
A client wanted her D-12-20 to fret in tune all along the fretboard. Can it be done?
Intonating a flattop’s bridge saddle is tricky, and that’s especially true when it comes to vintage 12-string guitars. Back in the day, it was rare to find an acoustic 12-string with a compensated bridge saddle. In fact for many players, the slightly out-of-tune jangle was a big part of a 12-string’s aural mystique. But times have changed, and as music and recording technology have evolved, most musicians and producers expect a 12-string to play reasonably in tune all along the fretboard.
Intonating a flattop 12-string with a straight bridge saddle involves filing unique break angle and intonation points for each string—an operation that requires skill and patience. Let’s investigate and see exactly what’s involved.
We’ll use a beautiful 1972 Martin D-12-20 as our project guitar. The guitar was in good shape when its owner brought it into the shop, but it didn’t play even remotely in tune and the action was uncomfortably high. Many old 12-strings require a neck reset (an expensive proposition), but I checked the neck angle and it was fine. Fortunately for the guitar’s current owner, the problem was rather simple. Somewhere along the line a previous owner or tech had installed a saddle that was both too high and incorrectly radiused (Photo 1).
My job was twofold: lower the action by reshaping the bridge saddle and then intonate each string. I knew that once I completed these tasks, the D-12-20 would play better than ever and sound more in tune at the higher frets.
Requisite tools. To intonate a 12-string, you need a few specialized luthier tools. These include a string action gauge, radius gauges, and a radius block (the latter must match the fretboard radius). You’ll also need a mechanical pencil, a capo, self-adhesive 80-grit and standard 400-grit sandpaper, and flat, single-cut miniature needle files.
You can estimate where each string should rest on the saddle, but it’s nearly impossible to get it perfect on the first try.
Preliminary check. Before starting this kind of work on a guitar, it’s important to tune to concert pitch and take measurements. These specs provide a baseline to help gauge your progress. You’ll be taking several measurements, so write them down as you go.
First, put a capo on the 1st fret and measure action at the 12th fret with a string action gauge. Take this measurement for both the 1st and 11th strings—the first of the doubled high Es and the low E string. (We’ll assume your 12-string has the standard octave-string configuration, i.e., the octaves in each pair are closer to you than their wound partners. Some electric 12s, notably Rickenbackers, reverse this order.) Measure the distance between the bottom of the string and the top of the 12th fret.
Next measure the relief: With the capo still on the 1st fret, hold the 11th and 12th strings down at the 14th fret and measure the greatest gap between the bottom of the 11th string and the top of the frets. Typically this occurs around the middle of the fretboard, somewhere between the 7th and 9th frets. You can identify this gap by tapping the 11th and 12th strings against the frets while still pressing them down at the 14th fret.
Now remove the capo and check the action at the 1st fret.
Finally, using a strobe tuner, check the intonation for each string. (Naturally, this is tricky on a 12-string because you have to pluck each individual string of the six pairs.) Starting with the 1st string, play the 12th-fret harmonic—make sure it’s in tune—and then fret the same note. If the fretted note is sharp or flat compared to the reference harmonic, write down how many cents it’s off and in which direction. Repeat the process until you’ve documented the intonation at the 12th fret for all 12 strings.
Our 12-string’s preliminary specs. Here’s how the D-12-20 measured up: The action at the 12th fret was 6/64" for the 1st string and 7/64" for the 11th string. Too high to play! The relief was .012"—perfect for my client’s playing style. At the 1st fret, the 1st string was 1/64" and the 11th string was just over 2/64" above the fret. Again, perfect action at the string nut. At this point, I knew my job would simply entail lowering the action at the bridge saddle.
When I checked the intonation with a strobe tuner, and compared the 12th fret harmonics to their corresponding fretted notes, I found most of the fretted notes were from two to six cents sharp, although the G and D pairs were flat by about three cents.
With these measurements in hand, I was ready to get to work.
Photo 2
Sanding the bridge saddle. My next step was to check if the saddle’s radius matched the fretboard radius. My radius gauge revealed what I’d suspected—it wasn’t even close. The fretboard had a 14"radius (Photo 2), but the bridge saddle was around 8". This meant the saddle had a much more pronounced arch than the fretboard. I knew if I didn’t reshape the top of the saddle to match the fretboard, the D and G pairs would be radically higher than the other strings.
