Sermon’s BiLT Relevator is finished in shoreline gold and features both an MXR Carbon Copy and BiLT’s own fuzz circuit built into the body along with a Sustainiac in the neck position. Sermon can control the parameters of the effects via a wealth of buttons, switches, and controls that are accessible on the front of the guitar. There’s a Pedaltrain Volto on his strap that supplies power to the pedals via the stereo cable. He keeps this guitar tuned a half-step down from standard.
On “Fricton” Sermon reaches for this prototype BiLT baritone that’s tuned to A and features a Mastery bridge and tremolo along with a pair of Bare Knuckle Mule humbuckers. He strings it up with a set of Elixir strings gauged .012–.068.
For the acoustic tunes, Sermon grabs either his Gibson J-35 or Gibson LG-2 American Eagle (shown here), both flattops have LR Baggs M1 pickups. The LG-2 is kept in standard tuning and used on “Trouble,” “Thief,” and “Release,” while the J-35 is tuned a half-step down and is featured on the bridge to “I Bet My Life.”
The backline for Sermon’s chimey brand of pop-rock is full of classic British tones. His wet/dry/wet setup revolves around a quartet of vintage Vox AC30 amps—two from ’64, a ’66, and a ’67.
Along with the vintage Voxes, Sermon runs an angry Friedman Smallbox 50.
Each one is modded with a Top Boost Kit from Plexi Palace.
Friedman Smallbox 50 is plugged into a 65 Amps 2x12 Whiskey cabinet.
In order to keep things tight, Sermon’s pedals are kept offstage in a rack. The first drawer contains an original silver Klon Centaur, Analog Man King of Tone, ISP Decimator II, Paul Cochrane Timmy, and a Refractor built by Aion Electronics. The whole shelf is powered by a Voodoo Lab Pedal Power 2 Plus power supply.
The second drawer houses everything that’s routed before the volume pedal. It includes an Electro-Harmonix POG 2, Voodoo Lab Micro Vibe, J. Rockett Mark Sampson Hightop, Wampler Ego Compressor, Electro-Harmonix Superego Synth Engine, and a Malekko Vibrato (which is in the effects loop of the Superego). All of the effects are run through a RJM Mini Effects Gizmo and powered by another Voodoo Lab Pedal Power 2 Plus.
The final drawer of “silliness” holds the Eventide H9, DigiTech Whammy, and Source Audio Programmable EQ. Sermon’s tech uses his iPad to connect to the H9 via Bluetooth in order to change or tweak any settings on the fly in real time.
During a typical show, Sermon needs to cover a lot of ground. After going through a Shure ULXD4 wireless unit, the signal hits a Sound Sculpture Switchblade GL before feeding one of three Eventide products: a pair of 7600 units and a H9.
Out front, Sermon uses a RJM Mastermind GT/22 for all his switching needs. He pairs that with a trio of Mission Engineering expression pedals that control the volume of individual amps and the DigiTech Whammy. Also on the board is a Boss TU-3 tuner.
Ben McKee keeps it cool with this custom bass built by Chris Stambaugh from Stambaugh Designs. It has some T-style design concepts along with a 33” scale length. It also features custom artwork using images that represent the band’s charitable foundation, The Tyler Robinson Foundation.
This Sadowsky Jazz bass is tuned to B-E-A-D for specific tunes on the band’s latest album, Smoke & Mirrors.
McKee also keeps this Mike Lull T4 tuned to B and it features passive electronics, a mahogany body and acoording to McKee, makes him feel like a “badass.”
A pair of Matchless Thunderman 50-watt heads provides McKee with his low-end rumble.
He runs the Matchless heads into a Bergantino NV412 cab.
Shane Johnson also built McKee’s bass rig. The goal was to be bulletproof yet still offer plenty of sonic options. His pedal drawer houses a Malekko B:Assmaster, Brimstone Audio Crossover Distortion XD-2, Electro-Harmonix Bass Micro Synth, and an Xotic EP Booster.
MXR Rockman X100 Recreates Tom Scholz's Iconic Boston Guitar Sound | First Look
But just as decades of advances in listening technology make the Walkman now seem clunky and dated, modern guitar tech makes the Rockman look like old news. Multi-effects units, modelers, and portable interfaces all surpass the convenience of the Rockman in form factor as well as in sheer number of sonic options. But while there are any number of ways to dial up an ’80s-style guitar tone these days, nothing’s better than the real thing. The Rockman’s analog tones are still as legit as it gets. Though Dunlop continues to produce the Guitar Ace, Metal Ace, and Bass Ace headphone amps (for a cool $99 street), a pedal version with the functionality of the original would be the ultimate modern package for ’80s fetishists, right? Enter the MXR Rockman X100.
