
Photo 1
We’re almost finished with the aging process on our project guitar. Let’s work on the fretboard, nut, and truss rod cover, and prepare the headstock for the last hurrah.
Hello and welcome back to Mod Garage. This month we’ll continue with our relic’ing project, taking a closer look at the front side of the neck and treating the fretboard and the headstock. We’ll work on the front side of the headstock in the next part, but first we must prepare it.
When we talk about a vintage Gibson fretboard from the ’50s, we’re talking about the mystic Brazilian rosewood (Dalbergia nigra) and its certain look and feel. Our Harley Benton doesn’t have a Brazilian rosewood fretboard. If it did, the fretboard material would cost more than the entire guitar because it’s so rare and limited today. Brazilian rosewood trade is restricted by CITES and almost no guitar companies use it anymore, except for some special custom shops. Other rosewoods or alternative woods are common substitutes.
Our Harley Benton fretboard is amaranth (better known as purpleheart), but sadly it was stained or painted black, giving the guitar a different look that’s closer to ebony rather than rosewood. So, there’s no way to get it brown or make it look like rosewood other than getting a new fretboard installed, which isn’t reasonable. Maybe it’s possible to get the black color out of the wood by using chemicals, but we don’t know what we’d find underneath, either. There could be another surprise waiting for us and all the work would be useless. On a budget guitar like this, we’ll have to live with this fretboard, loving it for what it is rather than hating it for what it’s not. The fretwork is surprisingly good and close to excellent, which is far from the industry standard in this price range.
The fretboard edges of well-played vintage guitars feel comfortable and round because the edges receive pressure from a player’s hand over decades.
But to show you the process of aging a fretboard, I chose a guitar with a rosewood fretboard, so you’ll know how to do this on a guitar with this type of fretboard if you want to. It’s not complicated so here we go.
Look at the slightly pale and lifeless color of the rosewood in Photo 1. It has a nice grain but is rather dull. Brazilian rosewood has a rich chocolate brown color, which clearly shows the grain of the wood.
Let’s make it less boring:
Use some fine steel wool or sanding pads to sand the rosewood. Use a soft brush afterwards to get the dust off.
Use some naphtha or alcohol and a cotton cloth to degrease the wood and get all the fine dust and dirt out of it.
Use masking tape to protect the fretboard edges and the binding, if your neck has one. You don’t need to cover the frets. They’re easy to clean after the process. Use a Q-tip and some Vaseline to protect the fretboard dots from the dye.
You need a chocolate brown wood dye and a small soft brush to apply it.
Photo 2
Some luthier supply stores offer special Brazilian rosewood dye in different shades of brown (Photo 2). I decided on a classic chocolate brown color on a solvent base for best results. Apply the dye thin and carefully and let it dry for some minutes.
Photo 3
Now look at the difference in Photo 3. It’s easy to see! If you want your fretboard darker, repeat the process until you like it. Cover your workspace with old newspapers and have an old cotton rag nearby just in case. This dye will stain everything permanently and you don’t want it on your clothes or your kitchen table. Let the fretboard dry for a day and take off the masking tape.
Use some very fine steel wool to polish the fretboard and the frets, to get any dye off the fret material easily. Use a soft brush to clean the fretboard afterwards.
Use some naphtha and a Q-tip to carefully clean the fretboard dots from any Vaseline leftovers.
Then use the amber color from the last part of this series [“DIY Relic’ing: Hardware Continued”] together with a fresh Q-tip and apply the amber color to the dots until you like the shade.
Now that we’ve made this rosewood fretboard look much closer to Brazilian rosewood, it’s time to mimic the touch and feel of it. Brazilian rosewood has a certain smell and feel that can be described as greasy compared to most other rosewoods. This is because of the oil content of this wood. We can’t naturally “oil up” other woods, but we can get close to this certain feel by waxing the fretboard rather than oiling it. This is also an easy process so let’s go for it.