Photo 3
Using a 14" radius block and self-adhesive 80-grit sandpaper, I sanded the top of the saddle until it matched the block’s radius. Here’s the most accurate way to reshape the top of the saddle: Place the radius block in a vise with the radius side up and affix the self-adhesive sandpaper to the block. Now remove the saddle from its bridge slot, turn it upside down, and gently sand its top in the block’s concave area. If you shine light behind the saddle, you’ll be able to see how much material you’re removing from the saddle and make sure its radius matches the block (Photo 3).
Since the action was pretty high on our 12-string, I removed about 1/32" from the top of the saddle at both E string pairs. I removed quite a bit more from the middle of the saddle to flatten out the arch.
Once the saddle is correctly radiused, slip it back into the bridge and grab your mechanical pencil.
Photo 4
Marking the saddle. Now it’s time to draw guidelines on the saddle crown for both the individual intonation points and the various angles needed to guide the strings as they emerge from the pin holes (Photo 4). But before you start drawing lines, let’s take a moment to discuss where the strings should sit on the top of the saddle. First we’ll deal with the intonation points, then the string angles.
Fair warning: Setting the intonation entails some trial and error. You can estimate where each string should rest on the saddle, but it’s nearly impossible to get it perfect on the first try.
For this task, it’s helpful to mentally divide the 12 strings into three groups:
• The six E, A, D, G, B, and E strings you’d find on a regular flattop. We know the lowest four are wound, and the top two are plain. So far, so good.
• The plain octave strings (E, A, D, G) that pair with the wound E, A, D, and G strings.
• The doubled unison B and high-E strings. Just like their mates, these are plain.
Okay, think about the first group—our standard 6-string. As a general rule, both the low E and B strings intonate best at the rear edge of the saddle (closest to the bridge pins). The G string’s intonation point is typically at the very front of the saddle (closest to the soundhole).
That leaves the high E, D, and A strings to be accounted for. The high E will typically fall between the B (remember, that’s at the rear of the saddle) and the G (at the front of the saddle). The D and A strings usually create a stair-step pattern between the G and low E strings, with the D closer to the G, and A closer to the low E.
The four plain octave strings are a different story. Both the low E’s octave and the G’s octave points will be at the front of the saddle. The octave strings for A and D will be further back toward the bridge pins.
As you’d expect, the unison B and E strings sit at exactly the same point as their siblings.
Now consider how each string travels from the pin hole in the bridge to the top of the saddle—the intonation point. On this Martin, the six primary strings—those that correspond to a standard flattop—are set back toward the rear of the bridge. The six additional strings, the four octaves and two unisons that make a 12-string such a beautiful beast, emerge through the soundboard and bridge right behind the saddle.
On the rear of the saddle, you need to file individual angles (think of them as ramps) that allow each string to reach its intonation point without encountering a sharp edge. Correctly filed angles minimize string breakage and maximize sustain. The angle for the primary strings will be shallower than the six extra strings.
Photo 5
On the rear of the saddle, you need to file individual angles (think of them as ramps) that allow each string to reach its intonation point without encountering a sharp edge. Correctly filed angles minimize string breakage and maximize sustain. The angle for the primary strings will be shallower than the six extra strings.
Filing the saddle. This is where your inner artist gets a chance to shine. Using a miniature flat file, carve each string’s intonation point and rear angle, based on your markings (Photo 5). Go slowly, and to prevent any sitar-like buzzing, be sure each string leaves the saddle from a crisp, defined peak as it heads toward the soundhole.
Checking intonation. As I mentioned earlier, there’s a lot of trial and error involved with intonating a 12-string. Once you’ve done the first pass of filing, put on a fresh set of strings, tune them to pitch, and check the intonation.
Photo 6
The goal is to have the fretted note at the 12th fret match the corresponding 12-fret harmonic. Use a tuner to keep track of how close the fretted note comes to its reference harmonic. If the string frets sharp, file the intonation point back toward the rear of the saddle. Conversely, if the fretted note is flat, carve the intonation point forward toward the front of the saddle. When you’re done, the saddle should look similar to Photo 6. Don’t be dismayed at how many times you’ll need to slacken and remove the strings, file the saddle, restring, retune, and recheck the intonation.