With Tones Like These, Who Needs Options
After the release of the original Rockman, Scholz continued to develop the product, spawning a whole line. But for its pedal resurrection, the MXR team set their sights on the Rockman X100, which used hard-clipping LED diodes for its two distorted settings. The new stompbox version recreates all four modes from the original: cln2 is the default setting, cln1 in the second position is EQ’d with a mid-boost, edge delivers moderate clipping, and dist is high-gain. All are switchable via a small LED-lit mode button, and a control input allows for external mode switching. Another button activates an analog chorus circuit using MN3007 bucket brigade chips, as in the original.
To drive home the ’80s aesthetic, MXR used sliders for volume and input gain controls. Volume determines output, while input gain is tied to compression. Higher input gain means more compression, which is tuned for slower release on the two clean modes, and a fast release on both dirty modes. The X100 works in both mono and stereo, but to change between them, you have to pop off the back to access an internal switch. Just make sure a TRS cable is used for stereo mode, or else the output will be muted while the pedal is bypassed.
The only things I noticed that are missing from the original’s simple set of features is the headphone output and the echo settings. I don’t know how many players would find value in the headphone jack, and considering that would add circuitry, it’s probably best for cost and space savings that it was excluded. As for the echo, you can argue that it’s canon, but I find it to be the least essential feature and don’t miss it, personally.
(Much) More Than a Feeling
Since I do not have an original Scholz X100 sitting on my desk, I’m using YouTube videos and records—Def Leppard’s Hysteria, Huey Lewis and the News’ Sports, and Joe Satriani’s Surfing with the Alien, for example—as my reference points. Those are high bars to clear, and the MXR gets there.
The default cln2 setting delivers instant gratification, with a full-bodied, sparkly tone, no matter what guitar I played through it. And though it provides loads of ’80s fun, it’s much more versatile than that, offering a great all-round clean tone that requires no additional processing. Though it might seem odd that cln2 is the default, switching to cln1’s thinner, more mid-focused sound makes the design decision clear. I can imagine situations where I’d need to cut through a mix and cln1 would be preferred, but I found myself sticking with the default mode for all my clean needs.
The distorted modes are differentiated mostly by how much gain they offer. Edge tones live just beyond the point of overdrive, and the input gain control adds a range of extra texture. The dist mode is full-on, pick-squeal-inducing high-gain saturation, with loads of everlasting sustain. These modes lean into the aesthetic much harder than the clean modes, making it a less versatile tool, but for ’80s rock excess, I can’t imagine a better option.
On a couple recording sessions, I plugged the X100 right into an interface and board to deliver spanky direct clean tones as well as tight, saturated distortion. In doing so, I discovered that direct recording is my preferred use for the X100. That’s not to say it doesn’t sound great through an amp—it does. But plugging into a front end of an amp yields less classic and authentic Rockman sounds, as the amplifier’s preamp colors the tone. Plugged through a few Fenders, I found that the treble needed taming, a problem I didn’t have when forgoing the amp. For live playing, I might explore plugging the X100 into the return input on an amp’s effects loop or right into a powered speaker to deliver an unadulterated Rockman sound more in line with the original.
The Verdict
MXR nailed it with the Rockman X100 pedal by focusing on the limited options of the original unit and getting them just right. For $229, you not only get a great ’80s rock tone, you get what is arguably the ’80s rock tone, with no other gear required, unless you want to add a little ’80s-vintage reverb too. As a performance tool, it’s probably best to think less like you’re using a pedal and more like you’re using the original in a different form, which is to say that plugging straight into an amp isn’t the only way to get the sound you want—and, in fact, it’s probably not even the best way. For recording, it’s a perfect tool. PG
My Morning Jacket’s Is, their 10th album, released on March 21, and as we reported in our feature on the band in our May print issue, it showcased a band exercising their classic strengths as well as newfound vision and curiosity. Helmed by superstar producer Brendan O’Brien, Is finds MMJ at their anthemic, psychedelic best.
We caught up with Carl Broemel for a Rig Rundown back in 2015, but on this year’s tour, PG’s John Bohlinger checked in with all three axemen—Jim James, Broemel, and bassist Tom Blankenship—to hear about their road rigs. In Broemel’s estimation, they’re lazy—they just like to bring everything.
Brought to you by D’Addario.
Three's a Crowd
This gorgeous Gibson Jimi Hendrix 1967 SG Custom, aged by Murphy Labs, initially had three humbuckers, but James kept hitting his pick on the middle pickup, so it got the yank—as did the hefty bridge and Maestro Vibrola system, which were replaced with a simple stopbar tailpiece.
Mirror Image
James picked up this 1998 Gibson Flying V right around when My Morning Jacket got started. He traced and ordered the flashy mirror pickguard himself. It’s got Gibson pickups, though James isn’t sure of the models.
Jim James' Jimmy
James plucked this one-of-a-kind from Scott Baxendale’s collection of restored vintage guitars. He guesses it’s either an old Kay or Harmony guitar, but the decorations, including the custom plastic headstock plaque, make exact identification difficult. But it was clear this one was meant for James, since it has his name on it.