Photo 4
Get a clear, hard wax for fretboards and a soft polishing brush (Photo 4). Apply a thin layer of wax to the fretboard using a cotton cloth to massage it into the wood.
Photo 5
Let it dry for some time, then wipe off any remaining excess wax and use the soft polishing brush to get this greasy look and shine on your fretboard, as seen in Photo 5.
So far, so good. We’ve taken care of the color and the feel of the fretboard but there is another haptic thing to consider when talking about vintage necks: the broken-in feeling of the fretboard edges. The fretboard edges of well-played vintage guitars feel comfortable and round because the edges receive pressure from a player’s hand over decades. This is not what is called “rolled fretboard edge,” which is a common custom shop option, but it goes in the same direction only to a much lesser degree.
Photo 6
To bring this typical broken-in feeling to your neck, you don’t need much: just a round metal bar and some time. You can do this to any guitar neck. I prefer to use a massive metal slide for pedal-steel players, but you can also use a bigger screwdriver or something similar. If possible, clamp down your guitar and use the steel bar in a 45-degree angle to move it along the edge of the fretboard, applying pressure (Photo 6). What we’re doing with this is not making a rolled edge but compressing fibres, which is exactly the natural process over time. Repeat moving the bar while applying pressure for some time and check the result until you like it. This is not done within a minute, so take your time. With the metal slide, I usually need 10-15 minutes for each edge until I like it, but this depends a lot on how hard your fretboard material is.
Photo 7
If you’re done with that part, excellent! You just finished your fretboard. Moving up the neck, the nut is our next task. The nut of our Harley Benton is pure white plastic, which not the best choice. If you want to keep it, you can sand it with some steel wool and apply some of the amber color with a Q-tip, followed with some of our mixture of dirt, dust, and ashes we used for the plastic buttons of the tuners [DIY Relic’ing Tuners, Part 2”]. Use your fingers to wipe on some of this mixture and you’re done. If you want to upgrade the nut, nylon is the historically correct material, and such nut blanks are available from numerous luthier supply stores. I decided to use an unbleached bone nut blank and make a new nut. Afterwards, I used some of the amber color and dust to make it look old (Photo 7).
Photo 8
Further up the neck is the cover for the truss rod adjustment screw with its mounting screw. Harley Benton decided to use a modern shape for it, which doesn’t look very good to me. The typical Gibson-style covers with their bell-like shape look much different, so I decided to swap the cover for such a model, modifying it for a flat bottom so it covers the whole opening for the truss rod (Photo 8). To make it look old, you can use the exact steps we used on the jack plate: break the shine with some steel wool, add some light scratches, wipe on some amber color on the white part of the cover, and then rub in some dust and dirt. You already know how to age screws, having done it many times before in the earlier parts of this ongoing project. If you need a refresher on our aging process for screws, refer back to “DIY Relic’ing: Break the Shine” for guidance.
Photo 9
The last thing we’ll do today is begin to work on the headstock of the guitar, which is often a delicate task. A lot of modders try to reshape the headstock so it will look like it’s from a vintage guitar, and, even worse, replace the headstock logo with a fake logo from another company. I would never do that. This project is about aging a guitar and not about making it an exact copy of a vintage original. Personally, I really like the headstock shape of the Harley Benton. It looks at least a little bit Gibson-like, and I also think the Harley Benton logo looks cool the way it is (Photo 9). So, aging it is very easy: Break the shine with some steel wool and wipe off the dust. Use a Q-tip and apply some layers of the amber color to the logo until you like the shade. Adding dings, dongs, and scratches will come later. In the next part of this project, we’ll take care of the backside of the neck and the body by cracking the lacquer to mimic some old nitro lacquer.
That’s it for now. We’re almost finished with this relic’ing project, but before we wrap it up, we’ll return to guitar mods in the next issue. We’ll take a deeper look at putting vintage parts into new electric guitars, so stay tuned.
Until then ... keep on modding!
