads and the center tap of the primary side and use the two remaining outer primary leads; the primary side is marked with a “P.” On the pic, you can see the two leads you need marked in red, all other leads can be snipped off. You can connect the two remaining leads to the pot either way; it doesn’t matter which of them is going to ground when using it this way.
Drawing courtesy of singlecoil.com
(R) 220k: use a small axial metal film resistor (0.25 W), which is easy to find and is the quasi-standard.
Other designs use slightly different part values—the Bill Lawrence Q-filter has a 1.8H L, 0.02 µF C and 8k R, while the old RA Gresco Tone Qube from the ’80s has a 1.5H L, 0.0033 µF C, and a 180k R, so this is a wide field for experimentation to tweak it for your personal tone.
This mid-cut system can be put into any electric guitar not only as a master tone, but also together with a regular tone control or something like the Fender Greasebucket, or it can be assigned only to a certain pickup. It can be a great way to enhance your sonic palette, so give it a try.
That’s it! Next month, we’ll take a deeper look into how to fight feedback on a Telecaster. It’s a common issue, so stay tuned!
Until then ... keep on modding!