Elsewhere backstage is James’ Epiphone Jim James ES-335, a custom shop Fender Telecaster and Strat, a 1967 Gretsch Chet Atkins Country Gentleman, and a Gibson Barney Kessel.
Make Love, Not War
James loves repurposing old military equipment for creative, peaceful purposes, which is how this old radar system came to be a part of his live amplification kit. Along with the old tech, James runs two 3 Monkeys Orangutan heads through a 3 Monkeys cab.
Jim James' Pedalboard
James’ board is built around a pair of GigRig QuarterMaster switching systems, which lets him navigate the stomps you see here: a Devi Ever US Fuzz, Boss BD-2w, SoloDallas Schaffer Boost, Boss OC-2, EarthQuaker Devices Spatial Delivery, Strymon blueSky, EQD Ghost Echo, Malekko Spring Chicken, ISP Deci-Mate, Electro-Harmonix Mel9, UA Starlight Echo Station, and UA Astra Modulation Machine. A D’Addario Chromatic Pedal Tuner duo keep things on pitch, a Strymon Zuma and Ojai pair handle the power, and a Radial SGI-44 line driver maintains clarity.
Arts and Crafts Night
One night while a bit tipsy, Broemel took out his paint pens and set to work on this Gibson Les Paul Standard Faded, resulting in this masterpiece. He also removed the pickup selector switch; even though the neck pickup remains, it never gets used.
Relic By Broemel
This 1988 Les Paul Standard predates the band, and Broemel has given it its aged finish over the years—on one occasion, it fell out of a truck. It’s been treated to a Seymour Duncan pickup upgrade and occasional refrets when required.
Carl's Creston
This Creston Lea offset has two Novak lipstick pickups in the neck, with a switch to engage just one or both, plus a low-end roll-off control. It’s finished in the same blue-black color as Broemel’s house and sports a basil leaf on the headstock in tribute to Broemel’s son, Basil.
Also in the wardrobe are a shiny new Duesenberg tuned to open G, and a custom shop Fender Telecaster with a fattened neck and Bigsby to swing it closer to Broemel’s beloved LPs.
Milk Route
Broemel routes his GFI Ultra pedal steel, which is tuned to E9, through a board which includes a Milkman The Amp, which is projected through the speaker of a Fender Princeton Reissue combo. Operated with another GigRig QuarterMaster, the board also includes an Eventide H9, Moog MF Delay, Fender The Pelt, MXR Phase 90, EHX Nano POG, Xotic Effects EP Booster, Source Audio C4, and a Peterson StroboStomp HD.
Side-Carr
This time out, Broemel is running two Carr Slant 6V heads in stereo.
Carl Broemel's Pedalboard
Broemel commissioned XAct Tone Solutions to build this double-decker board, which depends on a GigRig G3S switching system. From top to bottom (literally), it includes a Boss TU-3, Durham Electronics Sex Drive, JAM Pedals Tubedreamer, Source Audio Spectrum, JAM Retrovibe, MXR Phase 100, Fender The Pelt, Origin Effects SlideRIG, 29 Pedals EUNA, two Eventide H9s, Kingsley Harlot V3, JAM Delay Llama, Merix LVX, Hologram Chroma Console, and EHX POGIII. A wah and Mission Engineering expression pedal sit on the left side, while a Lehle volume pedal and Gamechanger Audio Plus hold down the right edge.
Utility units include two SGI TX interfaces, two Strymon Ojais and a Strymon Zuma, and a Cioks Crux.
More From the Creston Crew
Blankenship, too, has brought along a few guitars from Lea, including these Precision-bass and Jazz-bass models. The dark-sparkle P-style rocks with GHS flatwound strings, while the natural-finish J-style has roundwounds.
Emperor's New Groove
Blankenship just got these brand-new Emperor cabinets, through which he cranks his Mesa Boogie WD-800 Subway heads.
Tom Blankenship’s Pedalboard
Like James, Blankenship uses a GigRig QuarterMaster to jump between his effects. After his Boss TU-3, that includes an Origin Effects Cali76, DigiTech Whammy Ricochet, Pepers’ Pedals Humongous Fuzz, MXR Bass Octave Deluxe, Tronographic Rusty Box, and EHX Bassballs Nano. A Voodoo Labs Pedal Power 2 Plus lights things up, and a Radial SGI TX keeps the signal squeaky clean.
Shop My Morning Jacket's Rig
EarthQuaker Devices host Echo Reverb Pedal
ISP Technologies DECI-MATE Micro Noise Reduction Pedal
Electro-Harmonix Mel9 Tape Replay Machine Pedal
EarthQuaker Devices Spatial Delivery Envelope Filter Pedal
Universal Audio UAFX Starlight Echo Station Delay Pedal
Universal Audio UAFX Astra Modulation Machine Pedal
Fender Custom Shop Stratocaster