- Last Call: Someday You'll Regret That Relic Job - Premier Guitar ›
- Mod Garage: DIY Relic'ing—Aging a P-90 Pickup - Premier Guitar ›
- DIY Relic'ing: Break the Shine - Premier Guitar ›
- DIY Guitar Relic'ing: Let's Crack Some Lacquer Finish - Premier Guitar ›
- It’s Rosewood, But What Kind? ›
6V6 and EL84 power sections deliver a one-two punch in a super-versatile, top-quality, low-wattage combo.
Extremely dynamic. Sounds fantastic in both EL84 and 6V6 settings. Excellent build quality.
Heavy for a 9-to-15-watt combo. Expensive.
$3,549
Divided by 13 CCC 9/15
The announcement in January 2024 that Two-Rock had acquired Divided by 13 Amplifiers (D13) was big news in the amp world. It was also good news for anyone who’d enjoyed rocking D13’s original, hand-made creations and hoped to see the brand live on. From the start of D13’s operations in the early ’90s, founder and main-man Fred Taccone did things a little differently. He eschewed existing designs, made his amps simple and tone-centric, and kept the company itself simple and small. And if that approach didn’t necessarily make him rich, it did earn him a stellar reputation for top-flight tube amps and boatloads of star endorsements.
D13’s history is not unlike Two-Rock’s. But the two companies are known for very different sounding amplifiers and very different designs. As it happens, the contrast makes the current Two-Rock company—itself purchased by long-time team members Eli Lester and Mac Skinner in 2016—a complementary new home for D13. The revived CCC 9/15 model, tested here, is from the smaller end of the reanimated range. Although, as we’ll discover, there’s little that’s truly “small” about any amp wearing the D13 badge—at least sound-wise.
Double Duty
Based on Taccone’s acclaimed dual-output-stage design, the CCC 9/15 delivers around 9 watts from a pair of 6V6GT tubes in class A mode, or 15 watts from a pair of EL84s in class AB1 mode (both configurations are cathode-biased). It’s all housed in a stylishly appointed cabinet covered in two-tone burgundy and ivory—together in perfect harmony—with the traditional D13 “widow’s peak” on a top-front panel framing an illuminated “÷13” logo plate. Measuring 22" x 211/4" x 10.5" and weighing 48 pounds, it’s chunky for a 1x12 combo of relatively diminutive wattage. But as Taccone would say, “There’s no big tone from small cabs,” and the bigging-up continues right through the rest of the design.
With a preamp stage that’s kin to the D13 CJ11, the front end of the CCC 9/15 is a little like a modified tweed Fender design. Driven by two 12AX7 twin triodes, it’s not a mile from the hallowed 5E3 Fender Deluxe, but with an EQ stage expanded to independent bass and treble knobs. Apart from those, there are volume and master volume controls with a push-pull gain/mid boost function on the former. In addition to the power and standby switches, there’s a third toggle to select between EL84 and 6V6 output, with high and low inputs at the other end of the panel. Along with two fuse sockets and an IEC power-cord receptacle, the panel on the underside of the chassis is home to four speaker-output jacks—one each for 4 ohms and 16 ohms and two for 8 ohms—plus a switch for the internal fan, acknowledging that all those output tubes can get a little toasty after a while.
“Set to 6V6 mode, the CCC 9/15 exudes ’50s-era tweed warmth and richness, with juicy compression that feels delightful under the fingertips.”
The combo cabinet is ruggedly built from Baltic birch ply and houses a Celestion G12H Creamback speaker. Construction inside is just as top notch, employing high-quality components hand-soldered into position and custom-made transformers designed to alternately handle the needs of two different sets of output tubes. In a conversation I had with Taccone several years ago discussing the original design, he noted that by supplying both sets of tubes with identical B+ levels of around 300 volts DC (courtesy of a 5AR4/GZ34 tube rectifier), the EL84s ran right in their wheelhouse—producing around 15 watts, and probably more, in cathode-biased class AB1. The 6V6s operate less efficiently, however, and can be biased hot to true class A levels, yielding just 9 to 11 watts.
