Here’s how to adapt the cool humbucker coil-splitting scheme found in Fender’s Select Carved Top Jazzmaster to your guitar.
Recently a customer brought in his Fender Select Carved Top Jazzmaster to get set up for heavier strings. This model has a simple layout: two humbuckers designed to look like vintage Wide Range pickups, a Gibson-style 3-way pickup selector switch, and a classic Telecaster control layout consisting of master volume and master tone. The 3-way switch was configured like a Telecaster with the familiar switching matrix of bridge, bridge-plus-neck in parallel, and neck positions. It was a rock-solid guitar that played well.
The owner pointed out that the tone control had an additional switch to split the humbucker pickups. (This turned out to be Fender's S-1 switch.) He then requested an additional switch to flip from parallel to series in dual-pickup mode for some ultra-fat lead tones. While talking about this option, he mentioned he'd never played a humbucker guitar that offered such a cool single-coil tone when in split mode—sparkle and shimmer without hum and noise.
I became curious. My first thought was that Fender simply connected both humbucker coils in parallel, rather than shunting one coil to ground when in split mode. As you may know, when using this option, the humbucking feature is still engaged and you receive a pseudo-single-coil tone without hum and noise. Most humbuckers don't sound like real single-coils in this mode. Some say this configuration sounds more like a P-90, while others say it sounds like a cheap, thin humbucker. But I kept my customer's remarks in mind when I started working on his guitar several days later.
Because the electronic compartment of this Jazzmaster opens from the back, like on a Les Paul, I decided to do all the other work first, such as making a new nut and doing a complete setup for the heavier strings. When it came time to perform the electronic upgrade, I was surprised when I investigated the wiring.
After analyzing the wiring more closely, I realized what we had here: an adaptation of a wiring Bill Lawrence developed in the late '80s.
In addition to a resistor connected to the S-1 switch, I found a capacitor wired to it. Clearly, I had to dig deeper into this wiring, so I requested the schematic (Image 1) from Fender. Thanks to my friend Brett Leasure for immediately sending it over.
The 0.1 µF capacitor and standard 1.5k-ohm resistor rang a bell. After analyzing the wiring more closely, I realized what we had here: an adaptation of a wiring Bill Lawrence developed in the late '80s. Though this isn't new, it remains a very effective hum-reducing scheme. Let's see how it works and what it's doing.
When splitting a humbucker to emulate single-coil tone, one of the coils will typically be shunted to ground, leaving the other coil active with all the hum and noise that's associated with a single-coil pickup. That holds true for this specific wiring, but the two humbucker wires that are wrapped together are not directly connected to ground. Instead, they run through an additional RC network (0.1 µF C plus 1.5k R in series). In this network, the capacitor plays the most important role.
Image 1
The cap shifts the resonance frequency of the coil that's sent to ground, moving it down to near the typical 50/60 Hz hum territory. But that's not all—it also shorts out the frequencies we hear as tone. For the hum frequencies, the coil that's sent to ground is still active, but the tone frequencies—those located above the hum frequencies—no longer exist. In layman's terms: The pickup still operates like a humbucker (i.e., both coils are active) in the frequency realm of hum and noise. Yet for all tone frequencies, we're essentially in single-coil mode. The additional resistor mutes the superelevation resonance of the coil that's sent to ground. So this clever little trick works much like a "virtual dummy coil" when the humbucker is in split mode.
In a way, we can say we're abusing one of the coils by diminishing the mids and treble using a series RC network connected in parallel to the coil. The coil still "sees" the bass and hum and noise frequencies, and acts like a virtual dummy coil with the other fully active coil. This was Bill Lawrence's basic idea that Fender adapted to their wiring for this Jazzmaster.
As always with analog technology, there's no distinct separation at, say, 70 Hz. The virtual dummy coil covers the whole range of hum frequencies, but is also partly active above these frequencies, and it uncouples slowly. To create credible single-coil tone, the mids and treble must be uncoupled. The resistor is important because it allows an even transition when uncoupling the capacitor, so both components work together. This interdependence opens the door to experimentation.
Let's see what it takes to transfer this special Jazzmaster wiring to your humbucker-equipped guitar. We'll do this by transferring the S-1 switching matrix to a push/pull or push/push volume pot with a common DPDT switch that's connected to a humbucker for splitting.
- The voicing of the single-coil emulation (governed by the cap's value).
- Hum-cancelling effectiveness (governed by the cap's value).
- Voicing of the cap's uncoupling range (governed by the resistor's value).