Wrap it up. When you’ve got the intonation dialed in to your satisfaction, take off the strings one last time, pop out the saddle, and then polish it with 400 grit sandpaper, followed with a polishing cloth. Restring, retune, and you’re good to go.
This process takes a long time to master, but in the end, it’s worth it when your 12-string plays in tune all the way up the neck.
Watch the official video documenting the sold-out event at House of Blues in Anaheim. Join Paul Reed Smith and special guests as they toast to quality and excellence in guitar craftsmanship.
PRS Guitars today released the official video documenting the full night of performances at their 40th Anniversary celebration, held January 24th in conjunction with the 2025 NAMM (The National Association of Music Merchants) Show. The sold-out, private event took place at House of Blues in Anaheim, California and featured performances by PRS artists Randy Bowland, Curt Chambers, David Grissom, Jon Jourdan, Howard Leese, Mark Lettieri Group, Herman Li, John Mayer, Orianthi, Tim Pierce, Noah Robertson, Shantaia, Philip Sayce, and Dany Villarreal, along with Paul Reed Smith and his Eightlock band.
“What a night! Big thanks to everyone who came out to support us: retailers, distributors, vendors, content creators, industry friends, and especially the artists. I loved every second. We are so pleased to share the whole night now on this video,” said Paul Reed Smith, Founder & Managing General Partner of PRS Guitars. “I couldn’t be more proud to still be here 40 years later.”
With nearly 1,400 of the who’s who in the musical instrument industry in attendance, the night ended with a thoughtful toast from PRS Signature Artist John Mayer, who reflected on 40 years of PRS Guitars and the quality that sets the brand apart. “The guitars are great. You can’t last 40 years if the guitars aren’t great,” said Mayer. “Many of you started hearing about PRS the same way I did, which is you would talk about PRS and someone would say ‘They’re too nice.’ What’s too nice for a guitar? What, you want that special vibe that only tuning every song can give you on stage? You want that grit just like your heroes … bad intonation? The product is incredible.”
Black Sabbath to Reunite for First Time in 20 Years—Ozzy Osbourne’s Final Performance
The original Sabbath lineup will reunite on July 5 in Birmingham, England, and be joined by Metallica, Pantera, Slayer, and more.
The concert will feature founding members Tony Iommi on guitar, bassist Geezer Butler, drummer Bill Ward, and singer Ozzy Osbourne. Profits from the show, called "Back to the Beginning," will be donated to charities including Cure Parkinson's.
On future Black Sabbath plans, Ozzy's wife, music manager, and TV personality Sharon Osbourne had this to say (via Reuters) about Ozzy: “While other bandmembers might continue to make records and perform, Black Sabbath's gig at the birthplace of the band will certainly be the 76-year-old's final performance.
"For Ozzy right now, it's definitely: 'I love you and good night'," she said.
The shredder and son of legendary artist Frank Zappa gives a tour of his up-to-date gear, including a complex stereo switching system, four racks of pedals, and some of his father’s favorite guitars.
Dweezil Zappa was always going to end up being an incredible guitarist. His dad, Frank Zappa, is celebrated as one of the most talented and creative guitarists in history, and by age 12, Dweezil was recording music produced by Eddie Van Halen. (Little surprise that he’s covering Van Halen’s 1981 stunner “Push Comes to Shove” lately.) He’s been a bona fide guitar star ever since, releasing seven original solo records, six tribute records, two LPs with his brother Ahmet Zappa, and guesting on recordings across the music universe.
Ahead of his gig at Memphis’ Minglewood Hall on his 2024 Rox(postroph)y tour, which celebrated the 50th anniversary of Frank Zappa’s Apostrophe (') and Roxy & Elsewhere records, Dweezil gave PG’s John Bohlinger a boot-to-bonnet look at his current road setup. There’s a lot of ground to cover between his and his father’s catalogues, and Dweezil loves the challenge, which he meets with a mix of his own gear and some special vintage assists courtesy of his dad.
Brought to you by D’Addario.Shut Up ’n Play Yer Les Paul
This coveted Gibson Les Paul Custom, featured on the cover of Frank’s 1981 record Shut Up ’n Play Yer Guitar, came out on the road this tour. Dweezil says that around 1986, his dad swapped in Dan Armstrong-made ceramic pickups. At one point, Frank installed a second input to try to use the guitar as a synth controller, but it didn’t track well enough to continue the experiment.