Transatlantic Tone Service
Tested with a Gibson ES-355 and a Fender Telecaster, the CCC 9/15 delivers many surprises in spite of its simple controls and is toothsome and dynamic throughout its range. Between the four knobs, push-pull boost function, and 6V6/EL84 switch, the CCC 9/15 range of clean-to-grind settings is impressive regardless of volume, short of truly bedroom levels, perhaps. It also has impressive headroom and a big, robust voice for a combo that maxes out at 15 watts. Leaving the boost switch off affords the most undistorted range from the amp in either output-tube mode, though the front end will still start to push things into sweet edge-of-breakup with the volume up around 1 or 2 o’clock. Pull up that knob and kick in the boost, though, and things get thick and gutsy pretty quick.
While the power disparity between the 6V6 and EL84 settings is noticeable in the amp’s perceived output, which enhances its usefulness in different performance settings, you can also think of the function as an “era and origins” switch. Set to 6V6 mode, the CCC 9/15 exudes ’50s-era tweed warmth and richness, with juicy compression that feels delightful under the fingertips. The EL84 setting, on the other hand, ushers in ’60s-influenced voices with familiar British chime, sparkle, and a little more punch and cutting power, too.
The Verdict
If the CCC 9/15 were split into different 6V6 and EL84 amps, I’d hate to have to choose between them. Both of the amp’s tube modes offer expressive dynamics and tasty tones that make it adaptable to all kinds of venues and recording situations. From the pure, multi-dimensional tone to the surprisingly versatile and simple control set to the top-flight build quality, the CCC 9/15 is a pro-grade combo that touch-conscious players will love. It’s heavy for an amp in its power range, and certainly expensive, but the sounds and craft involved will make the cost worth it for a lot of players interested in consolidating amp collections.
Two Iconic Titans of Rock & Metal Join Forces for a Can’t-Miss North American Trek
Tickets Available Starting Wednesday, April 16 with Artist Presales
General On Sale Begins Friday, April 18 at 10AM Local on LiveNation.com
This fall, shock rock legend Alice Cooper and heavy metal trailblazers Judas Priest will share the stage for an epic co-headlining tour across North America. Produced by Live Nation, the 22-city run kicks off September 16 at Mississippi Coast Coliseum in Biloxi, MS, and stops in Toronto, Phoenix, Los Angeles, and more before wrapping October 26 at The Cynthia Woods Mitchell Pavilion in The Woodlands, TX.
Coming off the second leg of their Invincible Shield Tour and the release of their celebrated 19th studio album, Judas Priest remains a dominant force in metal. Meanwhile, Alice Cooper, the godfather of theatrical rock, wraps up his "Too Close For Comfort" tour this summer, promoting his most recent "Road" album, and will have an as-yet-unnamed all-new show for this tour. Corrosion of Conformity will join as support on select dates.