So as not to bore you with analog-system theory, I'll simplify some explanations that aren't critical to this mod. One common question is about the order used to connect the cap and the resistor in series. Actually, it doesn't matter, but from a theoretical point of view, electromagnetic compatibility (EMC) states the cap should be connected to ground as shown in Image 2.
I'm using the Seymour Duncan humbucker color code for this illustration. If you have a humbucker with a different color code, this should be easy to transfer. Of course, you can only split a humbucker when it has 4-conductor wiring that provides access to the start and finish of each of the two coils. If you have a humbucker with the standard 2-conductor wiring, you'll have to convert it to 4-conductor specs. Have this done by a qualified guitar tech or simply buy a new humbucker that comes stock with 4-conductor wiring. Let's see what happens when you tinker with the values of the two components.
Resistor.
Fender's 1.5k resistor creates a little hole (about -5 dB) in the mids, at around 2 kHz. Depending on the pickups and the amp, this can sound good. But when using Fender blackface amps, this isn't as desirable because of their inherent scooped midrange. Increasing the resistor value to 3.5k will eliminate the little hole in the mid frequencies. My personal favorite value is 3.9k ohm, which yields absolutely no mid hole. If you want more choices, you can wire a switch with two different resistors (for example, 1.5k and 3.9k) or use a 5k linear pot for a stepless control of this factor.
Capacitor.
The cap's capacitance lets us influence two factors, and we can deduce a relationship between them:- The smaller the capacitance, the better the hum-cancelling feature.
- The higher the capacitance, the better the single-coil emulation.
Here's a way to understand the cap's function in this wiring:
As the cap's value drops to zero, it's effectiveness is reduced. Zero capacitance is the same as using this wiring with no cap at all. With very high capacitance values, the coil will be shorted out more and more, until it is completely shorted, leaving only one coil still active.
A good range of cap values is from 0.01 µF up to 0.1 µF. You can use these—and everything in between—to balance the relationship between hum-cancelling and tone. The Fender value of 0.1 µF will result in maximum single-coil-like tone with a bit of hum cancelling—still much more than without the additional RC network. A 0.01 µF cap will result in a very high hum-cancelling ability (almost 40 dB), but with a tone that's quite fat and closer to a humbucker than a single-coil (think P-90 through a warm tube amp).
Explore these cap values, combined with resistor values from 1.5k up to 5k ohm, to dial in the midrange behavior. This will keep you busy for hours! For even more flexibility, you can implement a rotary switch with several cap values and a switch to turn the complete RC network on or off.
All this can be applied to our Fender wiring. Its stock values guarantee maximum single-coil emulation, but the downside—perhaps not for you—is less hum-cancelling and a tone that exhibits a midrange scoop. I think changing the values to a 3.9k resistor with a 0.047 µF cap will result in an authentic single-coil-like tone with no midrange cut, but with the benefit of greater resistance to hum and noise. In the end, it's about finding the right compromise, so experiment with the values of these two components to find a tone you love.
I'll be back with another project next month … until then, keep on modding!
[Updated 9/27/21]
- Mod Garage: Telecaster Series Wiring - Premier Guitar ›
- Mod Garage: The Fender Greasebucket Tone Circuit - Premier Guitar ›
- Strat Series Wiring for a New Decade - Premier Guitar ›
- Mod Garage: Telecaster Series Wiring - Premier Guitar ›
- Mod Garage: Telecaster Series Wiring - Premier Guitar ›
- What Does Phase and Polarity Mean for Your Guitar’s Pickups? - Premier Guitar ›
- Assessing a Pickup’s Polarity and Phase ›
- Is a Variable Dummy Coil the Solution to Single-Coil Hum? ›
With features like volume and gain controls, sparkle switch, and waveform shape control, these pedals are designed to be a must-have for any guitarist.
The Creamsicle has that low-gain English rock tone you've been looking for. It’ll remind you of that JCM45 that you deeply regret selling during the hair metal years, but it’s a lot lighter and can get that tone at a much lower volume. Gain and Volume controls, along with tone control, sparkle switch, and a three-position pre-amp gain switch. Go from 'creamy' to 'crunchy' with a twist of the dial and the flick of a switch. Try it with your favorite fuzz for even more - just like you did with that half-stack back in 1966.