Along with the standard controls, the guitar includes switches to turn on different parts of the onboard preamp, which boosts the signal and adds plenty of gain. A rotary knob controls a wired-in parametric EQ set up to emulate different settings along the sweep of a wah pedal. Dweezil didn’t get much of the lowdown from his father on the complex operations; it was more trial-and-error. “You just have to turn knobs until you find something that you like,” he says. He connects to his rig with ZZYZX SnapJack magnetic cable connectors.
Rockin' with Roxy
Also out on the Rox(postroph)y tour is Frank’s iconic Roxy & Elsewhere-era Gibson SG. Like the Les Paul, it’s got a preamp circuit to boost the signal, a sweepable EQ, and can achieve acoustic, piezo-adjacent sounds. The preamp configuration in this one is red-hot; it dishes out tons of gain.
Signature Shabat
For Strat-style tones, Dweezil calls on his signature Shabat Lynx DZ, which has been used to dial in his cover of “Push Comes to Shove.” Per Shabat, it has a “body-mounted HSS configuration with a push/pull phase shift on the middle pickup, simplified single-knob layout, custom-cut 3-ply parchment/gold pickguard, and … a Vega-Trem VT1 tremolo."
The Lynx DZ is constructed with an alder body and a quartersawn hard maple, medium-C-profile neck with a 25.5" scale length. It’s loaded with Lollar Special S and Lollar El Rayo pickups, and the middle Special S is wired for phase shift. The Lynx, as well as the SG and Les Paul, are strung with Optima Gold-Plated 2028 FZ Frank Zappa strings (.008–.046), and struck with D’Addario .50 mm celluloid picks. (Dweezil likes them for pick slides.)
On the Ground
Zappa keeps a significant board at his feet, which he controls with a Fractal FC-12 controller. He runs his sound in stereo, with different effects going to each side, so he keeps volume pedals for each side in front of him, plus a wah and expression pedal.
The row of pedals perched atop the pedalboard includes a TC Electronic Polytune 3 Noir, a Marshall-style prototype pedal, J. Rockett Audio Designs PXO, Union Tube and Transistor Lab, SoloDallas Orbiter, a Jext Telez White Pedal (to nab a specific tone for playing “Nanook Rubs It”), and a 29 Pedals FLWR.
In the Rack
On our 2013 Rig Rundown, Dweezil was using the Fractal Axe-Fx II, and this time around, he’s upgraded to the Axe-Fx III as the basis of his sound. Given the sonic territory covered in his shows, it simply became too unwieldy and expensive to tour an analog rig.
The brains of his show are held in a rack system. A couple of out-of-sight splitter boxes help with the complex stereo signal paths, as do a pair of Voodoo Lab HEX audio switchers. The Axe-Fx III lives on the top shelf, and just below it are an Eventide H90 and TC Electronic TC 2290 that go to both sides.
The next rack down runs only to the left side, and includes a BK Butler Tube Driver, DigiTech FreqOut, Red Panda Radius and Raster, Krozz Devices Airborn Analog Flanger, and a Paul Trombetta Design Tornita! fuzz.
The level below it runs to the right side, with a “Clown Vomit” fuzz, Chase Bliss Warped Vinyl, Korg FLG-1 Flanger, Chase Bliss Generation Loss, Goochfx Holy Cow, and another Red Panda Raster.
Wrapping up the rig is the bottom rack, which again runs to both sides. It carries most of Zappa’s exquisite dirt sounds, thanks to a Union Tube and Transistor Tsar Bomba, Chase Bliss Automatone Preamp MKII, Goochfx Dirty Hippie, Tru-Fi Two Face, Foxrox Electronics Paradox TZF2, and a Paul Trombetta Design Rotobone that … somewhat reasonably apes a trombone sound. Paul Trombetta, we salute you.
Kepma Guitars introduces the new Fenix Series of Grand Auditorium acoustic guitars, offering premium features at an entry-level price, plus their new travel-sized FC Mini Series.
Designed for both aspiring players and seasoned musicians, the Fenix Series offers premium features typically found in higher-priced instruments, all starting at just $249.99.
“The new Fenix models represent our commitment to making premium-quality guitars accessible to players at every level, without compromising on sound, playability, or innovation,” said Kepma USA president Tony Moscal. “With their torrefied solid tops, thinner neck profiles, and unparalleled playability, these guitars deliver exceptional sound and feel typically reserved for professional instruments—all at an entry-level price.”