Tickets will be available starting Wednesday, April 16 at 10AM local time with Artist Presales. Additional presales will run throughout the week ahead of the general onsale beginning Friday, April 18 at 10AM local time at LiveNation.comTOUR DATES:
Tue Sep 16 – Biloxi, MS – Mississippi Coast Coliseum
Thu Sep 18 – Alpharetta, GA – Ameris Bank Amphitheatre*
Sat Sep 20 – Charlotte, NC – PNC Music Pavilion
Sun Sep 21 – Franklin, TN – FirstBank Amphitheater
Wed Sep 24 – Virginia Beach, VA – Veterans United Home Loans Amphitheater
Fri Sep 26 – Holmdel, NJ – PNC Bank Arts Center
Sat Sep 27 – Saratoga Springs, NY – Broadview Stage at SPAC
Mon Sep 29 – Toronto, ON – Budweiser Stage
Wed Oct 01 – Burgettstown, PA – The Pavilion at Star Lake
Thu Oct 02 – Clarkston, MI – Pine Knob Music Theatre
Sat Oct 04 – Cincinnati, OH – Riverbend Music Center
Sun Oct 05 – Tinley Park, IL – Credit Union 1 Amphitheatre
Fri Oct 10 – Colorado Springs, CO – Broadmoor World Arena
Sun Oct 12 – Salt Lake City, UT – Utah First Credit Union Amphitheatre
Tue Oct 14 – Mountain View, CA – Shoreline Amphitheatre
Wed Oct 15 – Wheatland, CA – Toyota Amphitheatre
Sat Oct 18 – Chula Vista, CA – North Island Credit Union Amphitheatre
Sun Oct 19 – Los Angeles, CA – Kia Forum
Wed Oct 22 – Phoenix, AZ – Talking Stick Resort Amphitheatre
Thu Oct 23 – Albuquerque, NM – Isleta Amphitheater
Sat Oct 25 – Austin, TX – Germania Insurance Amphitheater
Sun Oct 26 – Houston, TX – The Cynthia Woods Mitchell Pavilion
*Without support from Corrosion of Conformity
MT 15 and Archon 50 Classic amplifiers offer fresh tones in release alongside a doubled-in-size Archon cabinet
PRS Guitars today released the updated MT 15 and the new Archon Classic amplifiers, along with a larger Archon speaker cabinet. The 15-watt, two-channel Mark Tremonti signature amp MT 15 now features a lead channel overdrive control. An addition to the Archon series, not a replacement, the 50-watt Classic offers a fresh voice by producing retro rock “classic” tones reminiscent of sound permeating the radio four and five decades ago. Now twice the size of the first Archon cabinet, the Archon 4x12 boasts four Celestion V-Type speakers.
MT 15 Amplifier Head
Balancing aggression and articulation, this 15-watt amp supplies both heavy rhythms and clear lead tones. The MT 15 revision builds off the design of the MT 100, bringing the voice of the 100’s overdrive channel into its smaller-format sibling. Updating the model, the lead channel also features a push/pull overdrive control that removes two gain stages to produce vintage, crunchier “mid gain” tones. The clean channel still features a push/pull boost control that adds a touch of overdrive crunch. A half-power switch takes the MT to 7 watts.
“Seven years ago, we released my signature MT 15 amplifier, a compact powerhouse that quickly became a go-to for players seeking both pristine cleans and crushing high-gain tones. In 2023, we took things even further with the MT 100, delivering a full-scale amplifier that carried my signature sound to the next level. That inspired us to find a way to fit the 100's third channel into the 15's lunchbox size,” said Mark Tremonti.
“Today, I’m beyond excited to introduce the next evolution of the MT15, now featuring a push/pull overdrive control on the Lead channel and a half-power switch, giving players even more tonal flexibility to shape their sound with a compact amp. Can’t wait for you all to plug in and experience it!”
Archon Classic Amplifier Head
With a refined gain structure from the original Archon, the Archon Classic’s lead channel offers a wider range of tones colored with gain, especially in the midrange. The clean channel goes from pristine all the way to the edge of breakup. This additional Archon version was developed to be a go-to tool for playing classic rock or pushing the envelope into modern territory. The Archon Classic still features the original’s bright switch, presence and depth controls. PRS continues to stock the Archon in retailers worldwide.
“The Archon Classic is not a re-issue of the original Archon, but a newly voiced circuit with the lead channel excelling in '70s and '80s rock tones and a hotter clean channel able to go into breakup. This is the answer for those wanting an Archon with a hotrod vintage lead channel gain structure without changing preamp tube types, and a juiced- up clean channel without having to use a boost pedal, all wrapped up in a retro-inspired cabinet design,” said PRS Amp Designer Doug Sewell.