Terrain
The Terrain is a tremolo with a difference: Its circuitry is designed to be as open and HiFi as possible. It features optical coupling to keep Low-Frequency Oscillator (LFO) noise out of the audio path. In addition to Speed and Depth controls it also features a waveform shape control to fine-tune that throb. It includes a gain control to make up for any perceived volume loss at high Depth settings. But most importantly, it features high input impedance, low distortion, full bandwidth, low noise, and high fidelity circuitry that stays crystal clear. You’re going to love it.
The Creamsicle features:
- Classic 1960’s English rock tone.
- Volume and Gain controls.
- Two-pole tone control.
- Sparkle switch.
- Three way preamp gain switch.
- Full bypass (of course).
- 9VDC, 31mA.
- MAP price: $145
The Terrain features:
- Optical tremolo for perfect LFO / audio isolation.
- High input impedance, full bandwidth, low noise, crystal clear signal path.
- Speed, Depth, and Waveform controls.
- Makeup Gain control.
- Full bypass (naturally).
- 9VDC, 32mA.
- MAP price: $145
Mayfly Creamsicle Overdrive and Terrain Tremolo - YouTube
Baroni Recording Amps: Faithful tone to iconic amps in rock history. High-Voltage Class A tube preamp and analog simulation for direct FOH or DAW use. VARICAB circuit for realistic cab simulations. Perfect for pedal demos and connecting pedalboard to DAW.
Baroni (A Foxgear Brand) Is proud to introduce its first range of Recording Amps with a range of five products designed to replicate five of the most iconic amps in rock history, including Fender, Marshall, Hiwatt, Orange and Vox. Each Baroni Recording amp is made of a High-Voltage Class A tube preamp and a renewed analog simulation that mimics all the chain after the preamp such as the power section, the speaker, the microphone, and preparing the signal in a 100% analog way to go direct to FOH console, or into the Audio Interface of your DAW. Thanks to the VARICAB circuit, introduced last year into Foxgear’s Miniamp series, and recently updated, and thanks to two separate control of Gain (Body) and Volume on the preamp section, you can truly mimic the behavior of the real amplifier, including the grit or bottom-end/punch usually added by the power tubes before to go to the XLR balanced out with a faithful recreation of your favorite sound with a big advantage: Eating Pedals perfectly.
Each Recording Amp also boasts a series fx loop, and a traditional TS Jack out to use as a standard preamp going into the return section of an amp, or into a power amplifier.No dozens of options, just pure tone straight to the point to not compromise the easy to use with pedals. Some YouTubers have already ordered their one to be used as their main interface to do pedal demos.
Baroni Preamps/D.I. Recording Amps Highlights include:
- Faithful tone to the original Amplifier
- 100% Analog signal path and Cab Simulation- Infinite and real-time changing cab simulations with VARICAB
- The definitive device to connect your pedalboard to your DAW without compromises.
For more information, please visit foxgeardistribution.com.
Crafted for comfort and ready to rumble, the potent and flexible Ultra II Meteora shatters the Fender offset mold.
Built for players boldly seeking the best, American Ultra II is our most advanced series of instruments. American Ultra II guitars and basses feature premium materials, precision craftsmanship and cutting-edge design for instruments that both advance the state-of-the-art and stand the test of time.
The Fender American Ultra II Meteora features a select alder body with sculpted body contours. For effortless playability, the quartersawn maple neck features our Modern D profile and smooth Ultra Satin finish. Ebony or quartersawn maple 10”-14” compound radius fingerboards feature Ultra rolled edges, medium-jumbo frets, Luminlay side dots and Graph Tech TUSQ nuts. The tapered neck heel and sculpted body contours allow unparalleled access to the higher register.
Under the hood, a pair of Haymaker humbuckers deliver everything from sweet cleans to modern crunch and searing leads, all without a hint of hum. Our patented S-1 switch cleverly splits the Haymakers for even more tonal variety, and you can further sculpt your tone with both conventional master tone control plus a carefully voiced bass cut knob. Additional road-ready features include 6-saddle string-through-body hardtail with polished stainless steel block saddles, deluxe locking tuners, knurled aluminum knobs and 1-ply anodized aluminum pickguard.
The American Ultra II Meteora infuses iconic style with advanced appointments to take your playing to stratospheric new heights. For players who demand flawless tone, infinite versatility and limitless performance, American Ultra II delivers.
Learn more here.
Fender American Ultra II Meteora Electric Guitar - Texas Tea, Ebony Fingerboard
Am Ultra II Meteora, Texas TeaPG's host straps on a prototype Tele to unleash the Knife Drop's horror and heft only to dismantle Jack White's Triplecaster in one accidental Bigsby bomb.