The Kepma Fenix Series features a Grand Auditorium body style with a solid torrefied Sitka spruce top, delivering exceptional tonal resonance and stability. The proprietary Kepma Torrefication Process uses a precise combination of heat and humidity to remove moisture, oils, and sap from the wood, resulting in a stronger, more stable top that enhances string vibration and ensures consistent performance in any environment.
Back and sides are crafted from layered African mahogany, providing a warm, balanced sound. The neck, made of durable nato wood, is reinforced with a two-way adjustable truss rod and finished with a smooth satin coating for effortless playability.
The Fenix Series is packed with cutting-edge features to elevate the playing experience:
- New 4-Point Bolt-On Neck Joint: Ensures unparalleled stability that allows for easy adjustments and maintenance - a first at this price point.
- Ultra-Thin Water-Based Finish: Environmentally friendly and just 0.042mm thick, this finish protects the guitar while maximizing tonal projection and preserving the natural beauty of the wood.
- Beveled Binding for Comfort: High-quality ABS beveled binding enhances durability, prevents edge damage, and ensures a comfortable playing experience.
- C-Shaped Fast Neck: A player-friendly design that reduces hand fatigue, enhances playing fluidity, and supports all playing styles.
For players seeking even more versatility, the optional AcoustiFex K-10 Pro Pickup, Preamp & FX System transforms the Fenix into an all-in-one performance and practice powerhouse. This system includes built-in reverb, delay, and chorus effects, Bluetooth audio streaming, and a companion app for rhythm looping, metronome functions, and more. Whether you’re performing on stage or practicing at home, plugged into an amp or mixer, or simply playing unplugged, the AcoustiFex system delivers unmatched sound and convenience.
The Kepma Fenix™ Series offers four configurations to suit every player’s preferences:
- FGA1-130 (Natural Finish): Grand Auditorium, solid torrefied spruce top, layered mahogany back and sides. MAP: $249.99
- FGA1-130A (Natural Finish with AcoustiFex): Grand Auditorium, solid torrefied spruce top, layered mahogany back and sides, AcoustiFex K-10 Pro Pickup System. MAP: $299.99
- FGA1-130SB (Sunburst Finish): Grand Auditorium, solid torrefied spruce top, layered mahogany back and sides, sunburst finish. MAP: $249.99
- FGA1-130ASB (Sunburst Finish with AcoustiFex): Grand Auditorium, solid torrefied spruce top, layered mahogany back and sides, sunburst finish, AcoustiFex K-10 Pro Pickup System. MAP: $299.99
The new Fenix models are designed to inspire beginners and seasoned musicians alike, setting a new benchmark for performance and value in the industry.
Kepma Guitars is thrilled to announce the introduction of its versatile FC Mini Series, packed with cutting-edge technology that redefines expectations for travel-sized guitars.
The new FC Mini models include a variety of configurations to suit every player’s needs. The Spruce/Rosewood and Spruce/Mahogany options feature solid torrefied spruce tops paired with layered rosewood or mahogany back and sides, available in natural and sunburst finishes. The Mahogany/Mahogany model features a solid torrefied mahogany top with layered mahogany back and sides in a natural finish. Each guitar is offered in three versions: no pickup, with the AcoustiFex® K-10 Pro system, or equipped with the Elfin Sound System, and all come with a deluxe gig bag. Prices range from $399.99 to $549.99 MAP.
Big Sound in a Compact Package Traditionally, smaller guitars have been associated with compromised sound and tone. Kepma’s FC Mini Series shatters this notion by integrating advanced innovations and meticulous design to create a guitar that offers the full resonance and projection of a standard acoustic.
Premium Materials and Construction The torrefaction process removes moisture, oils, and sap from the wood, enhancing stability and delivering superior tonal richness. Back and sides crafted from high-quality mahogany or rosewood ensure durability and warmth in every note.
Technological Innovations
- Proprietary Bolt-On Neck Design: Kepma’s neck contour bolt-on neck joint ensures a perfect and stable connection between neck and body, offering ultimate playability and infinite adjustability.
- Rosewood Bracing: Solid rosewood bracing enhances top stability and reduces energy loss, resulting in superior articulation and sustain.
- Arched Back Design: A unique arched back improves resonance and eliminates the need for back bracing, allowing for harmonious vibrations and a fuller sound.