Archon 4x12 Cabinet
As in the Archon 1x12 and 2x12, the mega-sized PRS Archon 4x12 speaker cabinet features Celestion V-Type speakers and a closed-back design, delivering power, punch, and tight low end. Also like its smaller brethren, the 4x12 is wrapped in durable black vinyl and adorned with a British-style black knitted-weave grill cloth. The Archon 4x12 is only the second four-speaker cabinet in the PRS lineup, next to the HDRX 4x12.
PRS Guitars continues its schedule of launching new products each month in 2025. Stay tuned to see new gear and 40 th Anniversary limited-edition guitars throughout the year. For all of the latest news, click www.prsguitars.com/40 and follow @prsguitars on Instagram, Tik Tok, Facebook, X, and YouTube.
The Austin-based guitarist sticks with a tried-and-true combo of American guitars and British amps.
If you’ve been on the path of this spring’s Rhett Schull/Zach Person tour, you’ve been treated to one of the coolest rock ’n’ roll double bills criss-crossing North America this year. Person, who is based in Austin, put out his second full-length record, Let’s Get Loud, in March 2024, and it was packed with alt-, blues-, and psychedelic-rock anthems built around his take-no-prisoners playing.
This year, Person is road-doggin’ it around the United States as a two-piece unit with just a drummer, and PG’s Chris Kies caught up with him before he and Shull played the Eastside Bowl in Madison, Tennessee, to see what goods Person is bringing for this spring’s shows.
Brought to you by D’Addario
Customized Custom
This Gibson Jimi Hendrix 1967 Custom SG came from Gibson’s custom shop, and for Person, an SG with humbuckers is a hard combination to beat. He removed the Maestro trem system and had a tailpiece installed for tuning stability on the road, and he subjected the neck humbucker to a “Jimmy Page mod,” which entails removing the pole pieces to get closer to single-coil tones. This SG stays in standard tuning, with Ernie Ball or D’Addario strings (usually .010–.046s). Person digs Dunlop Flow Grip .88 mm picks.
Brown Sound
Person brought this 1967 Gibson SG Special back to life with a list of modifications and upgrades, including new pickups and a refinish, but its wood, neck shape, and original frets all made it worth it to him. The neck shape is narrow but chunky in Person’s hands, landing somewhere near the feel of Tyler Bryant’s 1962 Stratocaster. The pickups now are OX4 P-90s, and like the Custom, this one’s had its Maestro system amputated.
Jeannie Comes Alive
One Thanksgiving at his in-laws’ home in Dallas, Person mentioned how badly he wanted a Gibson LG-2 acoustic. As it happened, his father-in-law suspected his mother had one, which had been relegated to storage in a shed. Person and his wife’s father ventured through rain to dig it out, and sure enough, a very beat up LG-1 was withering away in its case. No local techs in Austin thought it was worth saving, except for Elaine Filion, who was used to taking on bigger restoration projects. Filion succeeded, taking the top off and installing an X-bracing system to turn the LG-1 into an LG-2-style guitar. Now, it’s got an L.R. Baggs pickup and bears the nameplate “Jeannie” on its headstock to commemorate his wife’s grandma, the original owner. Jeannie usually stays home, but Person brought her out specially for the Rundown.
Marshall Muscle
This Marshall JTM45 MkII is Person’s usual go-to. It runs just at breakup volume and gets pushed with some variation of a Pro Co RAT, his favorite dirt box.
Supro Signature
This Super Black Magick Reverb, Tyler Bryant’s signature, is along for the ride as a backup to the Marshall.
Zach Person’s Pedalboard
Person has done tours with just an overdrive pedal and nothing else, so by comparison, this two-tiered Vertex board is luxurious. Still, it’s compact and carries all he needs at the moment. The JHS Pack Rat is the core sound, set fairly heavy and dirty. The rest includes a Boss TU-3, EarthQuaker Devices Double Hoof, Vox Clyde McCoy wah, Boss BF-2, DigiTech Drop, Strymon El Capistan, and an Interstellar Audio Machines Marsling Octafuzzdrive. A TC Helicon Mic Mechanic rides along as a vocal effect so Person can keep control over his voice from night to night.