Enhanced Playability The FC Mini Series is engineered with the player in mind. The slightly thicker neck provides added stability, while the ergonomic C-shape design reduces fatigue during extended playing sessions. The sleek cutaway provides access to the higher notes on the fretboard for better playability. Lower string action, beveled binding, and redesigned precision sealed tuners further enhance comfort and ease of use.
Attention to Detail Kepma’s commitment to excellence is evident in every detail of the FC Mini Series:
- D'Addario XS Strings: Coated strings extend playing life and offer superior projection.
- Elegant Aesthetics: Features include a magnolia inlay on the fretboard, upgraded rosette, and a refined rosewood veneer headstock.
- Eco-Friendly Finish: A thin, water-based matte finish minimizes vibration damping for a clear, transparent sound.
Advanced Electronics for Modern Musicians
AcoustiFex K-10 Pro System Each new FC Mini Series model is available with the AcoustiFex K-10 Pro System, offering:
- Built-in reverb, delay, and chorus effects
- Bluetooth audio streaming for playing along with backing tracks
- An on-the-go USB interface for app connectivity, enabling looping, rhythm tracks, and practice tools like a metronome and tuner
- Whether you’re performing on stage or practicing at home, plugged into an amp or mixer, or simply playing unplugged, the AcoustiFex system delivers unmatched sound and convenience.
Elfin Sound System The FC Mini Series are also available with the new Elfin K-13 Sound System, developed collaboratively by Kepma and Double Acoustics. The system offers high sensitivity, accurate sound reproduction, strong output power, and low noise. The under-saddle piezo pickup delivers sweet treble and punchy bass, making it ideal for fingerstyle playing. Additionally, the preamp features a rechargeable battery system that can be conveniently charged using a standard USB-C phone charger cable. The Elfin K-13 Sound System was developed and voiced specifically for the Kepma ¾ size FC Mini Series guitars.
Complete Package Each FC Mini guitar comes with a padded deluxe gig bag and an accessory kit that includes a custom truss rod wrench, microfiber polishing cloth, bridge pins, picks, extra saddle, and string height gauge.
Purchase Options
Spruce/Rosewood, Natural Finish
- Solid Torrefied Spruce Top/Layered Rosewood Back & Sides
- No Pickup: Model FCM-SR, MAP: $449.99
- With AcoustiFex K-10 Pro: Model FCM-SRA, MAP: $549.99
- With Elfin Sound System: Model FCM-SRE, MAP: $549.99
Spruce/Rosewood, Sunburst Finish
- Solid Torrefied Spruce Top/Layered Rosewood Back & Sides, Sunburst Finish
- No Pickup: Model FCM-SR-SB, MAP: $449.99
- AcoustiFex K-10 Pro: Model FCM-SRA-SB, MAP: $549.99
- Elfin Sound System: Model FCM-SRE-SB, MAP: $549.99
Spruce/Mahogany, Natural Finish
- Solid Torrefied Spruce Top / Layered Mahogany Back & Sides, Natural Finish
- No Pickup: Model FCM-SM, MAP: $399.99
- With AcoustiFex K-10 Pro: Model FCM-SMA, MAP: $499.99
- With Elfin Sound System: Model FCM-SME, MAP: $499.99
Spruce/Mahogany, Sunburst Finish
- Solid Torrefied Spruce Top / Layered Mahogany Back & Sides, Sunburst Finish
- No Pickup: Model FCM-SM-SB, MAP: $399.99
- With AcoustiFex K-10 Pro: Model FCM-SMA-SB, MAP: $499.99
- With Elfin Sound System: Model FCM-SME-SB, MAP: $499.99
Mahogany/Mahogany, Natural Finish
- Solid Torrefied Mahogany Top / Layered Mahogany Back & Sides, Natural Finish
- No Pickup: Model FCM-MM, MAP: $399.99
- With AcoustiFex K-10 Pro: Model FCM-MMA, MAP: $499.99
- With Elfin Sound System: Model FCM-MME, MAP: $499.99
The new Kepma FC Mini Series combines portability, premium materials, and advanced technology to offer an unparalleled sound and playing experience. Whether you’re a traveling musician or a beginner seeking comfort and quality, the FC Mini Series is your perfect companion.
For more information, please visit kepmausa.com.